Date: Tue, 7 May 2024 12:51:31 -0700 From: Mark Millard <marklmi@yahoo.com> To: Mike Karels <mike@karels.net> Cc: HP van Braam <hp@tmm.cx>, FreeBSD ARM List <freebsd-arm@freebsd.org>, Emmanuel Vadot <manu@freebsd.org> Subject: Re: SD card timeouts on older Raspberry Pi 4 models on 14.1-BETA Message-ID: <25A622F4-330F-409B-94B2-D963B4F3FE33@yahoo.com> In-Reply-To: <9D83BC30-AA64-4FE3-9E22-28DE2F75C37D@karels.net> References: <kcEE.xnqWzH1TRt%2BOvb/eMAIaxA.gG1Vx6qg2gE@14d7edb59102> <9D83BC30-AA64-4FE3-9E22-28DE2F75C37D@karels.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On May 7, 2024, at 11:58, Mike Karels <mike@karels.net> wrote:
> On 7 May 2024, at 13:17, HP van Braam wrote:
> > I'll note that my testing that Mike mentioned was without any USB =
devices
> > being plugged into any USB port: Just Serial console, Ethernet =
connection,
> > power supply, and the fan's power-pin connections. Nothing else =
connected.
>=20
> Thanks for confirming! It just *looks* like the bug I'm chasing then!
>=20
> > Only the old 4 GiByte Rev 1.1 RPi4B's failed to boot 14.1.
>=20
> I'll test this locally as well, I think I still have one kicking =
around.
>=20
> One thing I'd like you to check is to see if the "mmc" overlay is =
enabled in
> config.txt. If it is can you try commenting it out? If that does work =
problems
> are probably related after all.
>=20
>=20
> I also tried commenting out the mmc overlay, with the same result as =
Mark.
> Two other tests: I added 15-current and 14.0 kernels to the BETA1 =
image, and=20
> booted each of them. Both worked. So the difference must be in the =
kernel.
boot -v extractions for the 4 GiByte Rev 1.1 RPi4B:
Processing 1 pin-config node(s) in pinctrl-0 for mmcnr@7e300000
. . .
simplebus0: <mmc@7e202000> mem 0x7e202000-0x7e2020ff irq 17 disabled =
compat brcm,bcm2835-sdhost (no driver attached)
. . .
simplebus0: <mmc@7e300000> mem 0x7e300000-0x7e3000ff irq 24 disabled =
compat brcm,bcm2835-mmc (no driver attached)
. . .
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 73 on simplebus0
sdhci_bcm0: SDHCI frequency: 250MHz
sdhci_bcm0-slot0: 250MHz HS 4bits VDD: 3.3V VCCQ: 3.3V DRV: B PIO =
removable
sdhci_bcm0-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D REGISTER =
DUMP =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x01ff0000 | Host ctl: 0x00000000
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x027f003b | Sig enab: 0x00000000
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm0-slot0: Card inserted
mmc0: <MMC/SD bus> on sdhci_bcm0
. . .
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff =
irq 79 on simplebus1
sdhci_bcm1: SDHCI frequency: 100MHz
sdhci_bcm1-slot0: 100MHz HS 8bits VDD: 3.3V 1.8V VCCQ: 3.3V DRV: BC PIO =
embedded
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D REGISTER =
DUMP =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm1-slot0: Sys addr: 0xf811e600 | Version: 0x00001002
sdhci_bcm1-slot0: Blk size: 0x00007200 | Blk cnt: 0x00000000
sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present: 0x1fff0000 | Host ctl: 0x00000002
sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080
sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107
sdhci_bcm1-slot0: Timeout: 0x0000000e | Int stat: 0x00000003
sdhci_bcm1-slot0: Int enab: 0x027f003b | Sig enab: 0x00000000
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525
sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm1: vqmmc-supply regulator found
sdhci_bcm1-slot0: Card inserted
mmc1: <MMC/SD bus> on sdhci_bcm1
. . .
sdhci_bcm0-slot0: Divider 313 for freq 399361 (base 250000000)
mmc0: Probing bus
. . .
