Date: Wed, 22 Aug 2001 20:51:17 -0500 From: William Guynes <wguynes@mav.net> To: "Justin T. Gibbs" <gibbs@scsiguy.com> Cc: freebsd-scsi@freebsd.org Subject: Re: sysinstall won't read drive, even though scsi controller is detected Message-ID: <v9o8otcqk08bh1qimj7ucrqah63sjvr7pv@smtp.prodigy.net> In-Reply-To: <200108220349.f7M3nkY06271@aslan.scsiguy.com> References: <6a26otk39br425aoqeofiv9gt592hbet3h@smtp.prodigy.net> <200108220349.f7M3nkY06271@aslan.scsiguy.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, 21 Aug 2001 21:49:46 -0600, "Justin T. Gibbs" <gibbs@scsiguy.com> wrote: [snip!] >At this point, can you hit "Scoll Lock" and PgUP to see if there are >any additional messages output by the ahc driver? I was not aware of that ability. Thanks. The entire FreeBSD boot information appears further down in this email. >You might also try one of the 4.4-RC floppies to see if a newer >kernel probes your devices better. After seeing the full boot info, I'm not entirely sure that's the case. This is what grabs my attention in it. >(ahc0:A:5:0): refuses synchronous negotiation, Using asynchronous transfers "da0" is begin detected. It just flew by too fast before and was erased. >Full firmware information for the Baracudda would be good to know >too. It's a hardly front-end model. They probably don't even make it anymore. I would think it would have been supported for ages. >BTW, what aic7xxx driver version are you using under Mandrake? Debian, actually: I'm giving the Debian boot info, trimmed down to SCSI relevant items only, and below that is the full FreeBSD boot info. Note: sda=SeagateHD and sdb=JazDrive, so ignore sdb errors. >kernel: (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 0/10/0 >kernel: (scsi0) Wide Channel, SCSI ID=15, 16/255 SCBs >kernel: (scsi0) Cables present (Int-50 YES, Int-68 NO, Ext-68 NO) >kernel: (scsi0) Downloading sequencer code... 422 instructions downloaded >kernel: scsi: <fdomain> Detection failed (no card) >kernel: NCR53c406a: no available ports found >kernel: sym53c416.c: Version 1.0.0 >kernel: Failed initialization of WD-7000 SCSI card! >kernel: IBM MCA SCSI: Version 3.2 >kernel: IBM MCA SCSI: No Microchannel-bus present --> Aborting. >kernel: This machine does not have any IBM MCA-bus >kernel: or the MCA-Kernel-support is not enabled! >kernel: megaraid: v1.11 (Aug 23, 2000) >kernel: aec671x_detect: >kernel: 3w-xxxx: tw_findcards(): No cards found. >kernel: scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4 >kernel: <Adaptec AHA-294X Ultra SCSI host adapter> >kernel: scsi : 1 host. >kernel: (scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15. >kernel: Vendor: SEAGATE Model: ST19171N Rev: 0019 >kernel: Type: Direct-Access ANSI SCSI revision: 02 >kernel: Detected scsi disk sda at scsi0, channel 0, id 3, lun 0 >kernel: (scsi0:0:5:0) Using asynchronous transfers. >kernel: Vendor: iomega Model: jaz 1GB Rev: G.60 >kernel: Type: Direct-Access ANSI SCSI revision: 02 >kernel: Detected scsi removable disk sdb at scsi0, channel 0, id 5, lun 0 >kernel: (scsi0:0:7:0) Synchronous at 10.0 Mbyte/sec, offset 15. >kernel: Vendor: NEC Model: CD-ROM DRIVE:462 Rev: 1.13 >kernel: Type: CD-ROM ANSI SCSI revision: 02 >kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 7, lun 0 >kernel: scsi : detected 1 SCSI cdrom 2 SCSI disks total. >kernel: Uniform CD-ROM driver Revision: 3.11 >kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783112 [8683 MB] [8.7 GB] >kernel: sdb : READ CAPACITY failed. >kernel: sdb : status = 1, message = 00, host = 0, driver = 28 >kernel: sdb : extended sense code = 2 >kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. >kernel: Partition check: >kernel: sda: sda1 sda2 sda3 >kernel: sdb:scsidisk I/O error: dev 08:10, sector 0 >kernel: unable to read partition table FreeBSD boot: >BTX loader 1.00 BTX version is 1.01 >avail memory = 58757120 (57300K bytes) >Preloaded elf kernel "kernel" at 0xc0672000. >Intel Pentium detected, installing workaround for F00F bug >md1: Malloc disk >npx0: <math processor> on motherboard >npx0: INT 16 interface >pcib0: <Host to PCI bridge> on motherboard >pci0: <PCI bus> on pcib0 >isab0: <Intel 82371AB PCI to ISA bridge> at device 1.0 on pci0 >isa0: <ISA bus> on isab0 >atapci: <Intel PIIX4 ATA33 controller> port 0xe00-0xe00f at device 1.1 on pic0 >ata0: at 0x1f0 irq14 on atapci0 >ata1: at 0x170 irq15 on atapci0 >uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd800-0xd81f irq 12 at device 1.2 on pci0 >usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 >usb0: USB revision 1.0 >uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub0: 2 ports with 2 removable, self powered >chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 1.3 on pci0 >pci0: <S3 ViRGE VX graphics accelerator> at 9.0 irq 12 >ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xd400-0xd4ff mem 0xdf800000-0xdf800fff irq 10 at device 10.0 on pci0 >aic7880: Wide Channel A, SCSI Id=15, 16/255 SCBs >ed0: <NE2000 PCI Ethernet (ProLAN) port 0xd000-0xd01f irq 11 at device 11.0 on pci0 >ed0: address 00:20:78:11:81:95, type NE2000 (16-bit) >fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 >fdc0: FIFO enabled, 8 bytes threshold >atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 >kbd0 at atkbd0 >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >sc0: <System console> at flags 0x100 on isa0 >sc0: VGA <16 virtual consoles, flags=0x300> >sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >sio0: type 16550A >sio1 at port 0x2f8-0x2ff irq 3 on isa0 >sio1: type 16550A >ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 >ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode >ppc0: FIFO with 16/16/16 bytes threshold >plip0: <PLIP network interface> on ppbus0 >Waiting 15 seconds for SCSI devices to settle >(ahc0:A:5:0): refuses synchronous negotiation, Using asynchronous transfers >Mounting root from ufs:/dev/md0c >da0: at ahc0 bus 0 target 3 lun 0 >da0: <SEAGATE ST19171N 0019> Fixed Direct Access SCSI-2 device >da0: <20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled >da0: 8683MB (17783112 512 byte sectors: 255H 63S/T 1106C) >cd0 at ahc0 bus 0 target 7 lun 0 >cd0: <NEC CD-ROM DRIVE:462 1.13> Removable CD-ROM SCSI-2 device >cd0: 10.000MB/s transfers (10.000MHz, offset 15) >cd0: cd present [330674 x 2048 byte records] >da1 at ahc0 bus 0 target 5 lun 0 >da1: <iomega jaz 1GB G.60> Removable Direct Access SCSI-2 device >da1: 3.300MB/s transfers >da1: Attempt to query device size failed: NOT READY, >/stand/sysinstall running as init on vty0 -- William Guynes To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?v9o8otcqk08bh1qimj7ucrqah63sjvr7pv>