Date: Wed, 2 Apr 2008 09:30:40 +0100 From: "Stuart Fraser" <stuart@stuartfraser.net> To: <pyunyh@gmail.com> Cc: freebsd-current@freebsd.org Subject: RE: vge(4) driver not working at 1G speeds Message-ID: <48a901c8949b$d88166e0$898434a0$@net> In-Reply-To: <20080402081643.GC18494@cdnetworks.co.kr> References: <0fc501c893c7$dfbf99b0$9f3ecd10$@net> <20080402002729.GA18494@cdnetworks.co.kr> <483f01c89493$4b8d8b90$e2a8a2b0$@net> <20080402081643.GC18494@cdnetworks.co.kr>
next in thread | previous in thread | raw e-mail | index | archive | help
Oops, no coffee yet, here you go. pcib3: slot 0 INTA hardwired to IRQ 28 vge0: <VIA Networking Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfeaffc00-0xfeaffcff irq 28 at device 0.0 on pci3 vge0: Reserved 0x100 bytes for rid 0x14 type 3 at 0xfeaffc00 miibus0: <MII bus> on vge0 ukphy0: <Generic IEEE 802.3u media interface> PHY 22 on miibus0 ukphy0: OUI 0x0090c3, model 0x0019, rev. 0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto vge0: using obsoleted if_watchdog interface vge0: bpf attached vge0: Ethernet address: 00:40:63:f3:7e:28 ioapic1: routing intpin 4 (PCI IRQ 28) to vector 49 vge0: [MPSAFE] vge0: [ITHREAD] ta S -----Original Message----- From: owner-freebsd-current@freebsd.org [mailto:owner-freebsd-current@freebsd.org] On Behalf Of Pyun YongHyeon Sent: 02 April 2008 09:17 To: Stuart Fraser Cc: freebsd-current@freebsd.org Subject: Re: vge(4) driver not working at 1G speeds On Wed, Apr 02, 2008 at 08:29:27AM +0100, Stuart Fraser wrote: > Hi, > Here is the dmesg section, it appears to be using UKPHY so as you say if the > older chips used a different physical layer perhaps we have a problem in > there. > > -- dmesg -- > pci3: <ACPI PCI bus> on pcib3 > vge0: <VIA Networking Gigabit Ethernet> port 0xe800-0xe8ff mem > 0xfeaffc00-0xfeaffcff irq 28 at device 0.0 on pci3 > miibus0: <MII bus> on vge0 > ukphy0: <Generic IEEE 802.3u media interface> PHY 22 on miibus0 This is the reason why I requested verbosed boot messages. ukphy(4) prints OUI/model number of the PHY in verbosed boot mode. Would you show me that information? > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > vge0: using obsoleted if_watchdog interface > vge0: Ethernet address: 00:40:63:f3:7e:28 > vge0: [ITHREAD] > -- Regards, Pyun YongHyeon _______________________________________________ freebsd-current@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?48a901c8949b$d88166e0$898434a0$>