Date: Fri, 10 Jul 2020 20:29:03 +0200 From: Guido van Rooij <guido@gvr.org> To: Kyle Evans <kevans@freebsd.org> Cc: FreeBSD-STABLE Mailing List <freebsd-stable@freebsd.org> Subject: Re: 12.1p7 no longer boots after doing zpool upgrade -a Message-ID: <20200710182903.GA7412@gvr.gvr.org> In-Reply-To: <CACNAnaGbCknS18yLv1ow2FFnj5xSMHXQZgxfRPMUMTb5ujB=fw@mail.gmail.com> References: <20200709131201.GA3464@co.gvr.org> <CACNAnaGbCknS18yLv1ow2FFnj5xSMHXQZgxfRPMUMTb5ujB=fw@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, Jul 09, 2020 at 08:24:54AM -0500, Kyle Evans wrote: > On Thu, Jul 9, 2020 at 8:12 AM Guido van Rooij <guido@gvr.org> wrote: > > > > I did a zpool upgrade -a to enable large_dnode and spacemap_v2. > > After that, I did: > > gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 2 ada0 > > gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 2 ada1 > > and: > > gpart bootcode -p /boot/boot1.efifat -i 1 ada0 > > gpart bootcode -p /boot/boot1.efifat -i 1 ada1 > > > > Now the system no longer boots from either disk and drops to the efi shell. > > This method of updating the ESP is no longer recommended for new 12.x > installations -- we now more carefully construct the ESP with an > /EFI/FreeBSD/loader.efi where loader.efi is /boot/loader.efi. You will > want to rebuild this as such, and that may fix part of your problem. Hi Kyle, Thnaks for your asnwer. I have not got it to work with that configuration. What did work was to replace the /efi/boot/BOOTx64.efi with loader.efi and and change the content of startup.nsh with loader.efi. Withoyt the above answer I wouldn't have figure it out that quickly so thanks! I will investigate further once I have more time (early next week probably). > > > From memory, the partitions on ada0 and ada1 are as folows: > > > > 1 efi > > 2 freebsd-boot > > 3 freebsd-swap > > 4 freebsd > > p4 is a geli partition with zfs in it. > > ada0p4.eli and ada1p4.eli form a mirrored zpool (called zroot).. > > > > The boot process no longer asks for a GELi password. It just isues > > a no zfs pools found. > > > > When I boot from a stick, it does ask for the GELi password. When > > I set currdev correctly in the loader, I am able to load the kernel, > > opensolaris.ko and zfs.ko. However booting failed because I get an > > Error: Solaris: NOTICE: Cannot find the pool label for 'zroot' > > > > Was vfs.root.mountfrom set correctly? My completely uneducated guess > is that it likely wasn't and we couldn't locate the zpool.cache -- the > value of vfs.root.mountfrom should basically match the currdev format > here, except without a trailing colon. I did not set this sysctl so most likely that was the cause. As the system is up and running again I didn't test it. Let me know if you want me to. -Guido
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20200710182903.GA7412>