Date: Sun, 08 Jan 2006 21:12:46 +0100 From: Roman Dewald <romad@gmx.de> To: lvcargnini@ieee.org Cc: freebsd-hardware@freebsd.org Subject: Re: Dlink DWL-G520+ Message-ID: <1136751166.811.8.camel@urka.gonduras.ru> In-Reply-To: <ae36f8040601041905i4752a34aj@mail.gmail.com> References: <ae36f8040512281856v55ca67ffx@mail.gmail.com> <1136141981.675.30.camel@urka.gonduras.ru> <ae36f8040601041904r3f21c4d7r@mail.gmail.com> <ae36f8040601041905i4752a34aj@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, which driver have you converted? Did you use the Windows XP driver from the supplied CD? I had had problems with all drivers except the Windows XP driver. I run FreeBSD 6.0-RELEASE and did noticed any problem with unstable connection. I think the unstable connection may have following reason: You did not used the Windows XP driver for the conversion As for the connection speed I suggest you to check this: a) Configuration of the pf. Checker whether traffic shapping at your pf configuration is enabled. b)Check the configuration of your AP If it is possible I will suggest you to try the WLAN connection under Windows in order to determine that your hardware (card + AP) works correctly. If it works ok, I will suggest you to disable the firewall and try to establish a connection without the firewall. Regards, Roman Am Donnerstag, den 05.01.2006, 01:05 -0200 schrieb Luís Cargnini: > i forget i use pf firewall i trie with it and worked a little bit i > must mantain the firewall or remove it. > On 05/01/06, Luís Cargnini <lvcargnini@gmail.com> wrote: > > ok did this all but link seems unstable and i dont get much speed > > above 7~12k betwen ap and pc, how could i improve this one. Second > > system seems to have "weeping" "ic ic ic " my mouse and my system make > > some pauses, my processor achieve at least 17% of processing in idle > > mode, how to fix this things ? > > and my link crash sometimes. > > > > On 01/01/06, Roman Dewald <romad@gmx.de> wrote: > > > > > > > Hi i have an Dlink DWL-G520+ as following: > > > > ndis0@pci0:9:0: class=0x028000 card=0x3b041186 chip=0x9066104c rev=0x00 hdr=0x00 > > > > vendor = 'Texas Instruments (TI)' > > > > device = 'TNETW1130(ACX111) 802.11b/g Wireless Cardbus/PCI Adapter' > > > > class = network > > > > but it isn't working well, someone knows if exist an native driver or > > > > how i must proceed (walktrhough) to put this net device to work > > > I have had problems with this card and ndis driver under 5.4 Release. I > > > upgraded my system to the 6.0 Release and it worked fine. > > > > > > To get the driver working, you have first to bild a module for the > > > FreeBSD kernel from Windows drivers supplied with your card. > > > I used ndisgen to convert the driver. You will get some files after the > > > conversion you will a couple of files. > > > Then you can load the converted module with kldload +absolute path to > > > the converted module. You can check dmesg to ensure the module was > > > loaded successfully. You will see something like that: > > > > > > ndis0: <D-Link AirPlus G+ DWL-G520+ Wireless PCI Adapter> mem > > > 0xcfffa000-0xcfffbfff,0xcffc0000-0xcffdffff irq 19 at device 11.0 on > > > pci0 > > > > > > Afterwards you have to load the wlan_wep module to get the wep > > > encryption working. > > > Now you can configure the network settings with ifconfig. > > > > > > Roman > > > > > > > > > > Thanks && Regards > > > > Msc. Bsc. Luís Vitório Cargnini > > > > IEEE Member > > > > Mastering Degree student @ PUC-RS Electrical Engineer Faculty > > > > _______________________________________________ > > > > freebsd-hardware@freebsd.org mailing list > > > > http://lists.freebsd.org/mailman/listinfo/freebsd-hardware > > > > To unsubscribe, send any mail to "freebsd-hardware-unsubscribe@freebsd.org" > > > > > > > > > > > > > > > > -- > > Thanks && Regards > > Msc. Bsc. Luís Vitório Cargnini > > IEEE Member > > Mastering Degree student @ PUC-RS Electrical Engineer Faculty > > > > > -- > Thanks && Regards > Msc. Bsc. Luís Vitório Cargnini > IEEE Member > Mastering Degree student @ PUC-RS Electrical Engineer Faculty >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1136751166.811.8.camel>