Date: Sun, 8 Mar 2015 23:06:15 +0530 From: Manish Jain <bourne.identity@hotmail.com> To: CyberLeo Kitsana <cyberleo@cyberleo.net> Cc: freebsd-questions@freebsd.org Subject: Re: Is there any plan to adopt devtmpfs ? Message-ID: <BLU436-SMTP146AB4D040B70CC68410BA2F61A0@phx.gbl> In-Reply-To: <BLU436-SMTP74AE6E33F834A2D406AE1BF61C0@phx.gbl> References: <BLU436-SMTP37B91369BA1F4532599758F61F0@phx.gbl> <54F88D64.4000607@cyberleo.net> <BLU436-SMTP74AE6E33F834A2D406AE1BF61C0@phx.gbl>
next in thread | previous in thread | raw e-mail | index | archive | help
On 03/06/2015 13:58, Manish Jain wrote:>>> Can you provide further
details for these failures? Specific device
>>> models and relevant dmesg(8) and usbconfig(8) output, for example.
>>>
>
> I have something for the APC UPS (USB Powerchute) too. Again, the
> complete output of dmesg is attached below my signature.
>
> 1)
> Important lines from my /etc/rc.conf :
>
> apcupsd_enable="NO" #Needed to run apctest
> dbus_enable="YES"
> hald_enable="YES"
> devfs_system_ruleset="system"
>
>
> 2)
> Important lines from my /usr/local/etc/apcupsd/apcupsd.conf :
>
> UPSNAME APC700BE
> UPSCABLE usb
> UPSTYPE usb
> DEVICE
> BATTERYLEVEL 5
> MINUTES 5
> UPSCLASS standalone
> UPSNAME APC700BE
> BATTDATE 05/28/14
> SENSITIVITY L
>
>
> 3)
> usbconfig -u 2 dump_info
> ugen2.1: <EHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps)
> pwr=SAVE (0mA)
>
> ugen2.2: <USB 2.0 Hub vendor 0x1a40> at usbus2, cfg=0 md=HOST spd=HIGH
> (480Mbps) pwr=SAVE (100mA)
>
> ugen2.3: <USB Optical Mouse Logitech> at usbus2, cfg=0 md=HOST spd=LOW
> (1.5Mbps) pwr=ON (100mA)
>
> ugen2.4: <USB Keyboard Logitech> at usbus2, cfg=0 md=HOST spd=LOW
> (1.5Mbps) pwr=ON (90mA)
>
> ugen2.5: <Back-UPS ES 700Y-IN FW895.m1.I USB FWm1 American Power
> Conversion> at usbus2, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (2mA)
>
> ugen2.5: <Back-UPS ES 700Y-IN FW895.m1.I USB FWm1 American Power
> Conversion> at usbus2, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (2mA)
>
>
> 4)
> usbconfig -u 2 -a 5 dump_device_desc
>
> bLength = 0x0012
> bDescriptorType = 0x0001
> bcdUSB = 0x0110
> bDeviceClass = 0x0000
> bDeviceSubClass = 0x0000
> bDeviceProtocol = 0x0000
> bMaxPacketSize0 = 0x0008
> idVendor = 0x051d
> idProduct = 0x0002
> bcdDevice = 0x0006
> iManufacturer = 0x0003 <American Power Conversion>
> iProduct = 0x0001 <Back-UPS ES 700Y-IN FW:895.m1.I USB FW:m1>
> iSerialNumber = 0x0002 <E21251005365 >
> bNumConfigurations = 0x0001
>
>
>
> 5)
> This is what I get in apctest.output when I run apctest :
>
> #{//start output
> 2015-03-06 11:43:17 apctest 3.14.12 (29 March 2014) freebsd
> Checking configuration ...
> sharenet.type = Network & ShareUPS Disabled
> cable.type = USB Cable
> mode.type = USB UPS Driver
> Setting up the port ...
> Doing prep_device() ...
>
> You are using a USB cable type, so I'm entering USB test mode
> Hello, this is the apcupsd Cable Test program.
> This part of apctest is for testing USB UPSes.
