Date: Sat, 29 May 2010 21:46:34 -0700 From: Garrett Cooper <yanefbsd@gmail.com> To: Wei Yang Tan <hallucinator7@hotmail.com> Cc: freebsd-acpi@freebsd.org Subject: Re: Errors encountered when performing hibernate / suspend Message-ID: <AANLkTimdYq5WO6TxF7sfWfuQb8f1gdS5rZc3pa-lzQ0A@mail.gmail.com> In-Reply-To: <COL115-W3908B9EBA073CCC13E4943E8ED0@phx.gbl> References: <COL115-W3908B9EBA073CCC13E4943E8ED0@phx.gbl>
next in thread | previous in thread | raw e-mail | index | archive | help
2010/5/29 Wei Yang Tan <hallucinator7@hotmail.com>: > >> From: hallucinator7@hotmail.com >> To: freebsd-acpi@freebsd.org >> Date: Thu, 13 May 2010 21:56:20 +0800 >> Subject: Errors encountered when performing hibernate / suspend >> >> >> Hi! >> >> >> First, thank you very much for your help. I am very new to FreeBSD, so d= o bear with me for a while. Anyway, the problem is as follows: >> >> >> Whenever I tried to hibernate, it will not be successful and I get the f= ollowing error at my ~/.xession-error file: >> >> >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> >> ** (xfce4-session:1124): WARNING **: xfsm-shutdown-helper.c:234: Failed = to contact HAL: No back-end for your operating system >> >> >> >> When I tried to suspend, it will not be successful and I will get the er= ror message at my ~/.xession-error file: >> >> >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> thunar-volman: No property info.capabilities on device with id /org/free= desktop/Hal/devices/usb_device_45e_83_noserial. >> >> >> >> I read the Handbook and I thought it may help by trying out the command = "acpiconf -s1". Of course it is not successful and the error message ar ~/.= xsession-error is: >> >> >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> ** Message: xfsm-shutdown-helper.c:268: Using HAL to shutdown/reboot the= computer. >> thunar-volman: No property info.capabilities on device with id /org/free= desktop/Hal/devices/usb_device_45e_83_noserial. >> >> >> >> >> while the following is my "dmesg" output: >> >> >> Copyright (c) 1992-2009 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> =A0 =A0 =A0 The Regents of the University of California. All rights rese= rved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:48:17 UTC 2009 >> =A0 =A0 root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> CPU: Intel Pentium III (996.77-MHz 686-class CPU) >> =A0 Origin =3D "GenuineIntel" =A0Id =3D 0x68a =A0Stepping =3D 10 >> =A0 Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTR= R,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> >> real memory =A0=3D 537395200 (512 MB) >> avail memory =3D 510431232 (486 MB) >> ACPI APIC Table: <COMPAQ SOLANO =A0> >> ioapic0: Changing APIC ID to 8 >> ioapic0 <Version 2.0> irqs 0-23 on motherboard >> kbd1 at kbdmux0 >> acpi0: <COMPAQ CPQ0005> on motherboard >> acpi0: [ITHREAD] >> acpi0: Power Button (fixed) >> acpi0: reservation of 0, a0000 (3) failed >> acpi0: reservation of 100000, 1ff00000 (3) failed >> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 >> acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf808-0xf80b on acpi0 >> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >> pci0: <ACPI PCI bus> on pcib0 >> agp0: <Intel 82815 (i815 GMCH) host to PCI bridge> on hostb0 >> pcib1: <PCI-PCI bridge> at device 1.0 on pci0 >> pci1: <PCI bus> on pcib1 >> vgapci0: <VGA-compatible display> mem 0x41000000-0x41ffffff,0x44000000-0= x45ffffff irq 18 at device 0.0 on pci1 >> pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 >> pci2: <ACPI PCI bus> on pcib2 >> fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0x1000-0x103f m= em 0x40000000-0x40000fff irq 20 at device 8.0 on pci2 >> miibus0: <MII bus> on fxp0 >> inphy0: <i82562EM 10/100 media interface> PHY 1 on miibus0 >> inphy0: =A010baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> fxp0: Ethernet address: 00:02:a5:94:97:26 >> fxp0: [ITHREAD] >> isab0: <PCI-ISA bridge> at device 31.0 on pci0 >> isa0: <ISA bus> on isab0 >> atapci0: <Intel ICH2 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x= 177,0x376,0x2460-0x246f at device 31.1 on pci0 >> ata0: <ATA channel 0> on atapci0 >> ata0: [ITHREAD] >> ata1: <ATA channel 1> on atapci0 >> ata1: [ITHREAD] >> uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x2440-0x245= f