Date: Mon, 9 Nov 2015 07:55:03 -0800 From: Adrian Chadd <adrian.chadd@gmail.com> To: Vladimir Botka <vbotka@gmail.com> Cc: freebsd-arm <freebsd-arm@freebsd.org> Subject: Re: wifi interface missing in 11.0 r290273 Hummingboard Message-ID: <CAJ-VmomGw7H38s6iErJAUt_nPxqjui5s3Xp_tW6ny_VMgmbrjA@mail.gmail.com> In-Reply-To: <20151109135438.7f429f41@planb> References: <20151109135438.7f429f41@planb>
next in thread | previous in thread | raw e-mail | index | archive | help
it's there: sysctl net.wlan.devices .. the top-level device was removed in freebsd-11.0. you can still clone it -eg "ifconfig wlan0 create wlandev run0" -a On 9 November 2015 at 04:54, Vladimir Botka <vbotka@gmail.com> wrote: > Hello, > > would it be possible to help me figure out why I'm missing the "run" > interface in 11.0-CURRENT arm r290273 [1] with RT5592 adapter? > > I can see the interface run0 in 10.2 i386 [4-6], but run0 in missing in > 11.0 arm [1-3]. The same behavior can be observed with RT5390. > > Cheers, > Vladimir > > [1] > # uname -a > FreeBSD imx6 11.0-CURRENT FreeBSD 11.0-CURRENT #0 r290273: Tue Nov 3 > 02:54:03 UTC 2015 > root@releng2.nyi.freebsd.org:/usr/obj/arm.armv6/usr/src/sys/IMX6 arm > > [2] > Nov 9 12:41:12 imx6 kernel: ugen1.3: <Ralink> at usbus1 (disconnected) > Nov 9 12:41:13 imx6 kernel: run0: at uhub2, port 1, addr 3 > (disconnected) > Nov 9 12:41:20 imx6 kernel: ugen1.3: <Ralink> at usbus1 > Nov 9 12:41:21 imx6 kernel: run0: <1.0> on usbus1 > Nov 9 12:41:21 imx6 kernel: run0: MAC/BBP RT5592 (rev 0x0222), RF > RT5592 (MIMO 2T2R), address 64:70:02:27:d6:42 > > [3] > # ifconfig -a > ffec0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu > 1500 options=80008<VLAN_MTU,LINKSTATE> > ether d0:63:00:00:00:00 > inet 192.168.1.40 netmask 0xffffff00 broadcast 192.168.1.255 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 > inet 127.0.0.1 netmask 0xff000000 > groups: lo > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > > [4] > # uname -a > FreeBSD vlado-srv 10.2-RELEASE FreeBSD 10.2-RELEASE #0 r286666: Wed Aug > 12 19:31:38 UTC 2015 > root@releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC i386 > > [5] > Nov 9 13:39:48 vlado-srv kernel: ugen1.3: <Ralink> at usbus1 > Nov 9 13:39:48 vlado-srv kernel: run0: <1.0> on usbus1 > Nov 9 13:39:48 vlado-srv kernel: run0: MAC/BBP RT5592 (rev 0x0222), RF > RT5592 (MIMO 2T2R), address 64:70:02:27:d6:42 > Nov 9 13:39:48 vlado-srv devd: Executing '/etc/pccard_ether run0 > start' > Nov 9 13:39:48 vlado-srv devd: Executing '/etc/pccard_ether run0 > start' > Nov 9 13:39:56 vlado-srv kernel: run0: firmware RT3071 ver. 0.33 loaded > > [6] > # ifconfig run0 > run0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 > ether 64:70:02:27:d6:42 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) > status: no carrier > --
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-VmomGw7H38s6iErJAUt_nPxqjui5s3Xp_tW6ny_VMgmbrjA>