Date: Sun, 28 Mar 1999 11:35:44 +0200 (MET DST) From: =?ISO-8859-1?Q?Mikko_Ty=F6l=E4j=E4rvi?= <mikko@securitydynamics.com> To: "Kenneth D. Merry" <ken@plutotech.com> Cc: freebsd-scsi@FreeBSD.ORG Subject: Re: ZIP drive probe problems Message-ID: <Pine.GSO.4.05.9903281128490.19322-100000@spirit.dynas.se> In-Reply-To: <199903260013.RAA89750@panzer.plutotech.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 25 Mar 1999, Kenneth D. Merry wrote: > > Oops, that last patch had a little syntax problem. Try this one instead. > Done. Here is dmesg output from boot -v, with and without disc inside the ZIP drive. The second one is ok, the first is not. Just let me know if there is anything else I should try, or if you need more information. /Mikko Mikko Tyo"la"ja"rvi________________________________mikko@securitydynamics.com SecurityDynamics ---------------------------------------------------------------------- dmesg, no disc present (The ZIP is target 5 @ aha0) intel_piix_status: primary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 0 status: 04 from port: 0000e002 intel_piix_status: secondary master/slave sample = 5, master/slave recovery = 4 intel_piix_status: secondary master fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled intel_piix_status: secondary master/slave sample = 5, master/slave recovery = 4 intel_piix_status: secondary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 1 status: 04 from port: 0000e00a found-> vendor=0x8086, dev=0x7112, revid=0x01 class=0c-03-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=d, irq=14 map[0]: type 4, range 32, base 0000d800, size 5 found-> vendor=0x8086, dev=0x7113, revid=0x01 class=06-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 chip2: <Intel 82371AB Power management controller> rev 0x01 on pci0.1.3 found-> vendor=0x102b, dev=0x0519, revid=0x01 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 1, range 32, base e6800000, size 14 map[1]: type 3, range 32, base e7800000, size 23 vga0: <Matrox MGA 2064W graphics accelerator> rev 0x01 int a irq 10 on pci0.11.0 found-> vendor=0x1000, dev=0x0001, revid=0x11 class=01-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[0]: type 4, range 32, base 0000d400, size 8 map[1]: type 1, range 32, base e6000000, size 8 ncr0: <ncr 53c810a fast10 scsi> rev 0x11 int a irq 11 on pci0.12.0 ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo ncr0: single-ended, open drain IRQ driver Probing for devices on the ISA bus: atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa sc0 on isa sc0: fb0 kbd0 sc0: VGA color <16 virtual consoles, flags=0x0> ed0 at 0x300-0x31f irq 15 on isa ed0: address 00:80:c8:1c:ed:e1, type NE2000 (16 bit) bpf: ed0 attached atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa kbd0: atkbd0, AT 101/102 (2), config:0x10000, flags:0x3d0000 psm0: current command byte:0047 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 90 03 3c psm: status 90 03 3c psm: status 90 03 3c psm: status 00 00 3c psm: data 08 00 00 psm: data 08 00 00 psm: status 00 02 64 psm0 irq 12 on isa psm0: model Generic PS/2 mouse, device ID 0, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1: irq maps: 0x1 0x9 0x1 0x1 sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in wdc0: disabled, not probed. ppc: parallel port found at 0x378 ppc0: 0x87 - 0xc 0x0 0x2 0x10 0x0 0x0 0x5 0x0 0x0 0x8b 0x1f 0xc 0x28 0xab 0x0 0x0 0x0 0x0 0x0 0x0 0x7 0x0 0x0 0xfc 0x0 0x1 0xde 0xfe 0xbe 0x23 0x25 0x43 0x62 ppc0: ECP+EPP SPP ppc0 at 0x378 irq 7 on isa ppc0: W83877AF chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold ppb0: IEEE1284 device found /NIBBLE/NIBBLE_ID/Extensibility Link Probing for PnP devices on ppbus0: ppbus0: <Hewlett-Packard HP LaserJet 4ML> HP ENHANCED PCL5,PJL,POSTSCRIPT nlpt0: <generic printer> on ppbus 0 nlpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 plip: irq 7 plip0: <PLIP network interface> on ppbus 0 bpf: lp0 attached aha0 at 0x330-0x333 irq 9 drq 6 on isa aha0: AHA-1540/1542 64 head BIOS FW Rev. 1.2 (ID=41) SCSI Host Adapter, SCSI ID 7, 16 CCBs vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xf00b8000 size:32k gran:32k, buf:0x0 size:0k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff npx0 on motherboard npx0: INT 16 interface i586_bzero() bandwidth = 175070028 bytes/sec bzero() bandwidth = 88401697 bytes/sec imasks: bio c0080040, tty c003101a, net c0068080 BIOS Geometries: 0:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 1:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 2:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 3:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 4:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 5:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 6:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 7:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 0 accounted for Device configuration finished. Intel Pentium detected, installing workaround for F00F bug bpf: tun0 attached bpf: lo0 attached Waiting 15 seconds for SCSI devices to settle ncr0: restart (scsi reset). (probe3:ncr0:0:3:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe3:ncr0:0:3:0): ILLEGAL REQUEST asc:24,0 (probe3:ncr0:0:3:0): Invalid field in CDB (probe12:aha0:0:5:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe12:aha0:0:5:0): error code 0 pass0 at ncr0 bus 0 target 0 lun 0 pass0: <HP C3323-300 4084> Fixed Direct Access SCSI-2 device pass0: Serial Number US42900MK4 pass0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled pass1 at ncr0 bus 0 target 3 lun 0 pass1: <NEC CD-ROM DRIVE:222 3.0i> Removable CD-ROM SCSI-2 device pass1: 8.064MB/s transfers (8.064MHz, offset 8) pass2 at ncr0 bus 0 target 6 lun 0 pass2: <QUANTUM FIREBALL SE4.3S PJ09> Fixed Direct Access SCSI-2 device pass2: Serial Number 334731211806 pass2: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled pass3 at aha0 bus 0 target 5 lun 0 pass3: <IOMEGA ZIP 100 J.02> Removable Direct Access SCSI-2 device pass3: 3.300MB/s transfers da1 at ncr0 bus 0 target 6 lun 0 da1: <QUANTUM FIREBALL SE4.3S PJ09> Fixed Direct Access SCSI-2 device da1: Serial Number 334731211806 da1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled da1: 4110MB (8418816 512 byte sectors: 255H 63S/T 524C) cd0 at ncr0 bus 0 target 3 lun 0 cd0: <NEC CD-ROM DRIVE:222 3.0i> Removable CD-ROM SCSI-2 device cd0: 8.064MB/s transfers (8.064MHz, offset 8) cd0: cd present [322265 x 2048 byte records] da0 at ncr0 bus 0 target 0 lun 0 da0: <HP C3323-300 4084> Fixed Direct Access SCSI-2 device da0: Serial Number US42900MK4 da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled da0: 1003MB (2056008 512 byte sectors: 64H 32S/T 1003C) Considering FFS root f/s. changing root device to da0s1a (da2:aha0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (da2:aha0:0:5:0): error code 0 (da2:aha0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (da2:aha0:0:5:0): error code 0 (da2:aha0:0:5:0): got CAM status 0x2cc (da2:aha0:0:5:0): SCSI status 0x2 (da2:aha0:0:5:0): fatal error, failed to attach to device (da2:aha0:0:5:0): lost device (da2:aha0:0:5:0): removing device entry da0s1: type 0xa5, start 63, end = 2040254, size 2040192 : OK da1s1: type 0xa5, start 0, end = 8418815, size 8418816 : OK ffs_mountfs: superblock updated for soft updates Linux-ELF exec handler installed splash: image decoder found: green_saver ---------------------------------------------------------------------- And with disc: intel_piix_status: primary master fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled intel_piix_status: primary master/slave sample = 5, master/slave recovery = 4 intel_piix_status: primary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 0 status: 04 from port: 0000e002 intel_piix_status: secondary master/slave sample = 5, master/slave recovery = 4 intel_piix_status: secondary master fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled intel_piix_status: secondary master/slave sample = 5, master/slave recovery = 4 intel_piix_status: secondary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 1 status: 04 from port: 0000e00a found-> vendor=0x8086, dev=0x7112, revid=0x01 class=0c-03-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=d, irq=14 map[0]: type 4, range 32, base 0000d800, size 5 found-> vendor=0x8086, dev=0x7113, revid=0x01 class=06-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 chip2: <Intel 82371AB Power management controller> rev 0x01 on pci0.1.3 found-> vendor=0x102b, dev=0x0519, revid=0x01 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 1, range 32, base e6800000, size 14 map[1]: type 3, range 32, base e7800000, size 23 vga0: <Matrox MGA 2064W graphics accelerator> rev 0x01 int a irq 10 on pci0.11.0 found-> vendor=0x1000, dev=0x0001, revid=0x11 class=01-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[0]: type 4, range 32, base 0000d400, size 8 map[1]: type 1, range 32, base e6000000, size 8 ncr0: <ncr 53c810a fast10 scsi> rev 0x11 int a irq 11 on pci0.12.0 ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo ncr0: single-ended, open drain IRQ driver Probing for devices on the ISA bus: atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa sc0 on isa sc0: fb0 kbd0 sc0: VGA color <16 virtual consoles, flags=0x0> ed0 