Date: Sun, 13 Sep 2020 14:12:11 -0400 From: Anthony Jenkins <Scoobi_doo@yahoo.com> To: freebsd-wireless@freebsd.org Subject: Atheros QCA6174 (ath10k) not working Message-ID: <9beac50d-6c08-0c0a-7f42-f1e95ae31d8f@yahoo.com> References: <9beac50d-6c08-0c0a-7f42-f1e95ae31d8f.ref@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
I have a Killer 1535 802.11ac wireless card (chipset =3D Qualcomm Atheros= =20 QCA6174).=C2=A0 I am using the ath10k/athp driver from git repo=20 https://github.com/erikarn/athp.git .=C2=A0 Driver loads, but trying to s= tart=20 the interface fails.=C2=A0 What should I be looking at to fix this? service netif start wlan2: -------------------------------------------------------------------------= -- ifconfig: SIOCIFCREATE2: Input/output error ifconfig: interface wlan2 does not exist ifconfig: interface wlan2 does not exist ifconfig: interface wlan2 does not exist ifconfig: interface wlan2 does not exist Starting wpa_supplicant. /etc/rc.d/wpa_supplicant: WARNING: failed to start wpa_supplicant ifconfig: interface wlan2 does not exist rtsol: failed to get link layer information for wlan2 rtsol: failed to initialize wlan2 Starting Network: wlan2. ifconfig: interface wlan2 does not exist -------------------------------------------------------------------------= -- Kernel messages: -------------------------------------------------------------------------= -- athp0: ath10k_start: called; state=3D0 athp0: ath10k_start: state=3D1 athp0: ath10k_download_cal_dt: TODO: device tree check athp0: ath10k_wmi_event_service_ready_work: TODO: EEPROM code: 0x00000069= athp0: htc ep 2 out of TX credits (0 < 1) athp0: htc ep 2 out of TX credits (0 < 1) =2E.. athp0: htc ep 2 out of TX credits (0 < 1) athp0: htc ep 2 out of TX credits (0 < 1) athp0: ath10k_wmi_cmd_send: failed (-35) athp0: failed to enable PMF QOS: -35 athp0: ath10k_core_stop: state=3D1 athp0: ath10k_wait_for_suspend: state=3D1 athp0: ath10k_wmi_pdev_suspend_target: called athp0: htc ep 2 out of TX credits (0 < 1) athp0: htc ep 2 out of TX credits (0 < 1) =2E.. athp0: htc ep 2 out of TX credits (0 < 1) athp0: htc ep 2 out of TX credits (0 < 1) athp0: ath10k_wmi_cmd_send: failed (-35) athp0: could not suspend target (-35) athp0: ath10k_pci_irq_sync: TODO athp0: ath10k_pci_kill_tasklet: called athp0: ath10k_htt_tx_free: called athp0: ath10k_htt_tx_free: tearing down htt locks athp0: athp_vap_create: ath10k_start failed; ret=3D-35 -------------------------------------------------------------------------= -- Some notable errors from 'kldload if_athp.ko': * Driver fails to load firmware file athp_QCA6174_hw3.0/firmware-5.bin;=20 it does load file 'athp_QCA6174_hw3.0_firmware-4.bin'. athp0: ath10k_fetch_fw_file: firmware_get: athp_cal-pci-athp0.bin athp_cal-pci-athp0.bin: could not load firmware image, error 2 athp0: ath10k_fetch_fw_file: firmware_get: athp_QCA6174_hw3.0_board.bin firmware: 'athp_QCA6174_hw3.0_board.bin' version 1: 8124 bytes loaded at = 0xffffffff84458000 athp0: ath10k_fetch_fw_file: firmware_get: athp_QCA6174_hw3.0_firmware-5.= bin athp_QCA6174_hw3.0_firmware-5.bin: could not load firmware image, error 2= athp0: could not fetch firmware file 'athp_QCA6174_hw3.0/firmware-5.bin':= -1 athp0: ath10k_fetch_fw_file: firmware_get: athp_QCA6174_hw3.0_firmware-4.= bin firmware: 'athp_QCA6174_hw3.0_firmware-4.bin' version 1: 733784 bytes=20 loaded at 0xffffffff8445d000 I assume file 'athp_cal-pci-athp0.bin' is optional calibration data. * 'htc ep 2 out of TX credits (0 < 1)' repeated 144 times * ath10k_wmi_cmd_send failure athp0: ath10k_wmi_cmd_send: failed (-35) athp0: could not suspend target (-35) My full kernel messages from kldload(8) and netif are at=20 http://www.qtchat.org/~ajenkins/ . Thanks, Anthony Jenkins
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?9beac50d-6c08-0c0a-7f42-f1e95ae31d8f>