Date: Thu, 12 May 2011 15:17:09 -0400 From: Dillin Smith <dilli.ns.mith@gmail.com> To: freebsd-questions@freebsd.org Subject: Hard drive detection Message-ID: <BANLkTinHmEi7RL%2BatYQKUgVaYe9zuvjpjg@mail.gmail.com> In-Reply-To: <BANLkTi=7QO8p--mfCvugptxCcugRozTKTQ@mail.gmail.com> References: <BANLkTi=7QO8p--mfCvugptxCcugRozTKTQ@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hi all,
I'm having an issue getting my installation of FreeBSD to detect all the
drives in the system. It has 48 total, 46 2TB, and 2 250GB. The system
consists of six controllers, with eight drives on each. The two 250GB hard
drives are the first drives on controllers 0 and 1.
There are two of these machines with the exact same configurations, having
the same problem. A very odd thing is that every time the systems are
rebooted, the drives that go undetected vary. Also, when the systems were
full of 250GB drives, all were detected. All drives are detected in the BIOS
of the controllers, just not by FreeBSD.
Any and all help is greatly appreciated.
(output of dmesg attached)
[-- Attachment #2 --]
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-STABLE #0: Wed May 11 16:10:08 EDT 2011
root@bobo.earlham.edu:/usr/obj/usr/src/sys/GENERIC amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Quad-Core AMD Opteron(tm) Processor 2356 (2300.11-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x100f23 Family = 10 Model = 2 Stepping = 3
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x802009<SSE3,MON,CX16,POPCNT>
AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
AMD Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS>
TSC: P-state invariant
real memory = 34359738368 (32768 MB)
avail memory = 33110417408 (31576 MB)
ACPI APIC Table: <SUN X4540 >
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 2 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-47 on motherboard
ioapic2 <Version 1.1> irqs 48-71 on motherboard
kbd1 at kbdmux0
acpi0: <SUN X4540> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
unknown: I/O range not supported
acpi0: reservation of fec00000, 1000 (3) failed
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, ddf00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe008-0xe00b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> port 0xef00-0xef7f at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <nVidia nForce MCP55 USB Controller> mem 0xde7ff000-0xde7fffff irq 21 at device 2.0 on pci0
ohci0: [ITHREAD]
usbus0: <nVidia nForce MCP55 USB Controller> on ohci0
ehci0: <NVIDIA nForce MCP55 USB 2.0 controller> mem 0xde7fec00-0xde7fecff irq 22 at device 2.1 on pci0
ehci0: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <NVIDIA nForce MCP55 USB 2.0 controller> on ehci0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xac00-0xac7f mem 0xde800000-0xdeffffff,0xdf3e0000-0xdf3fffff irq 16 at device 5.0 on pci1
nfe0: <NVIDIA nForce MCP55 Networking Adapter> port 0x9480-0x9487 mem 0xde7fd000-0xde7fdfff,0xde7fe800-0xde7fe8ff,0xde7fe400-0xde7fe40f irq 23 at device 8.0 on pci0
miibus0: <MII bus> on nfe0
e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 2 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
nfe0: Ethernet address: 00:14:4f:f2:a6:90
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe1: <NVIDIA nForce MCP55 Networking Adapter> port 0x9400-0x9407 mem 0xde7fc000-0xde7fcfff,0xde7fe000-0xde7fe0ff,0xde7f7c00-0xde7f7c0f irq 20 at device 9.0 on pci0
miibus1: <MII bus> on nfe1
e1000phy1: <Marvell 88E1149 Gigabit PHY> PHY 3 on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
