Date: Fri, 26 Jan 2001 17:50:51 -0500 From: Tim McMillen <timcm@umich.edu> To: Benjamin Ossei <ben@cahostnet.net>, questions@FreeBSD.ORG Subject: Re: New Kernel install Message-ID: <0101261750510H.25766@tim.elnsng1.mi.home.com> In-Reply-To: <20010126155251.5FFA536F9@sitemail.everyone.net> References: <20010126155251.5FFA536F9@sitemail.everyone.net>
next in thread | previous in thread | raw e-mail | index | archive | help
You are removing things from your kernel config file that you don't understand. That almost guarantees compile failure. Read /usr/src/sys/i386/conf/LINT I see at least the one error, the same as Doug made. You commented out da and scbus and those are required for USB. You also randomly commented out things in USB that may be required, but left others. You may also have commented out other things that are required, I don't know. The best policy is not to take anything out you aren't sure you don't need. If you don't know what you need, read LINT, and beyond that only take out one thing at a time. If it breaks your kernel compile then you needed that! :) As a side note re-read the handbook chapter on configureing a kernel. In the section on building a kernel it says that if you have not cvsupped your source you can use the 1st method. If you have cvsupped your source, you have to use the second method AFTER doing a make buildworld. The second method, make buildkernel KERNEL=MYKERNELNAME, etc SHOULD be able to be used without having updated sources and using make buildworld, but currently (as of last week) it is a little broken, so the 1st method of kernel compile has to be used if sources haven't been touched. That problem may have already been fixed. Tim On Friday January 26, 2001 10:52, Benjamin Ossei wrote: > This is the error I get at the end. > > .../../dev/ppbus/ppb_1284.c:705: unterminated string or character > constant .../../dev/ppbus/ppb_1284.c:702: unterminated `#if' > conditional > > > --- Benjamin Ossei <ben@cahostnet.net> > > > wrote: > >Anyoneone else has any suggestions to my problem? I've attached the > > configuration file. Thanks for your help. > > > >--- Benjamin Ossei <ben@cahostnet.net> > > > >> wrote: > >>Part: 1 > >><pre>Hi, > >> > >>I'm trying to compile a new kernel for my machine. I used the > >> GENERIC configuration as a starting point and added what I needed > >> and commented out what I didn't want. I was able to issue the > >> command /usr/sbin/config -g "newkernel" fine but when I > >> go to build the kernel with the make depend or just make I get a > >> stop error. The error indicates that there's unterminited string > >> or something to the effect and gives me this "#IF" for > >> the problem. I've gone through my kernel config and can not see > >> anything. I'm not very good at this I should also say. > >> > >>I'm using Freebsd 4.2-Current. This is my first custom kernel. > >> I've attached the file for your viewing and hopefully you can see > >> my problem. I included the options IPFIREWALL_DEFAULT_TO_ACCEPT > >> for now to get the machine up and running. I'll change this to > >> DENY once I"m done and recompile the kernel. > >> > >> > >>Thanks for your help. > >> > >> > >> > >>_____________________________________________________________ > >>========GET YOUR FREE E-MAIL============ > >><A HREF="http://freemail.cahostnet.net" > >> target="_new">http://freemail.cahostnet.net</A> Web Hosting <A > >> HREF="http://www.cahostnet.com" > >> target="_new">http://www.cahostnet.com</A> </pre>Part: 2 > >><pre># > >># GENERIC -- Generic kernel configuration file for FreeBSD/i386 > >># > >># For more information on this file, please read the handbook > >> section on # Kernel Configuration Files: > >># > >># <A > >> HREF="http://www.FreeBSD.org/handbook/kernelconfig-config.html" > >> target="_new">http://www.FreeBSD.org/handbook/kernelconfig-config. > >>html</A> # > >># The handbook is also available locally in /usr/share/doc/handbook > >># if you've installed the doc distribution, otherwise always see > >> the # FreeBSD World Wide Web server (<A > >> HREF="http://www.FreeBSD.org/)" > >> target="_new">http://www.FreeBSD.org/)</A> for the # latest > >> information. > >># > >># An exhaustive list of options and more detailed explanations of > >> the # device lines is also present in the ./LINT configuration > >> file. If you are > >># in doubt as to the purpose or necessity of a line, check first in > >> LINT. # > >># $FreeBSD: src/sys/i386/conf/FWKERNEL,v 1 2001/01/25 22:45 Ben > >> Ossei Exp $ > >> > >>machine i386 > >>cpu I386_CPU > >>cpu I486_CPU > >>cpu I586_CPU > >>cpu I686_CPU > >>ident FWKERNEL > >>maxusers 64 > >> > >># makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols > >> > >># options MATH_EMULATE #Support for x87 emulation > >>options INET #InterNETworking > >>options INET6 #IPv6 communications protocols > >>options FFS #Berkeley Fast Filesystem > >>options FFS_ROOT #FFS usable as root device [keep this!] > >>options SOFTUPDATES #Enable FFS soft updates support > >>options MFS #Memory Filesystem > >>options MD_ROOT #MD is a potential root device > >># options NFS #Network Filesystem > >># options NFS_ROOT #NFS usable as root device, NFS required > >># options MSDOSFS #MSDOS Filesystem > >>options CD9660 #ISO 9660 Filesystem > >>options CD9660_ROOT #CD-ROM usable as root, CD9660 required > >>options PROCFS #Process filesystem > >>options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] > >>options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI > >># options UCONSOLE #Allow users to grab the console > >>options USERCONFIG #boot -c editor > >>options VISUAL_USERCONFIG #visual boot -c editor > >>options KTRACE #ktrace(1) support > >>options SYSVSHM #SYSV-style shared memory > >>options SYSVMSG #SYSV-style message queues > >>options SYSVSEM #SYSV-style semaphores > >>options P1003_1B #Posix P1003_1B real-time extensions > >>options _KPOSIX_PRIORITY_SCHEDULING > >>options ICMP_BANDLIM #Rate limit bad replies > >>options KBD_INSTALL_CDEV #install a CDEV entry in /dev > >>options IPFIREWALL > >>options IPFIREWALL_VERBOSE > >>options IPDIVERT > >>options IPFIREWALL_DEFAULT_TO_ACCEPT > >>options IPFIREWALL_VERBOSE_LIMIT=100 > >>options IPFILTER > >>options IPFILTER_LOG > >> > >># To make an SMP kernel, the > >>next two are needed > >>options SMP # Symmetric MultiProcessor Kernel > >>options APIC_IO # Symmetric (APIC) I/O > >> > >>device isa > >>device eisa > >>device pci > >> > >># Floppy drives > >>device fdc0 at isa? port IO_FD1 irq 6 drq 2 > >>device fd0 at fdc0 drive 0 > >># device fd1 at fdc0 drive 1 > >> > >># ATA and ATAPI devices > >>device ata0 at isa? port IO_WD1 irq 14 > >>device ata1 at isa? port IO_WD2 irq 15 > >>device ata > >>device atadisk # ATA disk drives > >>device atapicd # ATAPI CDROM drives > >>device atapifd # ATAPI floppy drives > >>device atapist # ATAPI tape drives > >>options ATA_STATIC_ID #Static device numbering > >># options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices > >> > >># SCSI Controllers > >># device ahb # EISA AHA1742 family > >># device ahc # AHA2940 and onboard AIC7xxx devices > >># device amd # AMD 53C974 (Teckram DC-390(T)) > >># device isp # Qlogic family > >># device ncr # NCR/Symbios Logic > >># device sym # NCR/Symbios Logic (newer chipsets) > >># options SYM_SETUP_LP_PROBE_MAP=0x40 > >> # Allow ncr to attach legacy NCR devices when > >> # both sym and ncr > >>are configured > >> > >># device adv0 at isa? > >># device adw > >># device bt0 at isa? > >># device aha0 at isa? > >># device aic0 at isa? > >> > >># device ncv # NCR 53C500 > >># device nsp # Workbit Ninja SCSI-3 > >># device stg # TMC 18C30/18C50 > >> > >># SCSI peripherals > >># device scbus # SCSI bus (required) > >># device da # Direct Access (disks) > >># device sa # Sequential Access (tape etc) > >># device cd # CD > >># device pass # Passthrough device (direct SCSI access) > >> > >># RAID controllers interfaced to the SCSI subsystem > >># device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID > >># device dpt # DPT Smartcache - See LINT for options! > >># device mly # Mylex AcceleRAID/eXtremeRAID > >> > >># RAID controllers > >># device ida # Compaq Smart RAID > >># device amr # AMI MegaRAID > >># device mlx # Mylex DAC960 family > >># device twe # 3ware Escalade > >> > >># atkbdc0 controls both the keyboard and the PS/2 mouse > >>device atkbdc0 at isa? port IO_KBD > >>device atkbd0 at atkbdc? irq 1 flags 0x1 > >>device psm0 at atkbdc? irq 12 > >> > >>device vga0 at isa? > >> > >># splash screen/screen saver > >>pseudo-device splash > >> > >># syscons is the default console driver, resembling an SCO console > >>device sc0 at isa? flags 0x100 > >> > >># Enable this and PCVT_FREEBSD for pcvt vt220 compatible console > >> driver # device vt0 at isa? > >># options XSERVER # support for X server on a vt console > >># options FAT_CURSOR # start with block cursor > >># If you have a ThinkPAD, uncomment this along with the rest of the > >> PCVT lines > >># options PCVT_SCANSET=2 # IBM keyboards are non-std > >> > >># Floating point support - do not disable. > >>device npx0 at nexus? port IO_NPX irq 13 > >> > >># Power management support (see LINT for more options) > >>device apm0 