Date: Thu, 31 Aug 2000 21:18:21 +0100 (BST) From: Nick Hibma <n_hibma@qubesoft.com> To: Christophe Prevotaux <chris@hexanet.fr> Cc: freebsd-hardware@FreeBSD.org Subject: Re: [HELP] USB , Gateway Solo 2150 and CURRENT Message-ID: <Pine.BSF.4.20.0008312117390.32581-100000@henny.webweaving.org> In-Reply-To: <200008311223.OAA02849@proton.hexanet.fr>
next in thread | previous in thread | raw e-mail | index | archive | help
If there is no switch in your BIOS that makes the message go away, you are out of luck until FreeBSD has full PCI enumeration (or whatever it is called) support. Nick On Thu, 31 Aug 2000, Christophe Prevotaux wrote: > > I am running CURRENT on my Gateway Solo 2150 Laptop > > among the problems I have > > uhci0 keeps telling me this: > > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> at device 7.2 on pci0 > uhci0: Invalid irq 255 > uhci0: Please switch on USB support and switch PNP-OS to 'No' in BIOS > > > However I have no option to switch on or off USB support in my Laptop BIOS > > I can it seems set on or off the PNP thing even though it is not called that > way > in the PhoenixBios ( it is called Other/Win95/Win98-2000 i think :)) > > > How can do to make my USB support work ? > > > I also still have the problem of my PCMCIA-Cardbus DLINK DFE 660TX ethernet > card > that is not supported under FreeBSD , but it work very well under Linux > I wonder if someone could not port the Linux driver under FreeBSD ? > > > below is my full dmesg in the event it could help somebody answer my queries :) > > Copyright (c) 1992-2000 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.0-CURRENT #0: Mon Aug 28 19:25:26 CEST 2000 > root@xxxx.hexanet.fr:/usr/obj/usr/src/sys/ZIPPY > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (501.14-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x683 Stepping = 3 > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,P > AT,PSE36,MMX,FXSR,XMM> > real memory = 167706624 (163776K bytes) > avail memory = 159285248 (155552K bytes) > Preloaded elf kernel "kernel" at 0xc0386000. > Preloaded userconfig_script "/boot/kernel.conf" at 0xc038609c. > Pentium Pro MTRR support enabled > md0: Malloc disk > apm0: <APM BIOS> on motherboard > apm0: found APM BIOS v1.2, connected at v1.2 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pci0: <Intel 82443BX (440 BX) host to PCI bridge> at 0.0 > pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <ATI Mobility-1 graphics accelerator> at 0.0 irq 9 > isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on > pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> at device 7.2 on pci0 > uhci0: Invalid irq 255 > uhci0: Please switch on USB support and switch PNP-OS to 'No' in BIOS > device_probe_and_attach: uhci0 attach returned 6 > pci0: <Intel 82371AB Power management controller> at 7.3 > pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> irq 9 at device 8.0 on pci0 > pcic-pci0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC > pci int + CSC serial isa irq] > pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> irq 9 at device 8.1 on pci0 > pcic-pci1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC > pci int + CSC serial isa irq] > pci0: <unknown card> (vendor=0x1102, dev=0x8938) at 9.0 irq 5 <- unknown ? > pci0: <unknown card> (vendor=0x11c1, dev=0x0448) at 10.0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 on isa0 > pcic0: Polling mode > pccard0: <PC Card bus -- kludge version> on pcic0 > pccard1: <PC Card bus -- kludge version> on pcic0 > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > unknown: <PNP0303> can't assign resources > unknown: <PNP0501> can't assign resources > unknown: <PNP0400> can't assign resources > unknown: <PNP0700> can't assign resources > ad0: 11513MB <TOSHIBA MK1214GAP> [23392/16/63] at ata0-master using UDMA33 > acd0: CDROM <CRN-8241B> at ata1-master using PIO4 > Mounting root from ufs:/dev/ad0s1a > pccard: card inserted, slot 0 > logo_saver: no suitable graphics mode <-- here is another problem I have :) > anyone ? > module_register_init: MOD_LOAD (logo_saver, c11d7b3c, 0) error 19 > ed1 at port 0x240-0x25f irq 3 slot 0 on pccard0 > ed1: address 00:00:e8:7f:0f:34, type NE2000 (16 bit) > > -- > -- > =================================================================== > Christophe Prevotaux Email: chris@hexanet.fr > HEXANET SARL URL: http://www.hexanet.fr/ > Z.A Farman Sud Tel: +33 (0)3 26 79 30 05 > 9 rue Roland Coffignot Direct: +33 (0)3 26 79 08 02 > BP415 Fax: +33 (0)3 26 79 30 06 > 51689 Reims Cedex 2 > FRANCE > =================================================================== > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-hardware" in the body of the message > -- Qube Software, Ltd. Private: n_hibma@qubesoft.com n_hibma@webweaving.org n_hibma@freebsd.org http://www.qubesoft.com/ http://www.etla.net/~n_hibma/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.20.0008312117390.32581-100000>