Date: Mon, 17 Jun 2002 17:47:07 +0900 From: Hiroharu Tamaru <tamaru@myn.rcast.u-tokyo.ac.jp> To: freebsd-hardware@freebsd.org Subject: 3ware Escalade 7810 with old M/B: parity error Message-ID: <sa68z5e8f78.wl@gin.myn.rcast.u-tokyo.ac.jp>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hi,
I am trying to setup 3ware Escalde 7810 with somewhat old mother
board. The M/B is ASUS P2B-DS, equipped with 440BX chipset and with
dual Pentium II (450MHz). It has 4 32bit PCI slots and 2 ISA slots.
The 4.5-RELEASE install floppies paniced on the way.
I tried netbooting with -STABLE kernel as of May 8,
and now it boots (using GENERIC kernel, or SMP enabled kernel)
but then the screen is full of error messages.
When I boot, I keep on getting
"PCI parity error: Reseat card, move card or buggy device present."
message a few times a second from the twe driver, but the RAID drives
seem to be working as far as I can see; things mounts fine, I can
read/write to the array. Write test shows some 20-30MB/s in single
drive JBOD mode using Western Digital ATA-100 disk.
I don't get any errors if I boot off a DOS floppy, or a DOS (not
windows..) partition _on the array_. And again files can be
read/written fine. But this may just be that they don't show errors
anyway..
If I plug this card into some newer M/B, things work fine without any
error messages. For this I tried 32bit slots and 64bit slots; they
both worked without any error messages. This is another dual CPU
(Athlone MP 1500+) machine, if that matters.
The 7810 hardware is the newer version without the recalled
deficiency, and the firmware on the card is the newer release of Rev
7.4. I downloaded the image and had flashed them on.
The BIOS on the M/B is most recent too; although it dates back as far
as 07/04/00 (Rev 1013 beta, or Rev 1012b).
The PCI slot used is chosen so that 7810 does not share irq with any
other device, but I even shuffled them arround many times, to double
check that they are not loose or improperly seated.
So, all that said, I am suspecting if this could be due to pluging a
64bit PCI card into an old 32bit only PCI M/B. Is there any way to
fix or work around this? or is this a REAL error that need a newer M/B?
dmesg is attached at the end.
Thanks in advance.
--
Hiroharu Tamaru.
[-- Attachment #2 --]
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-PRERELEASE #0: Tue May 14 01:10:08 JST 2002
tamaru@myn.rcast.u-tokyo.ac.jp:/w/4src/src/sys/compile/TWE
Calibrating clock(s) ... TSC clock: 451002898 Hz, i8254 clock: 1193129 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (451.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping = 2
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 268423168 (262132K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00476000 - 0x0fff4fff, 263712768 bytes (64383 pages)
avail memory = 256962560 (250940K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
IOAPIC #0 intpin 16 -> irq 11
IOAPIC #0 intpin 17 -> irq 5
IOAPIC #0 intpin 19 -> irq 10
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00f9f10
bios32: Entry = 0xf0530 (c00f0530) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x730
pnpbios: Found PnP BIOS data at 0xc00fd360
pnpbios: Entry = f0000:d390 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 000f8190
Preloaded elf kernel "kernel.new" at 0xc044c000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000602c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 7 entries at 0xc00f0d20
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e4000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000d800, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=10
map[20]: type 1, range 32, base 0000d400, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 0000e800, size 4
found-> vendor=0x9005, dev=0x001f, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000d000, size 8
map[14]: type 1, range 64, base e1000000, size 12
found-> vendor=0x13c1, dev=0x1001, revid=0x01
class=01-04-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000b800, size 4
map[14]: type 1, range 32, base e0800000, size 4
map[18]: type 1, range 32, base e0000000, size 23
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base df800000, size 12
map[14]: type 1, range 32, base 0000b400, size 6
map[18]: type 1, range 32, base df000000, size 20
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x102b, dev=0x0521, revid=0x01
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base e3000000, size 24
map[14]: type 1, range 32, base e2000000, size 14
map[18]: type 1, range 32, base e1800000, size 23
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G200 AGP graphics accelerator> (vendor=0x102b, dev=0x0521) at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd800
ata0: mask=03 ostat0=00 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=00 stat1=00
ata0: devices=00
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd808
ata1: mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=00
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 10 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 4.3 on pci0
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xe1000000-0xe1000fff irq 10 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
using shared irq10.
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
twe0: <3ware Storage Controller> port 0xb800-0xb80f mem 0xe0000000-0xe07fffff,0xe0800000-0xe080000f irq 5 at device 11.0 on pci0
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: AEN: <soft reset>
twe0: 8 ports, Firmware FE7X 1.04.00.024, BIOS BE7X 1.07.02.008
twe0: Monitor ME7X 1.01.00.034, PCB Rev3 , Achip V3.20 , Pchip V1.30
twe0: port 0: WDC WD800AB-32BTA0 76319MB
twe0: port 1: WDC WD800AB-32BTA0 76319MB
twe0: port 2: WDC WD800AB-32BTA0 76319MB
twe0: port 5: WDC WD800AB-32BTA0 76319MB
twe0: port 6: WDC WD800AB-32BTA0 76319MB
twe0: port 7: WDC WD800AB-32BTA0 76319MB
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb400-0xb43f mem 0xdf000000-0xdf0fffff,0xdf800000-0xdf800fff irq 11 at device 12.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:90:27:c1:bf:5e
fxp0: PCI IDs: 8086 1229 8086 000c 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xcc000-0xccfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-51, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 5, 6, 7, 10, 11, 12, 14, 15, apic_imen: 0x00ff2305
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
2:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
3:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
4:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
5:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 6800c460, tty 6300109a, net 6700189a
bpf: sl0 attached
bpf: faith0 attached
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
twe0: PCI parity error: Reseat card, move card or buggy device present.twed0: <JBOD, Normal> on twe0
twed0: 76319MB (156301488 sectors)
Creating DISK twed0
twed1: <JBOD, Normal> on twe0
twed1: 76319MB (156301488 sectors)
Creating DISK twed1
twed2: <JBOD, Normal> on twe0
twed2: 76319MB (156301488 sectors)
Creating DISK twed2
twed3: <JBOD, Normal> on twe0
twed3: 76319MB (156301488 sectors)
Creating DISK twed3
twed4: <JBOD, Normal> on twe0
twed4: 76319MB (156301488 sectors)
Creating DISK twed4
twed5: <JBOD, Normal> on twe0
twed5: 76319MB (156301488 sectors)
Creating DISK twed5
twe0: command interrupt
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: unexpected status bit(s) 800000<PCIPERR>
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.Mounting root from nfs:
NFS ROOT: 10.22.17.5:/w/proot
start_init: trying /sbin/init
twe0: unexpected status bit(s) 800000<PCIPERR>
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?sa68z5e8f78.wl>