>
> Getting UPS capabilities...SUCCESS
>
> Please select the function you want to perform.
>
> 1) Test kill UPS power
> 2) Perform self-test
> 3) Read last self-test result
> 4) View/Change battery date
> 5) View manufacturing date
> 6) View/Change alarm behavior
> 7) View/Change sensitivity
> 8) View/Change low transfer voltage
> 9) View/Change high transfer voltage
> 10) Perform battery calibration
> 11) Test alarm
> 12) View/Change self-test interval
> Q) Quit
>
> Select function number: 2
>
>
> This test instructs the UPS to perform a self-test
> operation and reports the result when the test completes.
>
> Clearing previous self test result...CLEARED
> Initiating self test...INITIATED
> Waiting for test to complete...COMPLETED
> Result of last self test: PASSED
>
> 1) Test kill UPS power
> 2) Perform self-test
> 3) Read last self-test result
> 4) View/Change battery date
> 5) View manufacturing date
> 6) View/Change alarm behavior
> 7) View/Change sensitivity
> 8) View/Change low transfer voltage
> 9) View/Change high transfer voltage
> 10) Perform battery calibration
> 11) Test alarm
> 12) View/Change self-test interval
> Q) Quit
>
> Select function number: 4
>
> Current battery date: 05/28/2014
> Enter new battery date (MM/DD/YYYY), blank to quit:
>
> Invalid format.
>
> 1) Test kill UPS power
> 2) Perform self-test
> 3) Read last self-test result
> 4) View/Change battery date
> 5) View manufacturing date
> 6) View/Change alarm behavior
> 7) View/Change sensitivity
> 8) View/Change low transfer voltage
> 9) View/Change high transfer voltage
> 10) Perform battery calibration
> 11) Test alarm
> 12) View/Change self-test interval
> Q) Quit
>
> Select function number: 7
>
> Current sensitivity setting: MEDIUM
> Press...
> L for Low sensitivity
> M for Medium sensitivity
> H for High sensitivity
> Q to Quit with no changes
> Your choice: Select function: M
>
> New sensitivity setting: MEDIUM
>
> 1) Test kill UPS power
> 2) Perform self-test
> 3) Read last self-test result
> 4) View/Change battery date
> 5) View manufacturing date
> 6) View/Change alarm behavior
> 7) View/Change sensitivity
> 8) View/Change low transfer voltage
> 9) View/Change high transfer voltage
> 10) Perform battery calibration
> 11) Test alarm
> 12) View/Change self-test interval
> Q) Quit
>
> Select function number: 10
>
> This test instructs the UPS to perform a battery calibration
> operation and reports the result when the process completes.
> The battery level must be at 100% and the load must be at least
> 10% to begin this test.
>
> Failed to read current battery level
> #}//end output
>
>
> 6)
> Running /usr/local/etc/apcupsd/commfailure fails :
>
> /usr/local/etc/apcupsd # ./commfailure
> ./commfailure: -s: not found
> Error contacting apcupsd @ localhost:3551: Connection refused
>
>
>
> Regards
> Manish Jain
>
> #here is the complete dmesg :
>
> Copyright (c) 1992-2014 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 10.1-RELEASE #0 r274401: Tue Nov 11 22:51:51 UTC 2014
> root@releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC i386
> FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
> CPU: AMD Athlon(tm) II X2 270 Processor (3415.41-MHz 686-class CPU)
> Origin = "AuthenticAMD" Id = 0x100f63 Family = 0x10 Model = 0x6
> Stepping = 3
>
>
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
>
> Features2=0x802009<SSE3,MON,CX16,POPCNT>
> AMD
>
Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
> AMD
>
Features2=0x837ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,NodeId>
>
> TSC: P-state invariant
> real memory = 2147483648 (2048 MB)
> avail memory = 1819914240 (1735 MB)
> Event timer "LAPIC" quality 400
> ACPI APIC Table: <090412 APIC1527>
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> FreeBSD/SMP: 1 package(s) x 2 core(s)
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero
> address or length: 0x0000000000000000/0x1 (20130823/tbfadt-630)
