Date: Thu, 29 Sep 2016 14:41:21 -0700 From: Adrian Chadd <adrian.chadd@gmail.com> To: Mori Hiroki <yamori813@yahoo.co.jp> Cc: "freebsd-mips@freebsd.org" <freebsd-mips@freebsd.org> Subject: Re: Solve: AR7161 USB Message-ID: <CAJ-Vmo=QgER78Wpn6Q4rPa=v8pEF7U-pBWNaZcLm3bdP3vTCrA@mail.gmail.com> In-Reply-To: <181104.30133.qm@web101710.mail.ssk.yahoo.co.jp> References: <379174.95890.qm@web101716.mail.ssk.yahoo.co.jp> <063ff05f-d464-823a-495c-abb800dfdaf5@freebsd.org> <105245.8987.qm@web101701.mail.ssk.yahoo.co.jp> <CAJ-VmokSNP%2BZr5s14TzvkNMukLHRFEK9p2jEpfjB=X5N4u1=Sw@mail.gmail.com> <181104.30133.qm@web101710.mail.ssk.yahoo.co.jp>
next in thread | previous in thread | raw e-mail | index | archive | help
Cool. There's some stuff you can put in hints to set on/off gpio functions. Can you provide a diff to the right .hints file so it's done at boot time? -adrian On 28 September 2016 at 23:46, Mori Hiroki <yamori813@yahoo.co.jp> wrote: > Hi > > Thanks for your advice. I can use USB on AR7161. > > # gpioctl 2 1 > # usbconfig > > ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr= > SAVE (0mA) > ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr > =SAVE (0mA) > ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST spd=FULL ( > 12Mbps) pwr=ON (100mA) > > Thanks. > > Hiroki Mori > > ----- Original Message ----- >> From: Adrian Chadd <adrian.chadd@gmail.com> >> To: Mori Hiroki <yamori813@yahoo.co.jp> >> Cc: "freebsd-mips@freebsd.org" <freebsd-mips@freebsd.org> >> Date: 2016/9/29, Thu 13:21 >> Subject: Re: AR7161 USB >> >> it could be something to do with port or phy power. check the default >> gpio settings for your board; some don't enable usb phy power. >> >> >> -a >> >> >> On 28 September 2016 at 20:51, Mori Hiroki <yamori813@yahoo.co.jp> wrote: >>> Hi. >>> >>> on WZR-HP-G300NH(AR9132) OK >>> >>> >>> >>> # usbconfig >>> ugen0.1: <EHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=HIGH >> (480Mbps) pwr >>> =SAVE (0mA) >>> ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST >> spd=FULL ( >>> 12Mbps) pwr=ON (100mA) >>> # >>> >>> >>> on WZR-HP-AG300H(AR7161) NG >>> >>> # usbconfig >>> ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL >> (12Mbps) pwr= >>> SAVE (0mA) >>> ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH >> (480Mbps) pwr >>> =SAVE (0mA) >>> >>> I use ZRouter on build. I check hints file. I seem same as >>> sys/mips/conf/AP96.hints. >>> >>> Thanks >>> >>> Hiroki Mori >>> >>> >>> >>> ----- Original Message ----- >>>> From: Sean Bruno <sbruno@freebsd.org> >>>> To: freebsd-mips@freebsd.org >>>> Cc: >>>> Date: 2016/9/27, Tue 23:10 >>>> Subject: Re: AR7161 USB >>>> >>>> >>>> >>>> On 09/27/16 04:02, Mori Hiroki wrote: >>>>> Hi. >>>>> >>>>> I try to use AR7161 target(WZR-HP-AG300H) on head today. >>>>> But I can't use USB this target. Device is probe on boot but >> USB device >>>>> insert not detect device. >>>>> >>>>> Any one use this ? >>>>> >>>>> Regards. >>>>> >>>>> Hiroki Mori >>>> >>>> Is umass.ko loaded? (I assume you are using a USB storage device). >>>> >>>> sean >>>> >>> _______________________________________________ >>> freebsd-mips@freebsd.org mailing list >>> https://lists.freebsd.org/mailman/listinfo/freebsd-mips >>> To unsubscribe, send any mail to >> "freebsd-mips-unsubscribe@freebsd.org" >> > _______________________________________________ > freebsd-mips@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-mips > To unsubscribe, send any mail to "freebsd-mips-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-Vmo=QgER78Wpn6Q4rPa=v8pEF7U-pBWNaZcLm3bdP3vTCrA>