sdhci_bcm0-slot0: Divider 313 for freq 399361 (base 250000000)
mmc0: Probing bus
usbus0: 5.0Gbps Super Speed USB v3.0
mmc0: SD probe: failed
mmc0: MMC probe: failed
mmc0: Current OCR: 0x00000000
mmc0: No compatible cards found on bus
sdhci_bcm1-slot0: Divider 125 for freq 400000 (base 100000000)
mmc1: Probing bus
ugen0.1: <(0x1106) XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on =
usbus0
mmc1: SD 2.0 interface conditions: OK
mmc1: SD probe: OK (OCR: 0x40ff8000)
mmc1: Current OCR: 0x00ff8000
mmc1: Probing cards
mmc1: New card detected (CID 03534453453332478080fba7d2011700)
mmc1: New card detected (CSD 400e00325b590000edc87f800a404000)
mmc1: Card at relative address 0xe624 added:
mmc1: card: SDHC SE32G 8.0 SN 80FBA7D2 MFG 07/2017 by 3 SD
mmc1: quirks: 0
mmc1: bus: 4bit, 50MHz (high speed timing)
mmc1: memory: 62333952 blocks, erase sector 8192 blocks
mmc1: setting transfer rate to 50.000MHz (high speed timing)
sdhci_bcm1-slot0: Divider 1 for freq 50000000 (base 100000000)
mmcsd0: 32GB <SDHC SE32G 8.0 SN 80FBA7D2 MFG 07/2017 by 3 SD> at mmc1 =
50.0MHz/4bit/65535-block
GEOM: new disk mmcsd0
mmc1: setting bus width to 4 bits high speed timing
. . .
Release APs...done
TCP_ratelimit: Is now initialized
regulator: shutting down unused regulators
regulator: shutting down cam-dummy-reg... ok
uhub0: 5 ports with 4 removable, self powered
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on =
usbus0
uhub1: 4 ports with 4 removable, self powered
sdhci_bcm1-slot0: Controller timeout
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D REGISTER =
DUMP =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002
sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000001
sdhci_bcm1-slot0: Argument: 0x03b723ff | Trn mode: 0x00000012
sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007
sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080
sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107
sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0009
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525
sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
mmcsd0: Error indicated: 1 Timeout
sdhci_bcm1-slot0: Controller timeout
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D REGISTER =
DUMP =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002
sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000001
sdhci_bcm1-slot0: Argument: 0x03b723ff | Trn mode: 0x00000012
sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007
sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080
sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107
sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000021
sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525
sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
mmcsd0: Error indicated: 1 Timeout
sdhci_bcm1-slot0: Controller timeout
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D REGISTER =
DUMP =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002
sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000004
sdhci_bcm1-slot0: Argument: 0x03b723c1 | Trn mode: 0x00000036
sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007
sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080
sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107
sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000021
sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525
sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
mmcsd0: Error indicated: 1 Timeout
mmcsd0: Error indicated: 1 Timeout
mmcsd0: Error indicated: 1 Timeout
mmcsd0: Error indicated: 1 Timeout
mmcsd0: Error indicated: 1 Timeout
mountroot: waiting for device /dev/ufs/rootfs...
Mounting from ufs:/dev/ufs/rootfs failed with error 19.
Loader variables:
vfs.root.mountfrom=3Dufs:/dev/ufs/rootfs
vfs.root.mountfrom.options=3Drw
Manual root filesystem specification:
<fstype>:<device> [options]
Mount <device> using filesystem <fstype>
and with the specified (optional) option list.
eg. ufs:/dev/da0s1a
zfs:zroot/ROOT/default
cd9660:/dev/cd0 ro
(which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
? List valid disk boot devices
. Yield 1 second (for background tasks)
<empty line> Abort manual input
mountroot>=20
I wonder about unintended consequence related to the
notices:
regulator: shutting down unused regulators
regulator: shutting down cam-dummy-reg... ok
Also I wonder about use of uninitialized memory that might be
sensitive to very detailed build differences for what is seen
for the uninitialized value(s).
Not that I have any specific evidence of either.
=3D=3D=3D
Mark Millard
marklmi at yahoo.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?25A622F4-330F-409B-94B2-D963B4F3FE33>