at nexus? disable flags 0x20 # Advanced Power > >> Management > >> > >># PCCARD (PCMCIA) support > >># device card > >># device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000 > >># device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable > >> > >># Serial (COM) ports > >>device sio0 at isa? port IO_COM1 flags 0x10 irq 4 > >>device sio1 at isa? port IO_COM2 irq 3 > >>device sio2 at isa? disable port IO_COM3 irq 5 > >>device sio3 at isa? disable port IO_COM4 irq 9 > >> > >># Parallel port > >>device ppc0 at isa? irq 7 > >>device ppbus # Parallel port bus (required) > >>device lpt # Printer > >># device plip # TCP/IP over parallel > >>device ppi # Parallel port interface device > >># device vpo # Requires scbus and da > >> > >> > >># PCI Ethernet NICs. > >># device de # DEC/Intel DC21x4x (``Tulip'') > >>device fxp # Intel EtherExpress PRO/100B (82557, 82558) > >># device tx # SMC 9432TX (83c170 ``EPIC'') > >>device vx # 3Com 3c590, 3c595 (``Vortex'') > >># device wx # Intel Gigabit Ethernet Card (``Wiseman'') > >> > >># PCI Ethernet NICs that use the common MII bus controller code. > >># NOTE: Be sure to keep the 'device miibus' line in order to use > >> these NICs! device miibus # MII bus support > >>device dc # DEC/Intel 21143 and various workalikes > >># device pcn # AMD Am79C79x PCI 10/100 NICs > >># device rl # RealTek 8129/8139 > >># device sf # Adaptec AIC-6915 (``Starfire'') > >># device sis # Silicon Integrated Systems SiS 900/SiS 7016 > >># device ste # Sundance ST201 (D-Link DFE-550TX) > >># device tl # Texas Instruments ThunderLAN > >># device vr # VIA Rhine, Rhine II > >># device wb # Winbond W89C840F > >>device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') > >> > >># ISA Ethernet NICs. > >># device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 > >># device ex > >># device ep > >># device fe0 at isa? port 0x300 > >># WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really > >># exists only as a PCMCIA device, so there is no ISA attatement > >> needed # and resources will always be dynamically assigned by the > >> pccard code. # device wi > >># Aironet 4500/4800 802.11 wireless NICs. Note: the declaration > >> below will # work for PCMCIA and PCI cards, as well as ISA cards > >> set to ISA PnP # mode (the factory default). If you set the > >> switches on your ISA # card for a manually chosen I/O address and > >> IRQ, you must specify # those paremeters here. > >># device an > >># Xircom Ethernet > >># device xe > >># The probe order of these is presently determined by > >> i386/isa/isa_compat.c. # device ie0 at isa? port 0x300 irq 10 > >> iomem 0xd0000 > >># device le0 at isa? port 0x300 irq 5 iomem 0xd0000 > >># device lnc0 at isa? port 0x280 irq 10 drq 0 > >># device cs0 at isa? port 0x300 > >># device sn0 at isa? port 0x300 irq 10 > >> > >># Pseudo devices - the number indicates how many units to > >> allocated. pseudo-device loop # Network loopback > >>pseudo-device ether # Ethernet support > >># pseudo-device sl 1 # Kernel SLIP > >># pseudo-device ppp 1 # Kernel PPP > >># pseudo-device tun # Packet tunnel. > >>pseudo-device pty # Pseudo-ttys (telnet etc) > >>pseudo-device md # Memory "disks" > >>pseudo-device gif 4 # IPv6 and IPv4 tunneling > >>pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) > >> > >># The `bpf' pseudo-device enables the Berkeley Packet Filter. > >># Be aware of the administrative consequences of enabling this! > >>pseudo-device bpf #Berkeley packet filter > >> > >># USB support > >># device uhci # UHCI PCI->USB interface > >># device ohci # OHCI PCI->USB interface > >>device usb # USB Bus (required) > >>device ugen # Generic > >>device uhid # "Human Interface Devices" > >>device ukbd # Keyboard > >>device ulpt # Printer > >># device umass # Disks/Mass storage - Requires scbus and da > >>device ums # Mouse > >># device uscanner # Scanners > >># USB Ethernet, requires mii > >># device aue # ADMtek USB ethernet > >># device cue # CATC USB ethernet > >># device kue # Kawasaki LSI USB ethernet > >></pre> > > > >_____________________________________________________________ > >========GET YOUR FREE E-MAIL============ > >http://freemail.cahostnet.net > >Web Hosting http://www.cahostnet.com > > > > > >To Unsubscribe: send mail to majordomo@FreeBSD.org > >with "unsubscribe freebsd-questions" in the body of the message > > _____________________________________________________________ > ========GET YOUR FREE E-MAIL============ > http://freemail.cahostnet.net > Web Hosting http://www.cahostnet.com > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?0101261750510H.25766>