Date: Mon, 13 Sep 1999 10:16:30 -0300 (EST) From: Luiz Morte da Costa Junior <morte@correionet.com.br> To: freebsd-hackers@freebsd.org Cc: Luiz Morte da Costa Junior <morte@correionet.com.br> Subject: L440GX+ Server Board Message-ID: <Pine.BSF.4.10.9909131001030.69311-100000@caxton.correionet.com.br>
next in thread | raw e-mail | index | archive | help
Hi list, I can't solve the problem yet. When I runnig the dmesg command, I have: --- da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST39140LW 1483> Fixed Direct Access SCSI-2 device da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C) da1 at ahc0 bus 0 target 1 lun 0 da1: <SEAGATE ST39140LW 1483> Fixed Direct Access SCSI-2 device da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da1: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C) --- I did a test, changing only the SCSI disk, using the same motherboard (L440GX+). I ran the dmesg command again and I received: -- da0 at ahc0 bus 0 target 0 lun 0 da0: <QUANTUM QM39100TD-SW N491> Fixed Direct Access SCSI-2 device da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da0: 8683MB (17783250 512 byte sectors: 255H 63S/T 1106C) -- I realized that the quantum disk have a 80.000MB/s transfers. Does someone use a SEAGATE ST39140LW disk and have I/O problems? Regards, Luiz Morte. PS: Someone told me that vipw doens't have much I/O disk, but when I run it with 12000 accounts, my disk have a lot off access. On Sun, 22 Aug 1999, Luiz Morte da Costa Junior wrote: > > Hi all, > > I have a problem with a server running a FreeBSD 3.2. > > My Server has a L440GX+ Serber Board (intel), with network card 10/100, > SCSI AIC 7896 (80MB/s), 2 SCSI disk with 9GB (80MB/s), 2 pentium III > 450Mhz (not overclocked). The NIC and SCSI are onboard. > > I recompiled a kernel to SMP, and it worked. The server is ok, but when I > run a comand with disk access (whith vipw or mysql), the performance of > server goes down. My server stays very very very slow. If I use pine to > read my messages, it doesn't work. When the comand finishes, the server > stays "ok" again. > > I recompiled the kernel with "maxusers 128", but it doesn't work. > > My SCSI cable has a terminator and the scsi setup is ok (I think :) ). > > The dmesg command output is in attchmnt. > > I appreciate any help. []s, Luiz Morte da Costa Junior Analista de Redes E-mail: morte@correionet.com.br Telefone: +55 19 754-2532 Fax: +55 19 255-7576 CorreioNet - Correio Popular Campinas - SP - Brazil To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.9909131001030.69311-100000>