nfe1: Ethernet address: 00:14:4f:f2:a6:91
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
mpt0: <LSILogic SAS/SATA Adapter> port 0xb800-0xb8ff mem 0xdf7fc000-0xdf7fffff,0xdf7e0000-0xdf7effff irq 17 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.16.0
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
mpt1: <LSILogic SAS/SATA Adapter> port 0xc800-0xc8ff mem 0xdfbfc000-0xdfbfffff,0xdfbe0000-0xdfbeffff irq 18 at device 0.0 on pci3
mpt1: [ITHREAD]
mpt1: MPI Version=1.5.16.0
pcib4: <ACPI PCI-PCI bridge> at device 15.0 on pci0
pci4: <ACPI PCI bus> on pcib4
mpt2: <LSILogic SAS/SATA Adapter> port 0xd800-0xd8ff mem 0xdfffc000-0xdfffffff,0xdffe0000-0xdffeffff irq 18 at device 0.0 on pci4
mpt2: [ITHREAD]
mpt2: MPI Version=1.5.16.0
pcib5: <ACPI Host-PCI bridge> on acpi0
pci64: <ACPI PCI bus> on pcib5
pci64: <memory, RAM> at device 0.0 (no driver attached)
pci64: <memory, RAM> at device 1.0 (no driver attached)
pci64: <serial bus, SMBus> at device 1.1 (no driver attached)
nfe2: <NVIDIA nForce MCP55 Networking Adapter> port 0x5400-0x5407 mem 0xdd3fe000-0xdd3fefff,0xdd3fdc00-0xdd3fdcff,0xdd3fd800-0xdd3fd80f irq 45 at device 8.0 on pci64
miibus2: <MII bus> on nfe2
e1000phy2: <Marvell 88E1149 Gigabit PHY> PHY 2 on miibus2
e1000phy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
nfe2: Ethernet address: 00:14:4f:f2:a6:92
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe2: [FILTER]
nfe3: <NVIDIA nForce MCP55 Networking Adapter> port 0x5080-0x5087 mem 0xdd3fc000-0xdd3fcfff,0xdd3fd400-0xdd3fd4ff,0xdd3fd000-0xdd3fd00f irq 46 at device 9.0 on pci64
miibus3: <MII bus> on nfe3
e1000phy3: <Marvell 88E1149 Gigabit PHY> PHY 3 on miibus3
e1000phy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
nfe3: Ethernet address: 00:14:4f:f2:a6:93
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
nfe3: [FILTER]
pcib6: <ACPI PCI-PCI bridge> at device 10.0 on pci64
pci65: <ACPI PCI bus> on pcib6
mpt3: <LSILogic SAS/SATA Adapter> port 0x6800-0x68ff mem 0xdd7fc000-0xdd7fffff,0xdd7e0000-0xdd7effff irq 40 at device 0.0 on pci65
mpt3: [ITHREAD]
mpt3: MPI Version=1.5.16.0
pcib7: <ACPI PCI-PCI bridge> at device 11.0 on pci64
pci66: <ACPI PCI bus> on pcib7
mpt4: <LSILogic SAS/SATA Adapter> port 0x7800-0x78ff mem 0xddbfc000-0xddbfffff,0xddbe0000-0xddbeffff irq 41 at device 0.0 on pci66
mpt4: [ITHREAD]
mpt4: MPI Version=1.5.16.0
pcib8: <ACPI PCI-PCI bridge> at device 15.0 on pci64
pci67: <ACPI PCI bus> on pcib8
mpt5: <LSILogic SAS/SATA Adapter> port 0x8800-0x88ff mem 0xddffc000-0xddffffff,0xddfe0000-0xddfeffff irq 41 at device 0.0 on pci67
mpt5: [ITHREAD]
mpt5: MPI Version=1.5.16.0
pcib9: <ACPI Host-PCI bridge> on acpi0
pci128: <ACPI PCI bus> on pcib9
pci128: <memory, RAM> at device 0.0 (no driver attached)
pci128: <memory, RAM> at device 1.0 (no driver attached)
pci128: <serial bus, SMBus> at device 1.1 (no driver attached)
pcib10: <ACPI PCI-PCI bridge> at device 10.0 on pci128
pci129: <ACPI PCI bus> on pcib10
pcib11: <ACPI PCI-PCI bridge> at device 11.0 on pci128
pci130: <ACPI PCI bus> on pcib11
pcib12: <ACPI PCI-PCI bridge> at device 15.0 on pci128
pci131: <ACPI PCI bus> on pcib12
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed00fff on acpi0
Timecounter "HPET" frequency 25000000 Hz quality 900
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xce000-0xcf7ff on isa0
atkbd: unable to set the command byte.
sc0: <System console> at flags 0x100 on isa0
sc0: CGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3d0-0x3db iomem 0xb8000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to set the command byte.
