Date: Sat, 13 Jan 2024 20:22:07 +0100 From: Jesper Schmitz Mouridsen <jsm@FreeBSD.org> To: Mark Millard <marklmi@yahoo.com>, Doug Rabson <dfr@rabson.org> Cc: John Kennedy <warlock@phouka.net>, ykla <yklaxds@gmail.com>, FreeBSD ARM List <freebsd-arm@freebsd.org> Subject: Re: When will FreeBSD support RPI5? Message-ID: <9e45c7d7-450c-48e5-8101-c6ea5cb3a023@FreeBSD.org> In-Reply-To: <76FA010A-338F-4E32-B381-37C7BA63CAFC@yahoo.com> References: <CA%2BPGaYC6__AZUgHqfv3PO-o=7FnEzRzTPGPhMuahFNdcN0D69A@mail.gmail.com> <ddbf131c-1f2c-424b-9a3f-54ded16c5123@FreeBSD.org> <ZZHC_SjrPgs3DMKe@phouka1.phouka.net> <5a39810c-5fd8-4969-a222-2561b050b035@FreeBSD.org> <CACA0VUjoTTVje7tQe%2BVHXPco_xs4C8vSB3P3eDnhuYJYSqc7Sw@mail.gmail.com> <A2CA16F2-9894-41F2-8035-A5E8BE271B58@yahoo.com> <CACA0VUg7XHtQ7nviXVUZ_dZGaPe2uhbT-eGRbMAOajqZLGDmew@mail.gmail.com> <ECBFBAEF-C35B-4C68-B9BF-C3B62E5A4DFE@yahoo.com> <347FE009-A470-4765-A9B9-7C9AB5E954DA@yahoo.com> <CACA0VUh_X5nudWGOCeupW_34=aUewmwvOWmp61ONm=PtNr9wFw@mail.gmail.com> <76FA010A-338F-4E32-B381-37C7BA63CAFC@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 13.01.2024 19.32, Mark Millard wrote: > On Jan 13, 2024, at 07:38, Doug Rabson <dfr@rabson.org> wrote: > >> Getting back to the RPI 5, with a tweak to arm/broadcom/bcm2835bcm2835_vcbus.c to treat the memory config the same as RPI 4 and to dev/sdhci/sdhci_fdt.c to treat the RPI 5 sdhci controllers as generic, I can boot to multiuser mode using the EDK2 firmware from https://github.com/worproject/rpi5-uefi with ACPI/Device Tree mode set to Both. > What does FreeBSD do with "Both"? Does it actually use some ACPI > and some Device Tree? Or does it just use ACPI? Does your > combination do anything different than just using ACPI? How does the sd card show up? BTW i did put some stuff here [1] I could not get bcm_dma to work anyone planning on getting that to work? it should be similar to 2711 documented in [2] >> This does not have working PCIe or ethernet yet - I think ethernet ought to work since we seem to have a matching driver in the tree in dev/cadence. > Sounds like the same status as booting just ACPI with no such > adjustments too bcm2835bcm2835_vcbus.c or sdhci_fdt.c ? > > I think Mike Karels plans on investigating getting Ethernet > going based on cgem . I've no clue if this is ACPI, DeviceTree, > or both. > > My usage has been pure ACPI, no software adjustments specific > to getting the RPi5 operational. Use of a USB3 Ethernet dongle. > > === > Mark Millard > marklmi at yahoo.com > > [1] https://github.com/jsm222/rpi5-stuff [2] https://datasheets.raspberrypi.com/bcm2711/bcm2711-peripherals.pdf
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?9e45c7d7-450c-48e5-8101-c6ea5cb3a023>