Date: Thu, 7 Oct 2010 16:04:56 +0000 From: Paul B Mahol <onemda@gmail.com> To: Eitan Adler <lists@eitanadler.com> Cc: FreeBSD Mailing List <freebsd-questions@freebsd.org> Subject: Re: if_bwn woes Message-ID: <AANLkTi=-8Uwd9e2V%2BUfCX6LCKzYQVRfqhyJ6r8VpwOg2@mail.gmail.com> In-Reply-To: <AANLkTikxTUZ5JBRSL_xrTBEoU8giO43vBJp4p1KVLNe7@mail.gmail.com> References: <AANLkTintgXLf2cRrY5TU=piCYZke6y8audE_WJXsdoTZ@mail.gmail.com> <AANLkTikpghsUJbCZ%2B8yc1oWMJFfs0KH9-gSqA-80n-nM@mail.gmail.com> <AANLkTimVSfWnv_dTWJtKreti2SerngycKnpxFkweUDAM@mail.gmail.com> <AANLkTinuNhr=y=r_ud-w1gY_B_um_gfvZA8xpqfzKdaD@mail.gmail.com> <AANLkTikxTUZ5JBRSL_xrTBEoU8giO43vBJp4p1KVLNe7@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 10/7/10, Eitan Adler <lists@eitanadler.com> wrote: > On Thu, Oct 7, 2010 at 2:31 PM, Paul B Mahol <onemda@gmail.com> wrote: >> On 10/7/10, Eitan Adler <lists@eitanadler.com> wrote: >>>>> >>>>> ifconfig wlan0 scan results in no output and takes forever (ie - it >>>>> hangs) >>>> If you set wlan0 for manual roaming it will not hang. >>>> >>>> Use 'ifconfig wlan0 list scan' instead. >>> That worked, thanks. >>> >>> dhclient still results in no link being found. >> >> Are you sure that you setup is correct? >> For example you can not connect to AP which require RSN authmode >> if you configure wlan0 for OPEN authmode, you also may not >> connect to AP if you are far away, because you are able >> to receive and send doesn't mean AP can see your packets ........ >> >> Try changing ucastrate to lower values. >> > > I'm not really sure what ucastrate does - but here it goes: > > $ifconfig wlan0 list scan|head -1 > xyz 00:23:xx:yy:zz:aa:bb 1 54M -125:-95 102 E HTCAP WME > $ifconfig wlan0 ssid xyz > $dhclient wlan0 > ... no link ... > $ifconfig wlan0 ucastrate 9 > $dhclient wlan0 > ... no link ... > $ifconfig wlan0 ucastrate 1 > $dhclient wlan0 > ... no link ... > > I'm fairly sure that I'm in an area where the signal reaches because > when I was using the ndis driver (on an old install) it worked. > This is a fresh install now. Looks like you cant associate at all. Also signal power is too low. Why is INT (beacon interval of AP) 102 ?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?AANLkTi=-8Uwd9e2V%2BUfCX6LCKzYQVRfqhyJ6r8VpwOg2>