Date: Wed, 23 Jun 2021 12:53:12 +0200 From: Dmitry Salychev via freebsd-arm <freebsd-arm@freebsd.org> To: Mark Millard <marklmi@yahoo.com> Cc: freebsd-arm <freebsd-arm@freebsd.org> Subject: Re: HoneyComb first-boot notes Message-ID: <YNMSmCkrXpEOMtMI@x230.ds> In-Reply-To: <A8469092-0001-4442-B90C-F3960B85D829@yahoo.com> References: <8A6C415F-A57B-4F2F-861F-052B487166D6.ref@yahoo.com> <8A6C415F-A57B-4F2F-861F-052B487166D6@yahoo.com> <YNGT5hcHOBd6cU4T@x230.ds> <40AE6447-77AF-4D0E-864F-AD52D9F3346F@yahoo.com> <YNGf999RsaTfNhcp@x230.ds> <0DF376DC-C4A5-494C-BAA5-782516596CF0@yahoo.com> <YNGrdIhpdupSXm2a@x230.ds> <A8469092-0001-4442-B90C-F3960B85D829@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
> >>>>>> I put an existing FreeBSD Optane into a just delivered > >>>>>> HoneyComb, put in the RAM and the matching UEFI/ACPI > >>>>>> image on a microsd card and put the card in the slot. > >>>>>> I plugged in a USB3 Ethernet dongle, like I use on some > >>>>>> other systems. Serial console via its USB port for such. > >>>>>> (Optane instead of video card.) The UEFI/ACPI image was > >>>>>> extracted from: > >>>>>> > >>>>>> https://solid-run-images.sos-de-fra-1.exo.io/LX2k/lx2160a_uefi/lx2= 160acex7_2000_700_2900_8_5_2_sd_81b4bbe.img.xz > >>>>>> > >>>>>> in order to match the RAM and being based on the > >>>>>> most current vintage at: > >>>>>> > >>>>>> https://github.com/SolidRun/lx2160a_uefi/ > >>>>>> > >>>>>> It booted. > >>>>> > >>>>> Could you share whole dmesg? > >>>> > >>>> I've not done a "boot -v" . The below is actually from a > >>>> captured serial console output. It is lightly edited. I > >>>> have omitted nearly all loader output (and before). > >>>> > >>> > >>> Thanks for sharing. Have you seen somewhere in output from UEFI (befo= re > >>> the loader) that "DPAA2 Management Complex initialized"? > >> > >> The text "DPAA2" does not occur in the captured output > >> at all. However, that is my understanding of the expected > >> status. > > > > That's strange because DPAA2 firmware should be included into UEFI buil= t from > > lx2160a_uefi: > > > > https://github.com/SolidRun/edk2-platforms/blob/edk2-stable202102-lx216= 0acex7/Platform/SolidRun/LX2160aCex7/LX2160aCex7.fdf#L252 > > > > I assumed that there might be any output that firmware has been loaded = correctly > > at least. > > The edk2 build is not a debug build and, before putting up > the menu, only outputs (I stripped some escape sequences): > > > NOTICE: UDIMM KHX2933C17S4/32G > NOTICE: DDR4 UDIMM with 2-rank 64-bit bus (x8) > > NOTICE: 64 GB DDR4, 64-bit, CL=3D17, ECC off, 256B, CS0+CS1 > NOTICE: BL2: Booting BL31 > NOTICE: BL31: v2.4(release):v2.0-4462-ge7b392d0a > NOTICE: BL31: Built : 07:47:10, May 31 2021 > NOTICE: Welcome to lx2160acex7 BL31 Phase > > UEFI firmware built at 07:44:26 on May 31 2021. version: > 202102 > SOC: LX2160ACE Rev2.0 (0x87360020) > UEFI firmware (version 202102 built at 07:44:28 on May 31 2021) > Tianocore/EDK2 firmware version 202102 > Press ESCAPE for boot options .... > > After the menu things start with basically: > > Consoles: serial port > |=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-= =08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08= /=08-=08\=08|=08/=08-=08\=08 Reading loader env vars from /efi/freebsd/l= oader.env > Setting currdev to disk2p1: > |=08/=08-=08\=08|=08/=08FreeBSD/arm64 EFI loader, Revision 1.1 > > Command line arguments: loader.efi > Image base: 0xedc89000 > EFI version: 2.70 > EFI Firmware: EDK II (rev 0.00) > Console: comconsole (0) > Load Path: \EFI\BOOT\BOOTAA64.EFI > . . . > > One might be able to make inferences from the content > of some potential menu displays. Otherwise, I expect > that a debug build would be required to see DPAA2 > references. > > I do not expect one can validly infer much from the > lack of "DPAA2" text in my boot sequence (with any > capitalization vs. lower case status). > > =3D=3D=3D > Mark Millard > marklmi at yahoo.com > ( dsl-only.net went > away in early 2018-Mar) > Could you share an output of "acpidump -d"? Regards, Dmitry
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?YNMSmCkrXpEOMtMI>