ppc0: cannot reserve I/O port range
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <nVidia> at usbus0
uhub0: <nVidia OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <nVidia> at usbus1
uhub1: <nVidia EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub0: 10 ports with 10 removable, self powered
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <ATA SEAGATE ST32502N SU0D> Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 238471MB (488390625 512 byte sectors: 255H 63S/T 30400C)
da1 at mpt0 bus 0 scbus0 target 1 lun 0
da1: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da1: 300.000MB/s transfers
da1: Command Queueing enabled
da1: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da2 at mpt0 bus 0 scbus0 target 2 lun 0
da2: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da2: 300.000MB/s transfers
da2: Command Queueing enabled
da2: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da3 at mpt0 bus 0 scbus0 target 3 lun 0
da3: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da3: 300.000MB/s transfers
da3: Command Queueing enabled
da3: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da7 at mpt1 bus 0 scbus1 target 0 lun 0
da7: <ATA SEAGATE ST32502N SU0D> Fixed Direct Access SCSI-5 device
da7: 300.000MB/s transfers
da7: Command Queueing enabled
da7: 238471MB (488390625 512 byte sectors: 255H 63S/T 30400C)
da4 at mpt0 bus 0 scbus0 target 4 lun 0
da4: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da4: 300.000MB/s transfers
da4: Command Queueing enabled
da4: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da5 at mpt0 bus 0 scbus0 target 5 lun 0
da5: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da5: 300.000MB/s transfers
da5: Command Queueing enabled
da5: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da6 at mpt0 bus 0 scbus0 target 6 lun 0
da6: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da6: 300.000MB/s transfers
da6: Command Queueing enabled
da6: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da8 at mpt1 bus 0 scbus1 target 1 lun 0
da8: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da8: 300.000MB/s transfers
da8: Command Queueing enabled
da8: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da9 at mpt1 bus 0 scbus1 target 2 lun 0
da9: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da9: 300.000MB/s transfers
da9: Command Queueing enabled
da9: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da10 at mpt1 bus 0 scbus1 target 3 lun 0
da10: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da10: 300.000MB/s transfers
da10: Command Queueing enabled
da10: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da11 at mpt1 bus 0 scbus1 target 4 lun 0
da11: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da11: 300.000MB/s transfers
da11: Command Queueing enabled
da11: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da12 at mpt1 bus 0 scbus1 target 5 lun 0
da12: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da12: 300.000MB/s transfers
da12: Command Queueing enabled
da12: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da13 at mpt1 bus 0 scbus1 target 6 lun 0
da13: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da13: 300.000MB/s transfers
da13: Command Queueing enabled
da13: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da14 at mpt1 bus 0 scbus1 target 7 lun 0
da14: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da14: 300.000MB/s transfers
da14: Command Queueing enabled
da14: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da15 at mpt2 bus 0 scbus2 target 2 lun 0
da15: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da15: 300.000MB/s transfers
da15: Command Queueing enabled
da15: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da16 at mpt2 bus 0 scbus2 target 3 lun 0
da16: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da16: 300.000MB/s transfers
da16: Command Queueing enabled
da16: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da17 at mpt2 bus 0 scbus2 target 4 lun 0
da17: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da17: 300.000MB/s transfers
da17: Command Queueing enabled
da17: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da18 at mpt2 bus 0 scbus2 target 5 lun 0
da18: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da18: 300.000MB/s transfers
da18: Command Queueing enabled
da18: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da19 at mpt2 bus 0 scbus2 target 6 lun 0
da19: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da19: 300.000MB/s transfers
da19: Command Queueing enabled
da19: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da21 at mpt3 bus 0 scbus3 target 0 lun 0
da21: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da21: 300.000MB/s transfers
da21: Command Queueing enabled
da21: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da22 at mpt3 bus 0 scbus3 target 1 lun 0
da22: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da22: 300.000MB/s transfers
da22: Command Queueing enabled
da22: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da20 at mpt2 bus 0 scbus2 target 7 lun 0
