Date: Wed, 5 Feb 2003 12:32:30 -0500 (EST) From: Adam Mazza <adam@68e.com> To: Andrew Chadwick <andrewc@piffle.org> Cc: questions@FreeBSD.org Subject: Re: sparc64/sbus: "No disks found" during install/partitioning on Sun Ultra Enterprise 1 Message-ID: <Pine.NEB.4.51.0302051231290.29332@panix1.panix.com> In-Reply-To: <20030205171635.GA7272@piffle.org> References: <20030205171635.GA7272@piffle.org>
next in thread | previous in thread | raw e-mail | index | archive | help
http://www.freebsd.org/releases/5.0R/hardware-sparc64.html#AEN61 fas device isn't supported. You can try and run the U1 as a diskless client. There's a good article on that at www.daemonnews.org Adam On Wed, 5 Feb 2003, Andrew Chadwick wrote: > Hi there, > > I get a "No disks found" during the disk partitioning phase of a FreeBSD > Standard install using the image at <ftp://ftp.freebsd.org/pub/FreeBSD/ > releases/sparc64/ISO-IMAGES/5.0/5.0-RELEASE-sparc64-miniinst.iso> on the > office's spare Ultra Enterprise 1. The docs I read at <http://people.freebsd > .org/~bmah/relnotes/5.0-RELEASE/installation-sparc64.html> weren't too > useful. This machine contains one old installation of Solaris, FYI, but > we don't need to keep that. > > This would be my first introduction to FreeBSD, so be gentle. > > > Message > > |No disks found! Please verify that your disk controller is being > |properly probed at boot time. See the Hardware Guide on the > |Documentation menu for clues on diagnosing this type of problem. > > [ OK ] > Press enter or space > > HARDWARE.TXT wasn't useful. Invoking Disklabel from the Index (Glossary > of functions) menu preoduces the same message. > > Here's the output of devalias in Open Firmware > > ------------------------------------- > screen /sbus@1f,0/cgsix@2,0 > net-aui /sbus/ledma@e,8400010:aui/le@e,8c00000 > net-tpe /sbus/ledma@e,8400010:tpe/le@e,8c00000 > net /sbus/ledma@e,8400010/le@e,8c00000 > disk /sbus/espdma@e,8400000/esp@e,8800000/sd@0,0 > cdrom /sbus/espdma@e,8400000/esp@e,8800000/sd@6,0:f > tape /sbus/espdma@e,8400000/esp@e,8800000/st@4,0 > tape1 /sbus/espdma@e,8400000/esp@e,8800000/st@5,0 > tape0 /sbus/espdma@e,8400000/esp@e,8800000/st@4,0 > disk6 /sbus/espdma@e,8400000/esp@e,8800000/sd@6,0 > disk5 /sbus/espdma@e,8400000/esp@e,8800000/sd@5,0 > disk4 /sbus/espdma@e,8400000/esp@e,8800000/sd@4,0 > disk3 /sbus/espdma@e,8400000/esp@e,8800000/sd@3,0 > disk2 /sbus/espdma@e,8400000/esp@e,8800000/sd@2,0 > disk1 /sbus/espdma@e,8400000/esp@e,8800000/sd@1,0 > disk0 /sbus/espdma@e,8400000/esp@e,8800000/sd@0,0 > scsi /sbus/espdma@e,8400000/esp@e,8800000 > floppy /sbus/SUNW,fdtwo > ttyb /sbus/zs@f,1100000:b > ttya /sbus/zs@f,1100000:a > keyboard! /sbus/zs@f,1000000:forcemode > keyboard /sbus/zs@f,1000000 > name aliases > ---------------- > > The output from probe-scsi-all: > > --------------------------- > /sbus@1f,0/espdma@e,8400000/esp@e,8800000 > Target 0 > Unit 0 Disk IBM DCAS32160SUN2.1GS65A > Target 1 > Unit 0 Disk IBM DCAS32160SUN2.1GS65A > Target 6 > Unit 0 Removable Read Only device NEC CD-ROM DRIVE:5022.0y > ---------------------------- > > And the output from the install CD's boot sequence: > > ------------------------------------------------------------------------ > Boot device: /sbus/espdma@e,8400000/esp@e,8800000/sd@6,0:f File and > args: > > >> FreeBSD/sparc64 boot block > Boot path: /sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:f > Boot loader: /boot/loader > Console: OpenFirmware console > Boot path set to /sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:a > > FreeBSD/sparc64 bootstrap loader, Revision 1.0 > (scottl@numenor.btc.adaptec.com, Thu Jan 16 07:21:26 MST 2003) > bootpath="/sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:a" > Loading /boot/defaults/loader.conf > /boot/kernel/kernel data=0x312c08+0xe77b8 syms=[0x8+0x49890+0x8+0x38cf5] > | > Hit [Enter] to boot immediately, or any other key for command prompt. > Booting [/boot/kernel/kernel]... > nothing to autoload yet. > jumping to kernel entry at 0xc0038000. > stray vector interrupt 2033 > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.0-RELEASE #0: Fri Jan 17 20:03:38 GMT 2003 > root@numenor.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc0880000. > Preloaded mfs_root "/boot/mfsroot" at 0xc0880190. > Timecounter "tick" frequency 166982390 Hz > cpu0: Sun Microsystems UltraSparc-I Processor (166.98 MHz CPU) > Model: SUNW,Ultra-1 > Initializing GEOMetry subsystem > md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc047c958 > nexus0: <OpenFirmware Nexus device> > sbus0: clock 25.000 MHz > DVMA map: 0xff800000 to 0xffffffff > initialializing counter-timer > Timecounter "counter-timer" frequency 1000000 Hz > sbus0: <U2S UPA-SBus bridge> on nexus0 > sbus0: <SUNW,CS4231>, type (unknown) (no driver attached) > sbus0: <auxio>, type (unknown) (no driver attached) > sbus0: <flashprom>, type (unknown) (no driver attached) > sbus0: <SUNW,fdtwo>, type block (no driver attached) > eeprom0: <SBus EEPROM/clock> mem 0x1200000-0x1201fff on sbus0 > eeprom0: model mk48t59 > eeprom0: hostid 808898c3 > sbus0: <zs>, type serial (no driver attached) > sbus0: <zs>, type serial (no driver attached) > sbus0: <sc>, type (unknown) (no driver attached) > sbus0: <SUNW,pll>, type (unknown) (no driver attached) > sbus0: <espdma>, type (unknown) (no driver attached) > sbus0: <ledma>, type (unknown) (no driver attached) > sbus0: <SUNW,bpp>, type (unknown) (no driver attached) > hme0: <Sun HME 10/100 Ethernet> mem > 0x8c07000-0x8c0701f,0x8c06000-0x8c07fff,0x8c04000-0x8c05fff,0x8c02000-0x8c03fff,0x8c00000-0x8c0 > 0107 irq 1988 on sbus0 > hme0: Ethernet address: 08:00:20:88:98:c3 > miibus0: <MII bus> on hme0 > nsphy0: <DP83840 10/100 media interface> on miibus0 > nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sbus0: <cgsix>, type display (no driver attached) > Timecounters tick every 10.000 msec > Mounting root from ufs:/dev/md0 > Invalid time in real time clock. > Check and reset the date immediately! > /stand/sysinstall running as init on serial console > > These are the predefined terminal types available to > sysinstall when running stand-alone. Please choose the > closest match for your particular terminal. > > 1 ...................... Standard ANSI terminal. > 2 ...................... VT100 or compatible terminal. > 3 ...................... FreeBSD system console (color). > 4 ...................... FreeBSD system console (monochrome). > > 5 ...................... xterm terminal emulator. > > Your choice: (1-5) 2 > ------------------------------------ > > Am I missing anything here? > > > -- > Andrew Chadwick > <Secure beneath the watchful eyes> > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.NEB.4.51.0302051231290.29332>