> ioapic0 <Version 2.1> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> random: <Software, Yarrow> initialized
> acpi0: <090412 XSDT1527> on motherboard
> acpi0: Power Button (fixed)
> acpi0: reservation of fee00000, 1000 (3) failed
> acpi0: reservation of ffb80000, 80000 (3) failed
> acpi0: reservation of fec10000, 20 (3) failed
> acpi0: reservation of fed40000, 5000 (3) failed
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, 6fe00000 (3) failed
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> Event timer "RTC" frequency 32768 Hz quality 0
> hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 950
> Event timer "HPET" frequency 14318180 Hz quality 550
> Event timer "HPET1" frequency 14318180 Hz quality 450
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> vgapci0: <VGA-compatible display> port 0xd000-0xd0ff mem
> 0xd0000000-0xdfffffff,0xfebe0000-0xfebeffff,0xfea00000-0xfeafffff irq 18
> at device 5.0 on pci1
> vgapci0: Boot video device
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port
> 0xe800-0xe8ff mem 0xfdfff000-0xfdffffff,0xfdff8000-0xfdffbfff irq 16 at
> device 0.0 on pci2
> re0: Using 1 MSI-X message
> re0: Chip rev. 0x2c800000
> re0: MAC rev. 0x00100000
> miibus0: <MII bus> on re0
> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on
miibus0
> rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
> 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
> 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
> 1000baseT-FDX-flow-master, auto, auto-flow
> re0: Ethernet address: 50:46:5d:66:fd:10
> ahci0: <AMD SB7x0/SB8x0/SB9x0 AHCI SATA controller> port
> 0xc000-0xc007,0xb000-0xb003,0xa000-0xa007,0x9000-0x9003,0x8000-0x800f
> mem 0xfe9ffc00-0xfe9fffff irq 22 at device 17.0 on pci0
> ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ahcich1: <AHCI channel> at channel 1 on ahci0
> ahcich2: <AHCI channel> at channel 2 on ahci0
> ahcich3: <AHCI channel> at channel 3 on ahci0
> ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fe000-0xfe9fefff
> irq 16 at device 18.0 on pci0
> usbus0 on ohci0
> ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fd000-0xfe9fdfff
> irq 16 at device 18.1 on pci0
> usbus1 on ohci1
> ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem
> 0xfe9ff800-0xfe9ff8ff irq 17 at device 18.2 on pci0
> usbus2: EHCI version 1.0
> usbus2 on ehci0
> ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fc000-0xfe9fcfff
> irq 18 at device 19.0 on pci0
> usbus3 on ohci2
> ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fb000-0xfe9fbfff
> irq 18 at device 19.1 on pci0
> usbus4 on ohci3
> ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem
> 0xfe9ff400-0xfe9ff4ff irq 19 at device 19.2 on pci0
> usbus5: EHCI version 1.0
> usbus5 on ehci1
> atapci0: <ATI IXP700/800 UDMA133 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
> ata0: <ATA channel> at channel 0 on atapci0
> ata1: <ATA channel> at channel 1 on atapci0
> hdac0: <ATI SB600 HDA Controller> mem 0xfe9f4000-0xfe9f7fff irq 16 at
> device 20.2 on pci0
> isab0: <PCI-ISA bridge> at device 20.3 on pci0
> isa0: <ISA bus> on isab0
> pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
> pci3: <ACPI PCI bus> on pcib3
> ohci4: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fa000-0xfe9fafff
> irq 18 at device 20.5 on pci0
> usbus6 on ohci4
> acpi_button0: <Power Button> on acpi0
> ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> pmtimer0 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> hwpstate0: <Cool`n'Quiet 2.0> on cpu0
> Timecounters tick every 1.000 msec
> hdacc0: <Realtek ALC887 HDA CODEC> at cad 0 on hdac0
> hdaa0: <Realtek ALC887 Audio Function Group> at nid 1 on hdacc0
> pcm0: <Realtek ALC887 (Rear Analog)> at nid 20 and 24,26 on hdaa0
> pcm1: <Realtek ALC887 (Front Analog)> at nid 27 and 25 on hdaa0
> pcm2: <Realtek ALC887 (Onboard Digital)> at nid 17 on hdaa0
> random: unblocking device.