da20: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da20: 300.000MB/s transfers
da20: Command Queueing enabled
da20: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da23 at mpt3 bus 0 scbus3 target 2 lun 0
da23: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da23: 300.000MB/s transfers
da23: Command Queueing enabled
da23: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da24 at mpt3 bus 0 scbus3 target 3 lun 0
da24: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da24: 300.000MB/s transfers
da24: Command Queueing enabled
da24: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da25 at mpt3 bus 0 scbus3 target 4 lun 0
da25: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da25: 300.000MB/s transfers
da25: Command Queueing enabled
da25: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da26 at mpt3 bus 0 scbus3 target 5 lun 0
da26: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da26: 300.000MB/s transfers
da26: Command Queueing enabled
da26: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da27 at mpt3 bus 0 scbus3 target 6 lun 0
da27: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da27: 300.000MB/s transfers
da27: Command Queueing enabled
da27: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da28 at mpt4 bus 0 scbus4 target 0 lun 0
da28: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da28: 300.000MB/s transfers
da28: Command Queueing enabled
da28: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da29 at mpt4 bus 0 scbus4 target 2 lun 0
da29: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da29: 300.000MB/s transfers
da29: Command Queueing enabled
da29: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da30 at mpt4 bus 0 scbus4 target 3 lun 0
da30: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da30: 300.000MB/s transfers
da30: Command Queueing enabled
da30: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da31 at mpt4 bus 0 scbus4 target 4 lun 0
da31: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da31: 300.000MB/s transfers
da31: Command Queueing enabled
da31: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da32 at mpt4 bus 0 scbus4 target 5 lun 0
da32: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da32: 300.000MB/s transfers
da32: Command Queueing enabled
da32: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da33 at mpt4 bus 0 scbus4 target 6 lun 0
da33: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da33: 300.000MB/s transfers
da33: Command Queueing enabled
da33: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da34 at mpt4 bus 0 scbus4 target 7 lun 0
da34: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da34: 300.000MB/s transfers
da34: Command Queueing enabled
da34: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da35 at mpt5 bus 0 scbus5 target 0 lun 0
da35: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da35: 300.000MB/s transfers
da35: Command Queueing enabled
da35: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da36 at mpt5 bus 0 scbus5 target 1 lun 0
da36: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da36: 300.000MB/s transfers
da36: Command Queueing enabled
da36: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da37 at mpt5 bus 0 scbus5 target 2 lun 0
da37: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da37: 300.000MB/s transfers
da37: Command Queueing enabled
da37: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da38 at mpt5 bus 0 scbus5 target 4 lun 0
da38: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da38: 300.000MB/s transfers
da38: Command Queueing enabled
da38: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da39 at mpt5 bus 0 scbus5 target 6 lun 0
da39: <ATA Hitachi HDS72302 A180> Fixed Direct Access SCSI-5 device
da39: 300.000MB/s transfers
da39: Command Queueing enabled
da39: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
SMP: AP CPU #4 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #5 Launched!
uhub1: 10 ports with 10 removable, self powered
ugen0.2: <Dell> at usbus0
uhub2: <Dell USB Keyboard Hub> on usbus0
ugen1.2: <vendor 0x04b4> at usbus1
uhub3: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 2> on usbus1
uhub2: 3 ports with 2 removable, bus powered
ugen0.3: <Dell> at usbus0
ukbd0: <Dell USB Keyboard> on usbus0
kbd2 at ukbd0
uhub3: 4 ports with 4 removable, self powered
uhid0: <Dell USB Keyboard> on usbus0
Trying to mount root from ufs:/dev/da0s1a
ugen0.4: <Logitech> at usbus0
ums0: <Logitech Optical USB Mouse, class 0/0, rev 2.00/3.40, addr 4> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=0
WARNING: reducing size to maximum of 67108864 blocks per swap unit
ugen0.5: <American Megatrends Inc.> at usbus0
ukbd1: <Keyboard Interface> on usbus0
kbd3 at ukbd1
ums1: <Mouse Interface> on usbus0
IP Filter: v4.1.28 initialized. Default = pass all, Logging = enabled
nfe0: link state changed to UP
mpt5: mpt_cam_event: 0x16
mpt5: mpt_cam_event: 0x12
mpt5: mpt_cam_event: 0x16
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BANLkTinHmEi7RL%2BatYQKUgVaYe9zuvjpjg>