at 0x300-0x31f irq 15 on isa ed0: address 00:80:c8:1c:ed:e1, type NE2000 (16 bit) bpf: ed0 attached atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa kbd0: atkbd0, AT 101/102 (2), config:0x10000, flags:0x3d0000 psm0: current command byte:0047 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 90 03 3c psm: status 90 03 3c psm: status 90 03 3c psm: status 00 00 3c psm: data 08 00 00 psm: data 08 00 00 psm: status 00 02 64 psm0 irq 12 on isa psm0: model Generic PS/2 mouse, device ID 0, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1: irq maps: 0x1 0x9 0x1 0x1 sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in wdc0: disabled, not probed. ppc: parallel port found at 0x378 ppc0: 0x87 - 0xc 0x0 0x2 0x10 0x0 0x0 0x5 0x0 0x0 0x8b 0x1f 0xc 0x28 0xab 0x0 0x0 0x0 0x0 0x0 0x0 0x7 0x0 0x0 0xfc 0x0 0x1 0xde 0xfe 0xbe 0x23 0x25 0x43 0x62 ppc0: ECP+EPP SPP ppc0 at 0x378 irq 7 on isa ppc0: W83877AF chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold ppb0: IEEE1284 device found /NIBBLE/NIBBLE_ID/Extensibility Link Probing for PnP devices on ppbus0: ppbus0: <Hewlett-Packard HP LaserJet 4ML> HP ENHANCED PCL5,PJL,POSTSCRIPT nlpt0: <generic printer> on ppbus 0 nlpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 plip: irq 7 plip0: <PLIP network interface> on ppbus 0 bpf: lp0 attached aha0 at 0x330-0x333 irq 9 drq 6 on isa aha0: AHA-1540/1542 64 head BIOS FW Rev. 1.2 (ID=41) SCSI Host Adapter, SCSI ID 7, 16 CCBs vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xf00b8000 size:32k gran:32k, buf:0x0 size:0k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff npx0 on motherboard npx0: INT 16 interface i586_bzero() bandwidth = 175070028 bytes/sec bzero() bandwidth = 88409512 bytes/sec imasks: bio c0080040, tty c003101a, net c0068080 BIOS Geometries: 0:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 1:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 2:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 3:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 4:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 5:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 6:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 7:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 0 accounted for Device configuration finished. Intel Pentium detected, installing workaround for F00F bug bpf: tun0 attached bpf: lo0 attached Waiting 15 seconds for SCSI devices to settle ncr0: restart (scsi reset). (probe3:ncr0:0:3:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe3:ncr0:0:3:0): ILLEGAL REQUEST asc:24,0 (probe3:ncr0:0:3:0): Invalid field in CDB (probe12:aha0:0:5:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe12:aha0:0:5:0): error code 0 pass0 at ncr0 bus 0 target 0 lun 0 pass0: <HP C3323-300 4084> Fixed Direct Access SCSI-2 device pass0: Serial Number US42900MK4 pass0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled pass1 at ncr0 bus 0 target 3 lun 0 pass1: <NEC CD-ROM DRIVE:222 3.0i> Removable CD-ROM SCSI-2 device pass1: 8.064MB/s transfers (8.064MHz, offset 8) pass2 at ncr0 bus 0 target 6 lun 0 pass2: <QUANTUM FIREBALL SE4.3S PJ09> Fixed Direct Access SCSI-2 device pass2: Serial Number 334731211806 pass2: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled pass3 at aha0 bus 0 target 5 lun 0 pass3: <IOMEGA ZIP 100 J.02> Removable Direct Access SCSI-2 device pass3: 3.300MB/s transfers da1 at ncr0 bus 0 target 6 lun 0 da1: <QUANTUM FIREBALL SE4.3S PJ09> Fixed Direct Access SCSI-2 device da1: Serial Number 334731211806 da1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled da1: 4110MB (8418816 512 byte sectors: 255H 63S/T 524C) cd0 at ncr0 bus 0 target 3 lun 0 cd0: <NEC CD-ROM DRIVE:222 3.0i> Removable CD-ROM SCSI-2 device cd0: 8.064MB/s transfers (8.064MHz, offset 8) cd0: cd present [322265 x 2048 byte records] da0 at ncr0 bus 0 target 0 lun 0 da0: <HP C3323-300 4084> Fixed Direct Access SCSI-2 device da0: Serial Number US42900MK4 da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled da0: 1003MB (2056008 512 byte sectors: 64H 32S/T 1003C) da2 at aha0 bus 0 target 5 lun 0 da2: <IOMEGA ZIP 100 J.02> Removable Direct Access SCSI-2 device da2: 3.300MB/s transfers da2: 96MB (196608 512 byte sectors: 64H 32S/T 96C) Considering FFS root f/s. changing root device to da0s1a da0s1: type 0xa5, start 63, end = 2040254, size 2040192 : OK da1s1: type 0xa5, start 0, end = 8418815, size 8418816 : OK ffs_mountfs: superblock updated for soft updates Linux-ELF exec handler installed splash: image decoder found: green_saver To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.05.9903281128490.19322-100000>