Date: Tue, 10 May 2011 12:32:31 -0400 From: Mike Tancsa <mike@sentex.net> To: freebsd-usb@freebsd.org Subject: usb errors on RELENG_8 Message-ID: <4DC9689F.60506@sentex.net>
next in thread | raw e-mail | index | archive | help
I am trying to monitor a boat load of UPSes off a soekris 5501 (same error on an Alix box) and a pair of USB hubs. It seems I can only have one USB hub plug in at a time. If I plug just one in, all is ok. But if two are plugged in, I get a stream of errors like this. Is this some sort of device or driver limitation ? ugen1.11: <Unknown> at usbus1 (disconnected) uhub_reattach_port: could not allocate new device usb_alloc_device: set address 11 failed (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 11 failed, USB_ERR_STALLED usbd_req_re_enumerate: addr=11, set address failed! (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 11 failed, USB_ERR_STALLED usbd_req_re_enumerate: addr=11, set address failed! (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device descriptor at addr 11 failed, USB_ERR_STALLED ugen1.11: <Unknown> at usbus1 (disconnected) uhub_reattach_port: could not allocate new device ugen0.1: <OHCI root HUB AMD> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE ugen1.1: <EHCI root HUB AMD> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.2: <USB2.0 Hub vendor 0x05e3> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.3: <Back-UPS RS 1500 FW8.g7 .D USB FWg7 American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.4: <Back-UPS RS 1500 FW8.g8 .D USB FWg8 American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.5: <product 0xf103 vendor 0x2001> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.6: <Back-UPS RS 1500 FW8.g8 .D USB FWg8 American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.7: <Back-UPS RS 1500 FW8.g9a.D USB FWg9a American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.8: <Back-UPS RS 1500 FW8.g8 .D USB FWg8 American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.9: <Back-UPS RS 1500 FW8.g9a.D USB FWg9a American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen1.10: <Back-UPS RS 1500 FW8.g8 .D USB FWg8 American Power Conversion> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ---Mike -- ------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike@sentex.net Providing Internet services since 1994 www.sentex.net Cambridge, Ontario Canada http://www.tancsa.com/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4DC9689F.60506>