> usbus0: 12Mbps Full Speed USB v1.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 480Mbps High Speed USB v2.0
> usbus3: 12Mbps Full Speed USB v1.0
> usbus4: 12Mbps Full Speed USB v1.0
> usbus5: 480Mbps High Speed USB v2.0
> usbus6: 12Mbps Full Speed USB v1.0
> ugen5.1: <ATI> at usbus5
> uhub0: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
> ugen4.1: <ATI> at usbus4
> uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
> ugen3.1: <ATI> at usbus3
> uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
> ugen2.1: <ATI> at usbus2
> uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> ugen1.1: <ATI> at usbus1
> uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen0.1: <ATI> at usbus0
> uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ugen6.1: <ATI> at usbus6
> uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
> uhub6: 2 ports with 2 removable, self powered
> uhub1: 3 ports with 3 removable, self powered
> uhub2: 3 ports with 3 removable, self powered
> uhub4: 3 ports with 3 removable, self powered
> uhub5: 3 ports with 3 removable, self powered
> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> ada0: <WDC WD3200AAJS-00L7A0 01.03E01> ATA-8 SATA 1.x device
> ada0: Serial Number WD-WMAV27542837
> ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 305244MB (625140335 512 byte sectors: 16H 63S/T 16383C)
> ada0: Previously was known as ad4
> ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
> ada1: <WDC WD1600AAJS-00V4A0 05.01D05> ATA-8 SATA 2.x device
> ada1: Serial Number WD-WCAWF6026337
> ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada1: Command Queueing enabled
> ada1: 152626MB (312579695 512 byte sectors: 16H 63S/T 16383C)
> ada1: Previously was known as ad6
> cd0 at ahcich2 bus 0 scbus2 target 0 lun 0
> cd0: <HP DVD Writer 1260v AH24> Removable CD-ROM SCSI-0 device
> cd0: Serial Number 3524497 206238502323
> cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO
8192bytes)
> cd0: Attempt to query device size failed: NOT READY, Medium not present
> - tray closed
> SMP: AP CPU #1 Launched!
> Timecounter "TSC-low" frequency 1707704409 Hz quality 800
> uhub0: 6 ports with 6 removable, self powered
> uhub3: 6 ports with 6 removable, self powered
> Root mount waiting for: usbus2
> ugen2.2: <vendor 0x1a40> at usbus2
> uhub7: <vendor 0x1a40 USB 2.0 Hub, class 9/0, rev 2.00/1.11, addr 2> on
> usbus2
> Root mount waiting for: usbus2
> uhub7: 4 ports with 4 removable, self powered
> ugen2.3: <Logitech> at usbus2
> Root mount waiting for: usbus2
> ugen2.4: <Logitech> at usbus2
> ukbd0: <USB Keyboard> on usbus2
> kbd2 at ukbd0
> Root mount waiting for: usbus2
> ugen2.5: <American Power Conversion> at usbus2
> Trying to mount root from ufs:/dev/ada0s1a [rw]...
> ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3> on
> usbus2
> ums0: 3 buttons and [XYZ] coordinates ID=0
> uhid0: <USB Keyboard> on usbus2
> fuse-freebsd: version 0.4.4, FUSE ABI 7.8
> info: [drm] Initialized drm 1.1.0 20060810
> drmn0: <ATI Radeon 3000 Graphics> on vgapci0
> info: [drm] RADEON_IS_PCI
> info: [drm] initializing kernel modesetting (RS780 0x1002:0x9616
> 0x1043:0x8388).
> info: [drm] register mmio base: 0xFEBE0000
> info: [drm] register mmio size: 65536
> info: [drm] radeon_atrm_get_bios: ===> Try ATRM...
> info: [drm] radeon_atrm_get_bios: IGP card detected, skipping this
> method...
> info: [drm] radeon_acpi_vfct_bios: ===> Try VFCT...
> info: [drm] radeon_acpi_vfct_bios: Get "VFCT" ACPI table
> info: [drm] radeon_acpi_vfct_bios: Failed to get "VFCT" table:
AE_NOT_FOUND
> info: [drm] igp_read_bios_from_vram: ===> Try IGP's VRAM...
