Date: Mon, 23 Mar 2009 15:04:55 -0500 From: Neal Hogan <nealhogan@gmail.com> To: freebsd-questions@freebsd.org Subject: xorg-server-1.5.3_7, /usr/ports/UPDATING, mouse Message-ID: <ab7b49bc0903231304s7b99689et1f4c1fca4efc4bec@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Well, recently I deinstalled all of my third party apps . . . long story (some of which is documented on this list) . . . but the short story is that some were added via the ports tree and others via pkg_add. When it came time to portupdate, I was having problems and it was brought to my attention that, among other things, mixing ports and packages may lead to problems. Also, I didn't do the massive deinstall until after I had portupgraded all of my packages individually and the mouse/keyboard didn't work with X (it did at the console). Once this happened I felt compelled to wipe the slate. So, with no ports/packages installed and starting with a fresh ports tree, I began installing them one-by-one: 1) cd /usr/ports/path/port 2) make && make install && make clean I started with xorg. After it was installed, I tried to start X (startx) . . . no dice . . . no big deal. I created the basic xorg.conf (Xorg -configure), tried it (Xorg -config xorg.conf.new). X started, but no mouse activity and ctrl+alt+backspace did not quit X. I had moused enable in rc.conf and, as I say above the mouse worked (i.e., it moved when asked) at the console. /usr/ports/UPDATING says that some mouse issues were cleared up: "20090124: 241 AFFECTS: users of x11-servers/xorg-server, sysutils/hal 242 AUTHOR: rnoland@FreeBSD.org 243 244 sysutils/hal has been updated and should now properly detect 245 mice for use in Xorg. Use of AllowEmptyInput should no longer 246 be needed for most users and moused should now work fine." But, as I say, I have no mouse under X. So, I try adding: Option "AllowEmptyInput" "off" in my xorg.conf and "Hey! We gotta mouse!" I just rebooted and the mouse still works in X, but just before rebooting I disabled moused (in rc.conf -> moused_enable="NO"). So, adding the above line to xorg.conf helped with/without moused. Note that prior to this whole portupgrade deal I was running 7.1-RELEASE without an xorg.conf, put with an older xorg. At this point, I'm not upset b/c everything seems to be working fine. Just curious what might be going on. Thanks for you time. Below is my dmesg. 1 Copyright (c) 1992-2009 The FreeBSD Project. 2 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 3 The Regents of the University of California. All rights reserved. 4 FreeBSD is a registered trademark of The FreeBSD Foundation. 5 FreeBSD 7.1-RELEASE #0: Sat Jan 10 19:07:15 CST 2009 6 nph@frege.lambdaserver:/usr/obj/usr/src/sys/GENERIC 7 Timecounter "i8254" frequency 1193182 Hz quality 0 8 CPU: mobile AMD Athlon(tm) XP2400+ (1788.94-MHz 686-class CPU) 9 Origin = "AuthenticAMD" Id = 0x6a0 Stepping = 0 10 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMO V,PAT,PSE36,MMX,FXSR,SSE> 11 AMD Features=0xc0480800<SYSCALL,MP,MMX+,3DNow!+,3DNow!> 12 real memory = 468647936 (446 MB) 13 avail memory = 444530688 (423 MB) 14 kbd1 at kbdmux0 15 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) 16 acpi0: <PTLTD RSDT> on motherboard 17 acpi0: [ITHREAD] 18 acpi0: Power Button (fixed) 19 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 20 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 21 acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0 22 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 23 pci_link5: BIOS IRQ 10 for 0.10.INTA is invalid 24 pci0: <ACPI PCI bus> on pcib0 25 agp0: <ATI RS100 AGP bridge> on hostb0 26 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 27 pci1: <ACPI PCI bus> on pcib1 28 vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem 0xe0000000-0xefffff ff,0xd0100000-0xd010ffff irq 10 at device 5.0 on pci1 29 ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0xd0006000-0xd0006fff irq 9 at device 2.0 on pci0 30 ohci0: [GIANT-LOCKED] 31 ohci0: [ITHREAD] 32 usb0: OHCI version 1.0, legacy support 33 usb0: SMM does not respond, resetting 34 usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0 35 usb0: USB revision 1.0 36 uhub0: <AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 37 uhub0: 4 ports with 4 removable, self powered 38 pcm0: <Acer Labs M5451> port 0x8400-0x84ff mem 0xd0007000-0xd0007fff irq 5 a t device 6.0 on pci0 39 pcm0: <Conexant CX20468 AC97 Codec> 40 pcm0: [GIANT-LOCKED] 41 pcm0: [ITHREAD] 42 isab0: <PCI-ISA bridge> at device 7.0 on pci0 43 isa0: <ISA bus> on isab0 44 pci0: <simple comms, generic modem> at device 8.0 (no driver attached) 45 pci0: <network> at device 9.0 (no driver attached) 46 cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 10.0 on pci0 47 cardbus0: <CardBus bus> on cbb0 48 pccard0: <16-bit PCCard bus> on cbb0 49 cbb0: [ITHREAD] 50 fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem 0xd0009000-0xd00097ff,0 xd0000000-0xd0003fff irq 10 at device 12.0 on pci0 51 fwohci0: [FILTER] 52 fwohci0: OHCI version 1.10 (ROM=1) 53 fwohci0: No. of Isochronous channels is 4. 54 fwohci0: EUI64 00:0d:9d:71:9e:43:0c:6a 55 fwohci0: Phy 1394a available S400, 1 ports. 56 fwohci0: Link S400, max_rec 2048 bytes. 57 firewire0: <IEEE1394(FireWire) bus> on fwohci0 58 fwe0: <Ethernet over FireWire> on firewire0 59 if_fwe0: Fake Ethernet address: 02:0d:9d:43:0c:6a 60 fwe0: Ethernet address: 02:0d:9d:43:0c:6a 61 fwip0: <IP over FireWire> on firewire0 62 fwip0: Firewire address: 00:0d:9d:71:9e:43:0c:6a @ 0xfffe00000000, S400, max rec 2048 63 sbp0: <SBP-2/SCSI over FireWire> on firewire0 64 dcons_crom0: <dcons configuration ROM> on firewire0 65 dcons_crom0: bus_addr 0x12bc000 66 fwohci0: Initiate bus reset 67 fwohci0: BUS reset 68 fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode 69 atapci0: <AcerLabs M5229 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x 177,0x376,0x8080-0x808f at device 16.0 on pci0 37 uhub0: 4 ports with 4 removable, self powered 38 pcm0: <Acer Labs M5451> port 0x8400-0x84ff mem 0xd0007000-0xd0007fff irq 5 a t device 6.0 on pci0 39 pcm0: <Conexant CX20468 AC97 Codec> 40 pcm0: [GIANT-LOCKED] 41 pcm0: [ITHREAD] 42 isab0: <PCI-ISA bridge> at device 7.0 on pci0 43 isa0: <ISA bus> on isab0 44 pci0: <simple comms, generic modem> at device 8.0 (no driver attached) 45 pci0: <network> at device 9.0 (no driver attached) 46 cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 10.0 on pci0 47 cardbus0: <CardBus bus> on cbb0 48 pccard0: <16-bit PCCard bus> on cbb0 49 cbb0: [ITHREAD] 50 fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem 0xd0009000-0xd00097ff,0 xd0000000-0xd0003fff irq 10 at device 12.0 on pci0 51 fwohci0: [FILTER] 52 fwohci0: OHCI version 1.10 (ROM=1) 53 fwohci0: No. of Isochronous channels is 4. 54 fwohci0: EUI64 00:0d:9d:71:9e:43:0c:6a 55 fwohci0: Phy 1394a available S400, 1 ports. 56 fwohci0: Link S400, max_rec 2048 bytes. 57 firewire0: <IEEE1394(FireWire) bus> on fwohci0 58 fwe0: <Ethernet over FireWire> on firewire0 59 if_fwe0: Fake Ethernet address: 02:0d:9d:43:0c:6a 60 fwe0: Ethernet address: 02:0d:9d:43:0c:6a 61 fwip0: <IP over FireWire> on firewire0 62 fwip0: Firewire address: 00:0d:9d:71:9e:43:0c:6a @ 0xfffe00000000, S400, max rec 2048 63 sbp0: <SBP-2/SCSI over FireWire> on firewire0 64 dcons_crom0: <dcons configuration ROM> on firewire0 65 dcons_crom0: bus_addr 0x12bc000 66 fwohci0: Initiate bus reset 67 fwohci0: BUS reset 68 fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode 69 atapci0: <AcerLabs M5229 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x 177,0x376,0x8080-0x808f at device 16.0 on pci0 37 uhub0: 4 ports with 4 removable, self powered 38 pcm0: <Acer Labs M5451> port 0x8400-0x84ff mem 0xd0007000-0xd0007fff irq 5 a t device 6.0 on pci0 39 pcm0: <Conexant CX20468 AC97 Codec> 40 pcm0: [GIANT-LOCKED] 41 pcm0: [ITHREAD] 42 isab0: <PCI-ISA bridge> at device 7.0 on pci0 43 isa0: <ISA bus> on isab0 44 pci0: <simple comms, generic modem> at device 8.0 (no driver attached) 45 pci0: <network> at device 9.0 (no driver attached) 46 cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 10.0 on pci0 47 cardbus0: <CardBus bus> on cbb0 48 pccard0: <16-bit PCCard bus> on cbb0 49 cbb0: [ITHREAD] 50 fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem 0xd0009000-0xd00097ff,0 xd0000000-0xd0003fff irq 10 at device 12.0 on pci0 51 fwohci0: [FILTER] 52 fwohci0: OHCI version 1.10 (ROM=1) 53 fwohci0: No. of Isochronous channels is 4. 