Date: Wed, 4 Feb 1998 10:40:24 +0100 From: robin@obs-besancon.fr To: freebsd-questions@FreeBSD.ORG Cc: robin@obs-besancon.fr Subject: pccardd for pcmcia scsi card Adaptec APA-1460 SCSI Message-ID: <9802040940.AA15790@milan.obs-besancon.fr>
next in thread | raw e-mail | index | archive | help
Hi,
I encounter problems in configuring my machine with a pcmcia scsi adpater.
The card is referenced in the supported card but it does not seem to work.
My machine is an Olivetti ECHOS P90S.
The card is "APA-1460 SCSI Host Adapter" and is recognized by pccardd at the boot
but then I get the following message :
Feb 4 10:25:08 annie pccardd[34]: driver allocation failed for Adaptec, Inc. (Device not configured)
I have tried different config index port adress and irq's but with no result.
Contrarily to what is mentionned in the supported cards and pccard.conf by
default my card (as shown by pccardc dumpcis) should have an IRQ 4 or 5
(pccard.conf says IRQ 10).
If it helps this is the pccard dumpcis messages :
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 00 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 12 00 ff
Attribute memory device information:
Device number 1, type Mask ROM, WPS = OFF
Speed = 200nS, Memory block size = 512b, 1 units
Tuple #3, code = 0x15 (Version 1 info), length = 57
000: 04 01 41 64 61 70 74 65 63 2c 20 49 6e 63 2e 00
010: 41 50 41 2d 31 34 36 30 20 53 43 53 49 20 48 6f
020: 73 74 20 41 64 61 70 74 65 72 00 56 65 72 73 69
030: 6f 6e 20 30 2e 30 31 00 ff
Version = 4.1, Manuf = [Adaptec, Inc.],card vers = [APA-1460 SCSI Host Adapter]
Addit. info = [Version 0.01],[]
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: 2f 01 02 00
PCMCIA ID = 0x12f, OEM ID = 0x2
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 08 00 20 01
Reg len = 2, config register addr = 0x2000, last config = 0x8
Registers: X-------
Tuple #6, code = 0x1b (Configuration entry), length = 15
000: c9 01 19 49 55 65 06 ca 60 40 03 1f 30 00 1e
Config index = 0x9(default)
Interface byte = 0x1 (I/O)
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 6 x 10mA
Power down supply current: 1 x 100mA
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
IRQ modes: Level
IRQs: 4 5
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 08 08 ca 60 40 01 1f
Config index = 0x8
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x140 block length = 0x20
Tuple #8, code = 0x14 (No link), length = 0
Tuple #9, code = 0xff (Terminator), length = 0
Thanks for your help
Annie Robin
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?9802040940.AA15790>