Date: Thu, 01 Apr 2004 15:12:35 -0800 From: Drew Tomlinson <drew@mykitchentable.net> To: FreeBSD Questions <freebsd-questions@freebsd.org> Subject: Firewire Drive Not Recognized During Boot Message-ID: <406CA1E3.2020106@mykitchentable.net>
next in thread | raw e-mail | index | archive | help
I'm using 4.9-RELEASE-p4 and have an 80 GB IDE hard drive in a firewire enclosure. When I reboot my system, the drive is not recognized. However if I unplug/plug the firewire cable, then the drive is recognized. I've included my dmesg output below. Any ideas on what is going on or what I'm doing wrong? Thanks, Drew blacklamb# cat /var/run/dmesg.boot Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.9-RELEASE-p4 #7: Wed Mar 24 16:32:40 PST 2004 tomlinson_dr@blacklamb.mykitchentable.net:/usr/obj/usr/src/sys/BLACKLAMB Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (601.37-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x673 Stepping = 3 Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE> real memory = 201261056 (196544K bytes) config> di pcic0 No such device: pcic0 Invalid command or syntax. Type `?' for help. config> di ata1 No such device: ata1 Invalid command or syntax. Type `?' for help. config> di ata0 No such device: ata0 Invalid command or syntax. Type `?' for help. config> di aic0 No such device: aic0 Invalid command or syntax. Type `?' for help. config> di adv0 No such device: adv0 Invalid command or syntax. Type `?' for help. config> q avail memory = 192417792 (187908K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc0343000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc034309c. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 11 entries at 0xc00fdf10 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard IOAPIC #0 intpin 19 -> irq 2 IOAPIC #0 intpin 18 -> irq 5 IOAPIC #0 intpin 17 -> irq 10 IOAPIC #0 intpin 16 -> irq 11 pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <ATI Mach64-GZ graphics accelerator> at 0.0 isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0x1c90-0x1c9f at device 4.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1ca0-0x1cbf irq 2 at device 4.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered Timecounter "PIIX" frequency 3579545 Hz chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 4.3 on pci0 ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x1000-0x10ff mem 0xfc100000-0xfc100fff irq 5 at device 5.0 on pci0 ahc0: Using left over BIOS settings aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x1400-0x14ff mem 0xfc101000-0xfc101fff irq 5 at device 5.1 on pci0 ahc1: Host Adapter Bios disabled. Using default SCSI device parameters aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs fxp0: <Intel 82559 Pro/100 Ethernet> port 0x1cc0-0x1cff mem 0xfc000000-0xfc0fffff,0xfc102000-0xfc102fff irq 2 at device 6.0 on pci0 fxp0: Ethernet address 00:e0:18:c4:f4:5e inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x1800-0x18ff mem 0xfc103000-0xfc103fff irq 10 at device 9.0 on pci0 fwohci0: <VIA VT6306> port 0x1c00-0x1c7f mem 0xfc104000-0xfc1047ff irq 11 at device 10.0 on pci0 fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channel is 8. fwohci0: EUI64 00:40:63:00:00:00:07:ff fwohci0: Phy 1394a available S400, 3 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 if_fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:40:63:00:07:ff sbp0: <SBP2/SCSI over firewire> on firewire0 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc800ffc1, gen=1, CYCLEMASTER mode firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me) firewire0: bus manager 1 (me) pcib2: <DEC 21152 PCI-PCI bridge> at device 12.0 on pci0 pci2: <PCI bus> on pcib2 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcd7ff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 SMP: AP CPU #1 Launched! ad0: 76319MB <GENERIC GENERIC> [155061/16/63] at ata0-master UDMA33 ad1: 76319MB <WDC WD800AB-22CBA0> [155061/16/63] at ata0-slave UDMA33 acd0: CDROM <HITACHI CDR-8435> at ata1-master PIO4 Waiting 2 seconds for SCSI devices to settle firewire0: New S400 device ID:00d04b0ce0100707 Mounting root from ufs:/dev/da0s1a da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE SX19171W 9D32> Fixed Direct Access SCSI-2 device da0: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing Enabled da0: 8683MB (17783112 512 byte sectors: 64H 32S/T 8683C) da1 at ahc0 bus 0 target 2 lun 0 da1: <SEAGATE SX19171W 9D32> Fixed Direct Access SCSI-2 device da1: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing Enabled da1: 8683MB (17783112 512 byte sectors: 64H 32S/T 8683C)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?406CA1E3.2020106>