Date: Sat, 13 Jul 2019 20:49:56 +0200 From: Alex Samorukov <samm@net-art.cz> To: "freebsd-arm@freebsd.org" <freebsd-arm@freebsd.org> Subject: FreeBSD 11.3-R does not boot on RPi1 Message-ID: <57851faa-180b-8033-d29a-129776d2d1fa@net-art.cz>
next in thread | raw e-mail | index | archive | help
Hi. I tried today to boot 11.3 from the official image (FreeBSD-11.3-RELEASE-arm-armv6-RPI-B.img) and found that it does not work. I think it is a regression, as 11.2 boots on the same hw without any issues. I was using dd to put image to sd card. Bootlog is provided belowl Loading Environment from FAT... In: serial Out: vidconsole Err: vidconsole Net: No ethernet found. starting USB... USB0: scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 MMC Device 0 not found no mmc device at slot 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found U-Boot script /boot.scr 199 bytes read in 6 ms (32.2 KiB/s) ## Executing script at 02400000 285056 bytes read in 32 ms (8.5 MiB/s) ## Starting application at 0x00080000 ... Consoles: U-Boot console Compatible U-Boot API signature found @0x1bb40c80 FreeBSD/armv6 U-Boot loader, Revision 1.2 (Fri Jul 5 03:38:30 UTC 2019 root@releng2.nyi.freebsd.org) DRAM: 448MB Number of U-Boot devices: 1 U-Boot env: loaderdev not set, will probe all devices. Found U-Boot device: disk Probing all <unknown> devices... Checking unit=0 slice=<auto> partition=<auto>... good. Booting from disk0s2a: Loading /boot/defaults/loader.conf /boot/kernel/kernel data=0x6482ac+0x19fd54 syms=[0x4+0xaae80+0x4+0x98ff0] / Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... Using DTB provided by U-Boot at address 0x1bfea200. Kernel entry at 0x400100... Kernel args: (null) Copyright (c) 1992-2019 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.3-RELEASE #0 r349754: Fri Jul 5 03:51:28 UTC 2019 root@releng2.nyi.freebsd.org:/usr/obj/arm.armv6/usr/src/sys/RPI-B arm FreeBSD clang version 8.0.0 (tags/RELEASE_800/final 356365) (based on LLVM 8.0.0) VT: init without driver. CPU: ARM ARM1176 r0p7 (ECO: 0x00000000) CPU Features: Thumb, Security, VMSAv7 Optional instructions: UMULL, SMULL, MLA, SIMD(ext) 16KB/32B 4-way instruction cache 16KB/32B 4-way WB data cache real memory = 469757952 (447 MB) avail memory = 448118784 (427 MB) random: entropy device external interface kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> on ofwbus0 bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19 on simplebus0 bcm_dma0: cannot allocate interrupt device_attach: bcm_dma0 attach returned 6 bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on simplebus0 bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f irq 20 on simplebus0 mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 21 on simplebus0 mbox0: could not allocate interrupt resource device_attach: mbox0 attach returned 6 gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 22,23 on simplebus0 gpio0: cannot allocate resources gpio0: bcm_gpio_pic_detach: not implemented yet device_attach: gpio0 attach returned 6 uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 24 on simplebus0 uart0: console (115200,n,8,1) bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 45,46 on simplebus0 bcm283x_dwcotg0: failed to set power state, err=6 device_attach: bcm283x_dwcotg0 attach returned 6 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 48 on simplebus0 device_attach: sdhci_bcm0 attach returned 6 fb0: <BCM2835 VT framebuffer driver> on simplebus0 device_attach: fb0 attach returned 6 vchiq0: <BCM2835 VCHIQ> mem 0x7e00b840-0x7e00b84e irq 51 on simplebus0 vchiq0: could not allocate interrupt resource device_attach: vchiq0 attach returned 6 gpioled0: <GPIO LEDs> on ofwbus0 gpioled0: <led0> failed to map pin cryptosoft0: <software crypto> panic: No usable event timer found! Uptime: 1s Automatic reboot in 15 seconds - press a key on the console to abort Rebooting...
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?57851faa-180b-8033-d29a-129776d2d1fa>