54 fwohci0: EUI64 00:0d:9d:71:9e:43:0c:6a 55 fwohci0: Phy 1394a available S400, 1 ports. 56 fwohci0: Link S400, max_rec 2048 bytes. 57 firewire0: <IEEE1394(FireWire) bus> on fwohci0 58 fwe0: <Ethernet over FireWire> on firewire0 59 if_fwe0: Fake Ethernet address: 02:0d:9d:43:0c:6a 60 fwe0: Ethernet address: 02:0d:9d:43:0c:6a 61 fwip0: <IP over FireWire> on firewire0 62 fwip0: Firewire address: 00:0d:9d:71:9e:43:0c:6a @ 0xfffe00000000, S400, max rec 2048 63 sbp0: <SBP-2/SCSI over FireWire> on firewire0 64 dcons_crom0: <dcons configuration ROM> on firewire0 65 dcons_crom0: bus_addr 0x12bc000 66 fwohci0: Initiate bus reset 67 fwohci0: BUS reset 68 fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode 69 atapci0: <AcerLabs M5229 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x 177,0x376,0x8080-0x808f at device 16.0 on pci0 70 atapci0: using PIO transfers above 137GB as workaround for 48bit DMA access bug, expect reduced performance 71 ata0: <ATA channel 0> on atapci0 72 ata0: [ITHREAD] 73 ata1: <ATA channel 1> on atapci0 74 ata1: [ITHREAD] 75 pci0: <bridge> at device 17.0 (no driver attached) 76 sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x8c00-0x8cff mem 0xd000a000-0x d000afff irq 11 at device 18.0 on pci0 77 sis0: Silicon Revision: DP83816A 78 miibus0: <MII bus> on sis0 79 nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0 80 nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto 81 sis0: Ethernet address: 00:0d:9d:43:2b:a7 82 sis0: [ITHREAD] 83 acpi_button0: <Power Button> on acpi0 84 acpi_lid0: <Control Method Lid Switch> on acpi0 85 acpi_acad0: <AC Adapter> on acpi0 86 battery0: <ACPI Control Method Battery> on acpi0 87 acpi_tz0: <Thermal Zone> on acpi0 88 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 89 atkbd0: <AT Keyboard> irq 1 on atkbdc0 90 kbd0 at atkbd0 91 atkbd0: [GIANT-LOCKED] 92 atkbd0: [ITHREAD] 93 psm0: <PS/2 Mouse> irq 12 on atkbdc0 94 psm0: [GIANT-LOCKED] 95 psm0: [ITHREAD] 96 psm0: model IntelliMouse, device ID 3 97 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 98 fdc0: [FILTER] 99 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi 0 100 sio0: type 16550A 101 sio0: [FILTER] 102 cpu0: <ACPI CPU> on acpi0 103 powernow0: <PowerNow! K7> on cpu0 104 pmtimer0 on isa0 105 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcefff,0xcf000-0xcf7ff,0xdb000-0xd bfff,0xdc000-0xdffff pnpid ORM0000 on isa0 106 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 107 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode 108 ppc0: FIFO with 16/16/16 bytes threshold 109 ppbus0: <Parallel port bus> on ppc0 110 ppbus0: [ITHREAD] 111 ppi0: <Parallel I/O> on ppbus0 112 plip0: <PLIP network interface> on ppbus0 113 plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag 114 lpt0: <Printer> on ppbus0 115 lpt0: Interrupt-driven port 116 ppc0: [GIANT-LOCKED] 117 ppc0: [ITHREAD] 118 sc0: <System console> at flags 0x100 on isa0 119 sc0: VGA <16 virtual consoles, flags=0x300> 120 sio1: configured irq 3 not in bitmap of probed irqs 0 121 sio1: port may not be enabled 122 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 123 ums0: <Logitech USB Receiver, class 0/0, rev 1.10/25.00, addr 2> on uhub0 124 ums0: 16 buttons and Z dir. 125 Timecounter "TSC" frequency 1788940443 Hz quality 800 126 Timecounters tick every 1.000 msec 127 firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) 128 firewire0: bus manager 0 (me) 129 ad0: 95396MB <Seagate ST9100823A 3.02> at ata0-master UDMA100 130 acd0: CDRW <QSI CD-RW/DVD-ROM SBW-241/VH04> at ata1-master UDMA33 131 Trying to mount root from ufs:/dev/ad0s2a -- www.nealhogan.net www.lambdaserver.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?ab7b49bc0903231304s7b99689et1f4c1fca4efc4bec>