Date: Fri, 29 Mar 2002 17:27:40 -0500 (EST) From: "Adam D. Gorski" <agorski@engin.umich.edu> To: <bdodson@scms.utmb.edu> Cc: <freebsd-multimedia@freebsd.org> Subject: Re: SB problem (was: Cat'ing /dev/audio) Message-ID: <Pine.SOL.4.33.0203291722530.9718-100000@and.engin.umich.edu> In-Reply-To: <200203292143.g2TLhLA97186@scms.utmb.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
Ok.. I compared dmesg versus pciconf -l, and I found this.. I dunno if this means anything, but I figured I'd mention it... the first matching works, which is for my 3Com card: * dmesg: xl0: <3Com 3c900B-TPO Etherlink XL> port 0xd000-0xd07f mem 0xe1000000-0xe100007f irq 9 at device 9.0 on pci0 * pciconf -l xl0@pci0:9:0: class=0x020000 card=0x900410b7 chip=0x900410b7 rev=0x04 hdr=0x00 So both show IRQ 9 (if I'm reading the output right) which seems fine.. but.. check out my RTL and SB outputs: * dmesg rl0: <RealTek 8139 10/100BaseTX> port 0x9800-0x98ff mem 0xe0000000-0xe00000ff irq 11 at device 12.0 on pci0 pcm0: <Creative CT5880-C> port 0xa000-0xa03f irq 10 at device 11.0 on pci0 * pciconf -l rl0@pci0:12:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 hdr=0x00 pcm0@pci0:11:0: class=0x040100 card=0x20001274 chip=0x58801274 rev=0x02 hdr=0x00 Ok, notice how one lists the SB @ IRQ 10, while the other shows it @ IRQ 11? I dunno, just something that caught my eye based on the suggestions below. Maybe this helps, - Adam On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: ::On 29 Mar, Adam D. Gorski wrote: ::> Hey, ::> ::> Thanks for the response. I went into my BIOS and told it that I don't have a ::> PnP OS, but the modules still did not detect the card. So I re-compiled the ::> kernel with 'device pcm', and the card is detected once again, but the ::> problems persist. I'm going to try some things that were suggested still, ::> and hopefully I'll get at least a step closer to the solution. Thanks once ::> again! ::> ::> - Adam ::> :: ::Hmm... I'm out of ideas. The bare 'device pcm' is right for devices ::being configured by pnp (as all pci devices are). 'device pcm0 ......' ::is right for devices which need to be hand configured (only isa or ::pccard devices). It sounds to me like you may have pci irq (or other ::resource) conflicts. You might try to do :: ::pciconf -vl (as root) :: ::and see if anything shows up that looks obviously bogus. I'm sorry I ::can't help you with the interpretation, but if you post the result to ::the multimedia list, this may allow them to give you better help. :: ::Good luck, ::Bud :: ::> On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: ::> ::> ::(reading your post via the archives, not subscribed to multimedia) ::> :: ::> ::I'm sure that someone will point out that FreeBSD is NOT a "PnP OS", so ::> ::you need to set your BIOS to "PnP OS = NO". I have no idea whether that ::> ::will fix your problem, but I know for sure setting it to YES is wrong. ::> ::That is probably why the modules did not work right: nothing is ::> ::configuring PNP. ::> :: ::> ::Good luck, ::> ::Bud Dodson ::> :: :: :: ::-- ::M. L. Dodson bdodson@scms.utmb.edu ::409-772-2178 FAX: 409-772-1790 :: :: To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-multimedia" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.SOL.4.33.0203291722530.9718-100000>