Date: Sun, 27 Oct 1996 21:07:30 -0500 From: Andrew Herdman <andrew@why.whine.com> To: freebsd-chat@freebsd.org Subject: strange ncr problems Message-ID: <Pine.BSF.3.95.961027210353.8129A-100000@why>
next in thread | raw e-mail | index | archive | help
Just a question about the ncr driver in the 2.2-960801-SNAP. I don't have much access to the machine but the following happens some times at bootup...... ignore the config screen..... Thanks for any advice... Andrew % dmesg No lpt0 0xffffffff 7 -1 0x0 0 0 0x0 Yes lpt1 0xffffffff -1 -1 0x0 0 1 0x0 Yes mse0 0x23c 5 -1 0x0 0 0 0x0 Yes Device port irq drq iomem iosize unit flags enabled psm0 0x60 12 -1 0x0 0 0 0x0 No ed0 0x280 5 -1 0xd8000 0 0 0x0 Yes ed1 0x300 10 -1 0xd8000 0 1 0x0 Yes ie0 0x360 7 -1 0xd0000 0 0 0x0 Yes ep0 0x300 10 -1 0x0 0 0 0x0 Yes fe0 0x300 -1 -1 0x0 0 0 0x0 Yes ix0 0x300 10 -1 0xd0000 32768 0 0x0 Yes le0 0x300 5 -1 0xd0000 0 0 0x0 Yes lnc0 0x280 10 0 0x0 0 0 0x0 Yes ze0 0x300 5 -1 0xd8000 0 0 0x0 Yes zp0 0x300 10 -1 0xd8000 0 0 0x0 Yes npx0 0xf0 13 -1 0x0 0 0 0x0 Yes apm0 0x0 -1 -1 0x0 0 0 0x0 No config> quit avail memory = 30519296 (29804K bytes) Probing for devices on PCI bus 0: chip0 <generic PCI bridge (vendor=8086 device=1250 subclass=0)> rev 3 on pci0:0 chip1 <generic PCI bridge (vendor=8086 device=7000 subclass=1)> rev 1 on pci0:7:0 pci0:7:1: Intel Corporation, device=0x7010, class=storage (ide) [no driver assigned] vga0 <VGA-compatible display device> rev 3 on pci0:10 ncr0 <ncr 53c810 scsi> rev 1 int a irq 11 on pci0:12 ncr0 waiting for scsi devices to settle (ncr0:2:0): "NEC D3827 0410" type 0 fixed SCSI 2 sd0(ncr0:2:0): Direct-Access sd0(ncr0:2:0): FAST SCSI-2 100ns (10 Mb/sec) offset 8. 1033MB (2116800 512 byte sectors) Probing for devices on the ISA bus: sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA color <16 virtual consoles, flags=0x0> ed0 not found at 0x280 ed1 at 0x300-0x31f irq 10 on isa ed1: address 00:c0:a8:4e:33:78, type NE2000 (16 bit) fe0 not probed due to I/O address conflict with ed1 at 0x300 sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A sio2: disabled, not probed. sio3: disabled, not probed. lpt0 not found at 0xffffffff lpt1 not found at 0xffffffff mse0 at 0x23c irq 5 on isa psm0: disabled, not probed. fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: NEC 72065B fd0: 1.44MB 3.5in wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 1 (atapi): <FX410A/J05>, removable, intr, iordis wdc1 not found at 0x170 bt0 not found at 0x330 uha0 not found at 0x330 aha0 not found at 0x330 aic0 not found at 0x340 nca0 not found at 0x1f88 nca1 not found at 0x350 sea0 not found wt0 not probed due to I/O address conflict with ed1 at 0x300 mcd0 not probed due to I/O address conflict with ed1 at 0x300 matcdc0 not found at 0x230 scd0 not found at 0x230 ie0 not found at 0x360 ep0 not probed due to I/O address conflict with ed1 at 0x300 ix0 not probed due to I/O address conflict with ed1 at 0x300 le0 not probed due to I/O address conflict with ed1 at 0x300 lnc0 not found at 0x280 ze0 not probed due to I/O address conflict with ed1 at 0x300 zp0 not probed due to I/O address conflict with ed1 at 0x300 npx0 on motherboard npx0: INT 16 interface apm0: disabled, not probed. changing root device to sd0a spec_getpages: I/O read error vm_fault: pager input (probably hardware) error, PID 30 failure uid 0 on /: out of inodes pid 30 (hostname), uid 0: exited on signal 11 ncr0: SCSI phase error fixup: CCB already dequeued (0xf0d73c00) ncr0: restart (ncr dead ?). sd0(ncr0:2:0): UNIT ATTENTION info?:ffffffff asc:29,0 sd0(ncr0:2:0): Power on, reset, or bus device reset occurred , retries:3 sd0(ncr0:2:0): FAST SCSI-2 100ns (10 Mb/sec) offset 8. sd0(ncr0:2:0): NOT READY info?:ffffffff asc:4,1 sd0(ncr0:2:0): Logical unit is in process of becoming ready , retries:2 sd0(ncr0:2:0): NOT READY info?:ffffffff asc:4,1 sd0(ncr0:2:0): Logical unit is in process of becoming ready , retries:1
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.95.961027210353.8129A-100000>