> info: [drm] igp_read_bios_from_vram: VRAM base address: 0xd0000000
> info: [drm] igp_read_bios_from_vram: Map address: 0xf021f000 (262144
bytes)
> info: [drm] igp_read_bios_from_vram: Incorrect BIOS signature: 0x5307
> info: [drm] radeon_read_bios: ===> Try PCI Expansion ROM...
> info: [drm] radeon_read_bios: Map address: 0xc00c0000 (131072 bytes)
> info: [drm] ATOM BIOS: B27722_RS780C
> drmn0: info: VRAM: 256M 0x00000000C0000000 - 0x00000000CFFFFFFF (256M
used)
> drmn0: info: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
> info: [drm] Detected VRAM RAM=256M, BAR=256M
> info: [drm] RAM width 32bits DDR
> [TTM] Zone kernel: Available graphics memory: 906222 kiB
> [TTM] Initializing pool allocator
> info: [drm] radeon: 256M of VRAM memory ready
> info: [drm] radeon: 512M of GTT memory ready.
> info: [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
> info: [drm] Driver supports precise vblank timestamp query.
> info: [drm] radeon: irq initialized.
> info: [drm] GART: num cpu pages 131072, num gpu pages 131072
> info: [drm] Loading RS780 Microcode
> info: [drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
> drmn0: info: WB enabled
> drmn0: info: fence driver on ring 0 use gpu addr 0x00000000a0000c00 and
> cpu addr 0x0xec6dcc00
> drmn0: info: fence driver on ring 3 use gpu addr 0x00000000a0000c0c and
> cpu addr 0x0xec6dcc0c
> info: [drm] ring test on 0 succeeded in 1 usecs
> info: [drm] ring test on 3 succeeded in 1 usecs
> info: [drm] ib test on ring 0 succeeded in 0 usecs
> info: [drm] ib test on ring 3 succeeded in 0 usecs
> info: [drm] radeon_device_init: Taking over the fictitious range
> 0xd0000000-0xe0000000
> iicbus0: <Philips I2C bus> on iicbb0 addr 0xf0
> iic0: <I2C generic I/O> on iicbus0
> iicbus1: <Philips I2C bus> on iicbb1 addr 0xc7
> iic1: <I2C generic I/O> on iicbus1
> iicbus2: <Philips I2C bus> on iicbb2 addr 0xc7
> iic2: <I2C generic I/O> on iicbus2
> iicbus3: <Philips I2C bus> on iicbb3 addr 0xc7
> iic3: <I2C generic I/O> on iicbus3
> iicbus4: <Philips I2C bus> on iicbb4 addr 0xc7
> iic4: <I2C generic I/O> on iicbus4
> info: [drm] Radeon Display Connectors
> info: [drm] Connector 0:
> info: [drm] VGA-1
> info: [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c
0x7e4c
> info: [drm] Encoders:
> info: [drm] CRT1: INTERNAL_KLDSCP_DAC1
> info: [drm] Connector 1:
> info: [drm] DVI-D-1
> info: [drm] HPD1
> info: [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c
0x7e5c
> info: [drm] Encoders:
> info: [drm] DFP3: INTERNAL_KLDSCP_LVTMA
> info: [drm] radeon: power management initialized
> info: [drm] fb mappable at 0xD0142000
> info: [drm] vram apper at 0xD0000000
> info: [drm] size 5787648
> info: [drm] fb depth is 24
> info: [drm] pitch is 6400
> fbd0 on drmn0
> info: [drm] Initialized radeon 2.29.0 20080528
Please let me know if you need any further information from me. If yes,
I would need specific commands to run on my system.
It is not as is I cannot live without the printer or the UPS. I just
feel that for so long - over 20 years - I have been of the opinion that
FreeBSD is the greatest idea anyone ever came across.
I wish I had more more to add to our community than just questions and
bug reports. But I cannot - I am very, very average.
Regards
Manish Jain
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BLU436-SMTP146AB4D040B70CC68410BA2F61A0>