Date: Mon, 7 Feb 2011 00:55:37 -0800 From: Jeremy Chadwick <freebsd@jdc.parodius.com> To: Greg Bonett <greg@bonett.org> Cc: freebsd-stable <freebsd-stable@freebsd.org> Subject: Re: 8.1 amd64 lockup (maybe zfs or disk related) Message-ID: <20110207085537.GA20545@icarus.home.lan> In-Reply-To: <1297065041.754.12.camel@ubuntu> References: <1297026074.23922.8.camel@ubuntu> <20110207045501.GA15568@icarus.home.lan> <1297065041.754.12.camel@ubuntu>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sun, Feb 06, 2011 at 11:50:41PM -0800, Greg Bonett wrote: > Thanks for the response. > I have no tunings in /boot/loader.conf > according to http://wiki.freebsd.org/ZFSTuningGuide for amd64 > "FreeBSD 7.2+ has improved kernel memory allocation strategy and no > tuning may be necessary on systems with more than 2 GB of RAM. " > I have 8GB of ram. > do you think this is wrong? > > Handbook recommends these (but says their test system has 1gb ram): > vm.kmem_size="330M" > vm.kmem_size_max="330M" > vfs.zfs.arc_max="40M" > vfs.zfs.vdev.cache.size="5M" > > what do you recommend? The Wiki is outdated, I'm sorry to say. Given that you have 8GB RAM, I would recommend these settings. Please note that some of these have become the defaults in 8.1 (depending on when your kernel was built and off of what source date), and in what will soon be 8.2: /boot/loader.conf : # # ZFS tuning parameters # NOTE: Be sure to see /etc/sysctl.conf for additional tunings # # Increase vm.kmem_size to allow for ZFS ARC to utilise more memory. vm.kmem_size="8192M" vfs.zfs.arc_max="6144M" # Disable ZFS prefetching # http://southbrain.com/south/2008/04/the-nightmare-comes-slowly-zfs.html # Increases overall speed of ZFS, but when disk flushing/writes occur, # system is less responsive (due to extreme disk I/O). # NOTE: Systems with 8GB of RAM or more have prefetch enabled by default. vfs.zfs.prefetch_disable="1" # Disable UMA (uma(9)) for ZFS; amd64 was moved to exclusively use UMA # on 2010/05/24. # http://lists.freebsd.org/pipermail/freebsd-stable/2010-June/057162.html vfs.zfs.zio.use_uma="0" # Decrease ZFS txg timeout value from 30 (default) to 5 seconds. This # should increase throughput and decrease the "bursty" stalls that # happen during immense I/O with ZFS. # http://lists.freebsd.org/pipermail/freebsd-fs/2009-December/007343.html # http://lists.freebsd.org/pipermail/freebsd-fs/2009-December/007355.html vfs.zfs.txg.timeout="5" /etc/sysctl.conf : # # ZFS tuning parameters # NOTE: Be sure to see /boot/loader.conf for additional tunings # # Increase number of vnodes; we've seen vfs.numvnodes reach 115,000 # at times. Default max is a little over 200,000. Playing it safe... kern.maxvnodes=250000 # Set TXG write limit to a lower threshold. This helps "level out" # the throughput rate (see "zpool iostat"). A value of 256MB works well # for systems with 4GB of RAM, while 1GB works well for us w/ 8GB on # disks which have 64MB cache. vfs.zfs.txg.write_limit_override=1073741824 Be aware that the vfs.zfs.txg.write_limit_override tuning you see above may need to be adjusted for your system. It's up to you to figure out what works best in your environment. > I think the ad0: FAILURE - READ_DMA4 errors may be from a bad sata cable > (or rather, a 12in sata cable connecting a drive that is one inch away) > I'm ordering a new drive bay to improve this, but should a bad cable > cause lockups? Semantic point: it's READ_DMA48, not READ_DMA4. The "48" indicates 48-bit LBA addressing. There is no 4-bit LBA addressing mode. The term "lock up" is also too vague. If by "lock up" you mean "the system seems alive, hitting NumLock on the console keyboard toggles the LED", then the kernel is very likely spending too much of its time spinning in something (such as waiting for commands to return from the SATA controller, which could also indirectly be the controller waiting for the disk to respond to commands). If by "lock up" you mean "the system is literally hard locked, nothing responds, I have to hit physical Reset or power-cycle the box", then no, a bad cable should not be able to cause that. > #smartctl -a /dev/ad0 > > === START OF INFORMATION SECTION === > Model Family: Western Digital Caviar Green (Adv. Format) family > Device Model: WDC WD10EARS-00Y5B1 First thing to note is that this is one of those new 4KB sector drives. I have no personal experience with them, but they have been talked about on the FreeBSD lists for quite some time, especially with regards to ZFS. The discussions involve performance. Just a FYI point. > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 > 3 Spin_Up_Time 0x0027 121 121 021 Pre-fail Always - 6933 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 30 > 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 > 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 > 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2664 > 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 > 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 28 > 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 27 > 193 Load_Cycle_Count 0x0032 135 135 000 Old_age Always - 196151 > 194 Temperature_Celsius 0x0022 125 114 000 Old_age Always - 22 > 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 > 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 > 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 > 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 > 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining > LifeTime(hours) LBA_of_first_error > # 1 Short offline Completed without error 00% 1536 Your disk looks "almost" fine. There are no indicators of bad blocks or CRC errors (which indicate bad SATA cables or physical PCB problems on the disk) -- that's the good part. The bad part: Attribute 193. Your disk is literally "load cycling" (which is somewhat equivalent to a power cycle; I'd rather not get into explaining what it is, but it's not good) on a regular basis. This problem with certain models of Western Digital disks has been discussed on the FreeBSD lists before. There have been statements made by users that Western Digital has indirectly acknowledged this problem, and fixed it in a later drive firmware revision. Please note that in some cases WD did not increment/change the firmware revision string in their fix, so you can't rely on that to determine anything. Would this behaviour cause READ_DMAxx and WRITE_DMAxx errors? Absolutely, no doubt about it. My recommendations: talk to Western Digital Technical Support and explain the problem, point them to this thread, and get a fixed/upgraded firmware from them. If they do not acknowledge the problem or you get stonewalled, I recommend replacing the drive entirely with a different model (I highly recommend the Caviar Black drives, which do not have this problem). If they give you a replacement firmware, you'll probably need a DOS boot disk to accomplish this, and need to make sure your BIOS does not have AHCI mode enabled (DOS won't find the disk). You can always re-enable AHCI after the upgrade. If you don't have a DOS boot disk, you'll need to explain to Western Digital that you need them to give you a bootable ISO that can allow you to perform the upgrade. If you need me to dig up mailing lists posts about this problem I can do so, but it will take me some time. The discussions might have been for a non-4K-sector Green drive as well, but it doesn't matter, the problem is known at this point. -- | Jeremy Chadwick jdc@parodius.com | | Parodius Networking http://www.parodius.com/ | | UNIX Systems Administrator Mountain View, CA, USA | | Making life hard for others since 1977. PGP 4BD6C0CB |
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20110207085537.GA20545>