Date: Sun, 23 Jan 2011 19:44:04 +0100 From: Hans Petter Selasky <hselasky@c2i.net> To: Matthias Apitz <guru@unixarea.de> Cc: mav@freebsd.org, freebsd-usb@freebsd.org Subject: Re: da(4) not attaching to USB drive Message-ID: <201101231944.04706.hselasky@c2i.net> In-Reply-To: <20110123182918.GA16104@tinyCurrent> References: <20110122104239.GA4991@tinyCurrent> <201101231748.24599.hselasky@c2i.net> <20110123182918.GA16104@tinyCurrent>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sunday 23 January 2011 19:29:18 Matthias Apitz wrote: > El d=C3=ADa Sunday, January 23, 2011 a las 05:48:24PM +0100, Hans Petter = Selasky=20 escribi=C3=B3: > > On Sunday 23 January 2011 10:06:00 Hans Petter Selasky wrote: > > > Hi Mav, > > >=20 > > > Do you know if there are any recent changes in the SCSI layer on > > > FreeBSD that will affect USB SCSI devices? > >=20 > > Another idea: > >=20 > > Maybe your device is too late identifying itself. You could try: > >=20 > > usbconfig -d X.Y set_config 0 > >=20 > > Then: > >=20 > > usbconfig -d X.Y set_config 1 > >=20 > > After that the device has been plugged. >=20 > usbconfig -d X.Y set_config 1 always gives > usbconfig: could not set config index: Input/output error > regardless if the disk is plugged in or not; >=20 > today once it connected by its own, i.e. it was sitting pluged in and > after a while it diconnected and connected again (without my action, I > was reading some mail): >=20 > ... > Jan 23 18:10:03 tinyCurrent kernel: (probe0:umass-sim0:0:0:0): AutoSense > failed Jan 23 18:10:03 tinyCurrent kernel: ugen4.3: <Freecom> at usbus4 > (disconnected) Jan 23 18:10:03 tinyCurrent kernel: umass0: at uhub4, port > 1, addr 3 (disconnected) Jan 23 18:10:05 tinyCurrent root: Unknown USB > device: vendor 0x07ab product 0xfc8e bus uhub4 Jan 23 18:10:05 tinyCurrent > kernel: ugen4.3: <Freecom> at usbus4 > Jan 23 18:10:05 tinyCurrent kernel: umass0: <Bulk Only Interface> on usbu= s4 > Jan 23 18:10:05 tinyCurrent kernel: umass0: SCSI over Bulk-Only; quirks = =3D > 0x0000 Jan 23 18:10:06 tinyCurrent kernel: umass0:0:0:-1: Attached to > scbus0 Jan 23 18:11:16 tinyCurrent kernel: (probe0:umass-sim0:0:0:0): > AutoSense failed Jan 23 18:11:16 tinyCurrent kernel: ugen4.3: <Freecom> at > usbus4 (disconnected) Jan 23 18:11:16 tinyCurrent kernel: umass0: at > uhub4, port 1, addr 3 (disconnected) >=20 > and now it connects with success by its own: >=20 > Jan 23 18:11:18 tinyCurrent kernel: ugen4.3: <Freecom> at usbus4 > Jan 23 18:11:18 tinyCurrent kernel: umass0: <Bulk Only Interface> on usbu= s4 > Jan 23 18:11:18 tinyCurrent kernel: umass0: SCSI over Bulk-Only; quirks = =3D > 0x0000 Jan 23 18:11:18 tinyCurrent root: Unknown USB device: vendor 0x07ab > product 0xfc8e bus uhub4 Jan 23 18:11:19 tinyCurrent kernel: > umass0:0:0:-1: Attached to scbus0 Jan 23 18:11:19 tinyCurrent kernel: da0 > at umass-sim0 bus 0 scbus0 target 0 lun 0 Jan 23 18:11:19 tinyCurrent > kernel: da0: <Freecom Hard Drive XS 1.00> Fixed Direct Acc ess SCSI-2 > device Jan 23 18:11:19 tinyCurrent kernel: da0: 40.000MB/s transfers >=20 Try adding some mass storage quirks: kldload usb_quirk usbconfig -d X.Y add_dev_quirk_vplh x x x x x x =2D-HPS
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201101231944.04706.hselasky>