Date: Sun, 12 Mar 2017 09:52:38 +0100 From: "Ronald Klop" <ronald-lists@klop.ws> To: freebsd-arm@freebsd.org Subject: ubldr.bin on sheevaplug (11-STABLE) Message-ID: <op.ywzb90jdkndu52@53556c9c.cm-6-6b.dynamic.ziggo.nl>
next in thread | raw e-mail | index | archive | help
Hello,
I just build a new 11-STABLE for my Sheevaplug. (BTW, it feels a lot mor=
e =
stable the last two or three months. I can still create UFS corruption o=
n =
my usb-stick, but it does not crash that often anymore.)
Back to the subject. I just tried ubldr.bin again. Previous attempts gav=
e =
no output and just hang. But now I get an error.
This is what I did:
----------------------------------------------------------- START
# 09:40:06 root@sheeva2 [/boot]
nandtool erase dev=3D/dev/gnand0s.fbsd-boot
# 09:40:15 root@sheeva2 [/boot]
dd if=3Dubldr.bin of=3D/dev/gnand0s.fbsd-boot bs=3D2k conv=3Dsync
120+1 records in
121+0 records out
247808 bytes transferred in 0.251712 secs (984489 bytes/sec)
# 09:40:43 root@sheeva2 [/boot]
shutdown -r now
<... snip ...>
Rebooting...
=C3=BE
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE
U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock =3D 400Mhz , TClock =3D 200Mhz
DRAM CAS Latency =3D 5 tRP =3D 5 tRAS =3D 18 tRCD=3D6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x200000, size 0x600000
6291456 bytes read: OK
## Starting application at 0x00900000 ...
data abort
pc : [<0092a0c0>] lr : [<00919fe4>]
sp : 005fe43c ip : 0093a950 fp : 005fe454
r10: 00000000 r9 : 0093de48 r8 : 00938ce8
r7 : 01badab1 r6 : 00938ceb r5 : 00938ce8 r4 : 00000000
r3 : 00000000 r2 : 00938ce8 r1 : 00000001 r0 : 0093bfb8
Flags: Nzcv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
----------------------------------------------------------- END
The commands are the same as when I install kernel.bin. I only substitut=
ed =
the if=3D value of dd with ubldr.bin.
Any ideas?
Can I provide more information?
Regards,
Ronald.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?op.ywzb90jdkndu52>