Date: Mon, 4 Nov 2002 17:25:00 +1000 (EST) From: User Raymond <raymond@one.com.au> To: freebsd-questions@freebsd.org Subject: Lava Computers Octopus-550 8-port serial Message-ID: <200211040725.gA47P0oQ040074@gw.one.com.au>
next in thread | raw e-mail | index | archive | help
We are attempting to use a Lava Computers Octopus-550 8-port serial on
4.7-RELEASE FreeBSD. Boot up gives the following (full dmesg follows):
IOAPIC #0 intpin 16 -> irq 2
puc0: <Lava Computers Octopus-550 8-port serial> port 0x9400-0x9407,
0x9000-0x9007,0x8c00-0x8c07,0x8800-0x8807 irq 2 at device 6.0 on pci5
sio2: configured irq 2 not in bitmap of probed irqs 0x200
sio2: type 16550A
sio3: configured irq 2 not in bitmap of probed irqs 0x200
sio3: type 16550A
sio4: configured irq 2 not in bitmap of probed irqs 0x200
sio4: type 16550A
etc...
Note that BIOS reports the device at irq 9.
Ray Newman
04 Nov 2002
---
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE #2: Mon Nov 4 16:36:04 EST 2002
root@qml.local:/usr/src/sys/compile/DUAL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (2392.95-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 1073741824 (1048576K bytes)
avail memory = 1041805312 (1017388K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 24 pins in IOAPIC #1
Programming 24 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu2 (AP): apic id: 2, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 3, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 4, version: 0x00178020, at 0xfec00000
io1 (APIC): apic id: 5, version: 0x00178020, at 0xfec80000
io2 (APIC): apic id: 6, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc0348000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 15 entries at 0xc00fde70
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 17 -> irq 5
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
IOAPIC #2 intpin 0 -> irq 9
IOAPIC #2 intpin 11 -> irq 10
pci2: <PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.14> port
0xb000-0xb01f mem 0xfc020000-0xfc03ffff,0xfc000000-0xfc01ffff irq 9 at device
9.0 on pci2
em0: Speed:N/A Duplex:N/A
asr0: <Adaptec Caching SCSI RAID> mem 0xf8000000-0xf9ffffff irq 10 at device
12.0 on pci2
asr0: major=154
asr0: ADAPTEC 2110S FW Rev. 380E, 1 channel, 256 CCBs, Protocol I2O
pcib3: <PCI to PCI bridge (vendor=1044 device=a500)> at device 12.1 on pci2
pci3: <PCI bus> on pcib3
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib4: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 0 -> irq 11
IOAPIC #1 intpin 1 -> irq 16
pci4: <PCI bus> on pcib4
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xc000-0xc0ff mem
0xfc120000-0xfc120fff irq 11 at device 7.0 on pci4
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xc400-0xc4ff mem
0xfc121000-0xfc121fff irq 16 at device 7.1 on pci4
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
pcib5: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 18 -> irq 17
IOAPIC #0 intpin 19 -> irq 18
pci5: <PCI bus> on pcib5
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x8000-0x803f mem
0xfb000000-0xfb01ffff,0xfb041000-0xfb041fff irq 17 at device 4.0 on pci5
fxp0: Ethernet address 00:10:dc:65:68:51
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <ATI Mach64-GR graphics accelerator> at 5.0 irq 18
puc0: <Lava Computers Octopus-550 8-port serial> port 0x9400-0x9407,
0x9000-0x9007,0x8c00-0x8c07,0x8800-0x8807 irq 2 at device 6.0 on pci5
sio2: configured irq 2 not in bitmap of probed irqs 0x200
sio2: type 16550A
sio3: configured irq 2 not in bitmap of probed irqs 0x200
sio3: type 16550A
sio4: configured irq 2 not in bitmap of probed irqs 0x200
sio4: type 16550A
sio5: configured irq 2 not in bitmap of probed irqs 0x200
sio5: type 16550A
puc1: <Lava Computers Octopus-550 8-port serial> port 0xa400-0xa407,
0xa000-0xa007,0x9c00-0x9c07,0x9800-0x9807 irq 2 at device 6.1 on pci5
sio6: configured irq 2 not in bitmap of probed irqs 0x200
sio6: type 16550A
sio7: configured irq 2 not in bitmap of probed irqs 0x200
sio7: type 16550A
sio8: configured irq 2 not in bitmap of probed irqs 0x200
sio8: type 16550A
sio9: configured irq 2 not in bitmap of probed irqs 0x200
sio9: type 16550A
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,
0-0x7 irq 2 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 5
orm0: <Option ROMs> at iomem 0xc0000-0xca7ff,0xcc000-0xd1fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to deny, logging disabled
DUMMYNET initialized (011031)
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
acd0: CDROM <LTN526> at ata1-master PIO4
sa0 at ahc1 bus 0 target 0 lun 0
sa0: <SONY SDX-400C 0702> Removable Sequential Access SCSI-2 device
sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da0 at asr0 bus 0 target 0 lun 0
da0: <ADAPTEC RAID-1 380E> Fixed Direct Access SCSI-2 device
da0: Tagged Queueing Enabled
da0: 70007MB (143374336 512 byte sectors: 255H 63S/T 8924C)
Mounting root from ufs:/dev/da0s1a
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200211040725.gA47P0oQ040074>