irq 23 at device 31.4 on pci0 >> uhci0: [ITHREAD] >> uhci0: LegSup =3D 0x0030 >> usbus0: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci0 >> pcm0: <Intel ICH2 (82801BA)> port 0x2000-0x20ff,0x2400-0x243f irq 17 at = device 31.5 on pci0 >> pcm0: [ITHREAD] >> pcm0: <Analog Devices AD1885 AC97 Codec> >> acpi_button0: <Power Button> on acpi0 >> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 >> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> kbd0 at atkbd0 >> atkbd0: [GIANT-LOCKED] >> atkbd0: [ITHREAD] >> ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77d irq 7 drq 3 on acpi0 >> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode >> ppc0: FIFO with 16/16/13 bytes threshold >> ppc0: [ITHREAD] >> ppbus0: <Parallel port bus> on ppc0 >> ppbus0: IEEE1284 device found /NIBBLE >> ppbus0: Probing for PnP devices: >> ppbus0: <Canon S400SP/1.06> PRINTER BJL,BJRaster3,BSCC,TXT01,BJScan2 >> plip0: <PLIP network interface> on ppbus0 >> plip0: [ITHREAD] >> lpt0: <Printer> on ppbus0 >> lpt0: [ITHREAD] >> lpt0: Interrupt-driven port >> ppi0: <Parallel I/O> on ppbus0 >> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 >> uart0: [FILTER] >> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 >> uart1: [FILTER] >> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on ac= pi0 >> fdc0: [FILTER] >> fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >> cpu0: <ACPI CPU> on acpi0 >> acpi_throttle0: <ACPI CPU Throttling> on cpu0 >> pmtimer0 on isa0 >> orm0: <ISA Option ROM> at iomem 0xe0000-0xeffff pnpid ORM0000 on isa0 >> sc0: <System console> at flags 0x100 on isa0 >> sc0: VGA <16 virtual consoles, flags=3D0x300> >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa= 0 >> Timecounter "TSC" frequency 996770364 Hz quality 800 >> Timecounters tick every 1.000 msec >> usbus0: 12Mbps Full Speed USB v1.0 >> ad0: 39205MB <Maxtor 6E040L0 NAR61HA0> at ata0-master UDMA100 >> ugen0.1: <Intel> at usbus0 >> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 >> acd0: CDROM <LTN486S/YQS8> at ata1-master PIO4 >> pcm0: measured ac97 link rate at 55945 Hz >> uhub0: 2 ports with 2 removable, self powered >> Root mount waiting for: usbus0 >> ugen0.2: <Microsoft> at usbus0 >> ums0: <Microsoft Basic Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> = on usbus0 >> ums0: 3 buttons and [XYZ] coordinates ID=3D0 >> Trying to mount root from ufs:/dev/ad0s1a >> acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=3D0x64 ascq=3D0x00 >> acd0: FAILURE - unknown CMD (0x03) ILLEGAL REQUEST asc=3D0x20 ascq=3D0x0= 0 >> acd0: FAILURE - READ_DISK_INFO ILLEGAL REQUEST asc=3D0x20 ascq=3D0x00 >> acd0: FAILURE - READ_DISK_INFO ILLEGAL REQUEST asc=3D0x20 ascq=3D0x00 >> acpi0: AcpiEnterSleepState failed - AE_BAD_ADDRESS >> wakeup from sleeping state (slept 00:00:03) >> ugen0.2: <Microsoft> at usbus0 (disconnected) >> ums0: at uhub0, port 2, addr 2 (disconnected) >> ugen0.2: <Microsoft> at usbus0 >> ums0: <Microsoft Basic Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> = on usbus0 >> ums0: 3 buttons and [XYZ] coordinates ID=3D0 >> >> >> >> >> >> The output of "sysctl hw.acpi": >> >> >> hw.acpi.supported_sleep_state: S1 S3 S4 S5 >> hw.acpi.power_button_state: S5 >> hw.acpi.sleep_button_state: S1 >> hw.acpi.lid_switch_state: NONE >> hw.acpi.standby_state: S1 >> hw.acpi.suspend_state: S3 >> hw.acpi.sleep_delay: 1 >> hw.acpi.s4bios: 0 >> hw.acpi.verbose: 0 >> hw.acpi.disable_on_reboot: 0 >> hw.acpi.handle_reboot: 0 >> hw.acpi.reset_video: 0 >> hw.acpi.cpu.cx_lowest: C1 >> >> >> >> >> >> I am using FreeBSD 8.0 and Xfce desktop environment (Thunar is the file = manager). For hardware, I am using Pentium III; Compaq Deskpro EN. >> >> I am not sure if all these information are sufficient; do let me know if= you need more information. Once again, thank you very much for your help. > > Hi! Erm... just wondering, is my debug info sufficient or is the problem = not an ACPI one? Also, may I know what can I do to help in solving the prob= lem? Does ACPI even work on your laptop (try reading the handbook chapter: http://www.freebsd.org/doc/handbook/acpi-debug.html )? HTH, -Garrett
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?AANLkTimdYq5WO6TxF7sfWfuQb8f1gdS5rZc3pa-lzQ0A>