Date: Wed, 27 Mar 2013 19:31:06 +0300 From: Odhiambo Washington <odhiambo@gmail.com> To: Leonardo Santagostini <lsantagostini@gmail.com> Cc: freebsd-questions@freebsd.org Subject: Re: Release 9.1 and 3G usb Modem Message-ID: <CAAdA2WNJ5GZtaJ4--62M3=CD4aaJkzZtFhJ2EQTQ=ovzOnyerg@mail.gmail.com> In-Reply-To: <CADmnP4Nh27_KQBiMi-n7e7EzWzRSnVrZpBuLmTuH=6qvqZon0A@mail.gmail.com> References: <CADmnP4Nh27_KQBiMi-n7e7EzWzRSnVrZpBuLmTuH=6qvqZon0A@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 27 March 2013 16:29, Leonardo Santagostini <lsantagostini@gmail.com>wrote:
> Hello all.
>
> I have a latitude e6400 with FreeBSD Release 9.1. And i can't get the USB
> modem working.
>
> I tried with umodem, u3g but no luck :(
>
[snip]
> ugen7.2: <HUAWEI> at usbus7
> ugen7.2: <HUAWEI> at usbus7 (disconnected)
> ugen7.2: <HUAWEI> at usbus7
> umodem0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
> umodem0: data interface 0, has no CM over data, has no break
> umodem1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
> umodem1: data interface 1, has no CM over data, has no break
> umodem2: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
> umodem2: data interface 2, has no CM over data, has no break
> umass0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
> umass0: SCSI over Bulk-Only; quirks = 0x0000
> umass0:9:0:-1: Attached to scbus9
> cd1 at umass-sim0 bus 0 scbus9 target 0 lun 0
> cd1: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
> cd1: 40.000MB/s transfers
> cd1: Attempt to query device size failed: NOT READY, Medium not present
> umass1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
> umass1: SCSI over Bulk-Only; quirks = 0x0000
> umass1:10:1:-1: Attached to scbus10
> da0 at umass-sim1 bus 1 scbus10 target 0 lun 0
> da0: <HUAWEI SD Storage 2.31> Removable Direct Access SCSI-2 device
> da0: 40.000MB/s transfers
> da0: Attempt to query device size failed: NOT READY, Medium not present
>
[snip]
Huawei modem, as I can see. That should be easy.
Connect to the modem through HyperTerminal or Putty on a different machine
Issue the command: AT^U2DIAG=0
That should disable the virtual CD-ROM and FreeBSD will see the modem.
Here are some commands you'll need to know about:
Do you have a Windows PC near you? If you plug the device into it and the
virtualCD pops up, then it means command was not successful. The fact that
fake CD still shows means command did not succeed!
AT^u2diag=0 (all off)
AT^u2diag=1 (CD on, SD off)
AT^u2diag=256 (CD off, SD is on)
AT^u2diag=255 (all on - including SD Card)
AT^u2diag=276 (Factory Reset)
A+CLAC - Display all available commands. However it does not tell you how
to use them
And here is a working ppp.conf - but you need to change the *bolded* values
to match your end of the environment:)
u3g:
set device */dev/cuaU0.0*
set server /var/run/3g-internet "" 0177
set speed 921600
set timeout 0
set authname *saf*
set authkey *data*
set dial "ABORT BUSY ABORT NO\\sTIMEOUT 2 \
\"\" \
AT OK-AT-OK \
AT+CFUN=1 OK-AT-OK \
AT+CMEE=2 OK-AT-OK \
AT+CSQ OK \
AT+CGDCONT=1,\\\"IP\\\",\\\"*APN*\\\" OK \
ATD**99#* CONNECT"
set crtscts on
disable vjcomp
disable acfcomp
disable deflate
disable deflate24
disable pred1
disable protocomp
disable mppe
disable ipv6cp
disable lqr
disable echo
#nat enable yes
enable dns
resolv writable
set dns 8.8.8.8
set ifaddr 10.1.0.2/0 10.1.0.1/0 255.255.255.255 0.0.0.0
add default HISADDR # See ppp.link*
Lemme know if you get stuck.
Also, always give details about modem - manufacturer, model...
--
Best regards,
Odhiambo WASHINGTON,
Nairobi,KE
+254733744121/+254722743223
"I can't hear you -- I'm using the scrambler."
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAAdA2WNJ5GZtaJ4--62M3=CD4aaJkzZtFhJ2EQTQ=ovzOnyerg>