Date: Mon, 11 Sep 2000 09:46:22 -0400 From: "Passki, Jonathan P" <jpasski@kpmg.com> To: "'Michael Slater'" <slaterm@enterprise.scom.net>, freebsd-questions@freebsd.org Subject: RE: bktr driver and fxtv Message-ID: <7799D023E51ED311BFB50008C75DD7B40223B24A@uschiexc05.kweb.us.kpmg.com>
next in thread | raw e-mail | index | archive | help
Hello Michael and all, I receive pretty much the same output/error after adding a STB TV Video PCI card to a 4.1 -S box, and recompiling. I haven't updated the source for about a week or two, but I hoped the bktr support hasn't changed that much since then. On a side note, after rebooting into W98 on the same box, and having all the other hardware installed, I installed the manufacture's drivers, and viola, the FM tuner part was recognized. FreeBSD could recognized the BrookTree chip, but it didn't recognized the tuner, which displays the PCI vendor code of BrookTree (0x109e = http://www.yourvote.com/pci/pciread.asp?venid=0x109E). I tried tweaking my kernel by looking at the source for bktr (/sys/dev/bktr I think, I'm at work right now...), but to no avail. I don't have a sound card currently installed (getting one soon, and paying OSS for the drivers), so I don't know if that's throwing the kernel off, but shouldn't this tuner get recognized properly? Jon -----Original Message----- From: Michael Slater [mailto:slaterm@enterprise.scom.net] Sent: Saturday, September 09, 2000 7:52 PM To: freebsd-questions@FreeBSD.ORG Subject: bkktr driver and fxtv Hi, I get the following error when i try to start fxtv No supported visual found.. this is the dmesg output, which indicated the card type cannot be determined.. bktr0: <BrookTree 878> mem 0xe7000000-0xe7000fff irq 11 at device 11.0 on pci0 iicbb0: <I2C generic bit-banging driver> on bti2c0 iicbus0: <Philips I2C bus> on iicbb0 master-only smbus0: <System Management Bus> on bti2c0 Card has no configuration EEPROM. Cannot determine card make. IMS TV Turbo, Philips FR1236 NTSC FM tuner. pci0: <unknown card> (vendor=0x109e, dev=0x0878) at 11.1 irq 11 As to the card type, it is just some generic card with a bt878 chip installed.. Under linux it gets detected as a Miro card... I tried to set the card type as Miro by sysctl -w hw.bt848.card=1, yet i still get the error message.. I'm trying to run it under vncserver, from a windows machine could this be the cause of the problem ? regards, Michael To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message ***************************************************************************** The information in this email is confidential and may be legally privileged. It is intended solely for the addressee. Access to this email by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. When addressed to our clients any opinions or advice contained in this email are subject to the terms and conditions expressed in the governing KPMG client engagement letter. ***************************************************************************** To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7799D023E51ED311BFB50008C75DD7B40223B24A>