Date: Wed, 21 Jan 2015 11:16:28 -0800 From: Adrian Chadd <adrian@freebsd.org> To: Reza Nikoopour <rnikoopour@gmail.com> Cc: "freebsd-embedded@freebsd.org" <freebsd-embedded@freebsd.org> Subject: Re: RBPi Doesn't Boot With GPS GPIO Board Attached Message-ID: <CAJ-VmomFNfEt9f-=v7mm2Gz=hw1BQUVBk2ppjRnWhwuXVXTzxQ@mail.gmail.com> In-Reply-To: <CAKesZq3ZB8j-MmNbCUoB2irdVyztuEPaVy-X95WqB9WQd3uZTg@mail.gmail.com> References: <CAKesZq3ZB8j-MmNbCUoB2irdVyztuEPaVy-X95WqB9WQd3uZTg@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, Does the GPS add-on speak to the raspberry PI serial console? If so, it's likely outputting a whole lot of GPS data via serial, and the boot loaders for both operating systems are interpreting that as valid input. -a On 21 January 2015 at 09:57, Reza Nikoopour <rnikoopour@gmail.com> wrote: > Hello, > > I'm currently building an NTP server using the following set up: > > Raspberry Pi B+ < > http://www.amazon.com/gp/product/B00LPESRUK/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 >> > Raspberry PI GPS Add-on < > http://imall.iteadstudio.com/raspberry-pi-gps-add-on.html > > FreeBSD 10.1 built with CrochetBSD > > I was able to build an img with Crochet and get the Pi to boot into a > shell. However, whenever I booting the Pi with the GPS board attached it > will not boot. > > When I plug in the GPS Add-on into the GPIO connector, my Pi fails to boot > before starting the kernel. It boots to the point where it says "Press > enter to prevent auto boot" and then the letter 'L' shows up and starts > erasing text from the screen. > > I was initially using a 1.5A power supply. It was suggested to me to try > using a stronger power supply so I tried a 2.1A power supply, but that > didn't work either. Using the 2.1A power supply resulted in the same boot > problem described above. > > Next I tried using Raspbian to boot the Pi, but a similar problem > occurred. The Pi boots without the GPS board attached. When the GPS board > is attached, it boots kernel and when the screen to start Raspbian Software > Configuration then the following message prints to the screen indefinitely: > > SysRq : HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) > memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystem(j) sak(k) > show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) > show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) > show-blocked-test(w) > > Could I get some guidance with fixing this problem? > > Thanks! > Reza > _______________________________________________ > freebsd-embedded@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-embedded > To unsubscribe, send any mail to "freebsd-embedded-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-VmomFNfEt9f-=v7mm2Gz=hw1BQUVBk2ppjRnWhwuXVXTzxQ>