Date: Sun, 21 May 2006 12:22:02 +0300 From: Yousef Raffah <yraffah@savola.com> To: Norberto Meijome <freebsd@meijome.net> Cc: freebsd-mobile@freebsd.org Subject: Re: FreeBSD 6 on Toshiba Tecra A4 Message-ID: <1148203322.25715.6.camel@localhost.savola.com> In-Reply-To: <20060419015334.43c6e36b@localhost> References: <1144676352.642.18.camel@redevil.savola.com> <20060414223802.65bb7762@localhost> <1145087149.633.3.camel@redevil.savola.com> <20060419015334.43c6e36b@localhost>
next in thread | previous in thread | raw e-mail | index | archive | help
--=-2kK+aDD7KWxyCAjNi7jZ
Content-Type: text/plain
Content-Transfer-Encoding: quoted-printable
On Wed, 2006-04-19 at 01:53 +1000, Norberto Meijome wrote:
> On Sat, 15 Apr 2006 10:45:49 +0300
> Yousef Raffah <yraffah@savola.com> wrote:
>=20
> > ACPI not working (working on Linux)
>=20
> doesn't work on my A2 either (does work, but the HD doens't realise it ha=
s gone
> to sleep and resumed and panic ensues on resume). disable acpi and use ap=
m,
> works fine.
> B
Hi,
I have disabled acpi and enabled apm in my kernel as
# Power management support (see NOTES for more options)
device apm
# Add suspend/resume support for the i8254.
device pmtimer
This what happens when I run apmd in debug mode:
# apmd -d -v
apmd[15918]: start
apmd: cannot open device file `/dev/apm': No such file or directory
How can I have /dev/apm?
Using 6.1-RC FreeBSD 6.1-RC #0: Sat Apr 29 17:16:15 AST 2006
This is my dmesg:
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 6.1-RC #0: Sat Apr 29 17:16:15 AST 2006
root@redevil:/usr/obj/usr/src/sys/LAPTOP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.86GHz (1862.02-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x6d8 Stepping =3D 8
Features=3D0xafe9f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C=
MOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
Features2=3D0x180<EST,TM2>
real memory =3D 1073606656 (1023 MB)
avail memory =3D 1041686528 (993 MB)
kbd1 at kbdmux0
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 12 Entries> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCIBIOS PCI-PCI bridge> irq 11 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <PCIBIOS PCI-PCI bridge> irq 10 at device 28.0 on pci0
pci2: <PCI bus> on pcib2
myk0: <Marvell 88E8053 Gigabit Ethernet Controller, Ver. 8.12.2.3> port
0xa000-0xa0ff mem 0xbc000000-0xbc003fff irq 11 at device 0.0 on pci2
myk0: Ethernet address: 00:a0:d1:bf:aa:e1
pcib3: <PCIBIOS PCI-PCI bridge> irq 11 at device 28.1 on pci0
pci3: <PCI bus> on pcib3
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port
0x1200-0x121f irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port
0x1220-0x123f irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port
0x1240-0x125f irq 11 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port
0x1260-0x127f irq 11 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem
0xf4000000-0xf40003ff irq 11 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib4: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pci6: <PCI bus> on pcib4
pci6: <network> at device 4.0 (no driver attached)
cbb0: <PCI-CardBus Bridge> mem 0x13000000-0x13000fff at device 6.0 on
pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: bad Vcc request. ctrl=3D0x17060a80, status=3D0xffffffff
cbb_power: 0V
fwohci0: <1394 Open Host Controller Interface> mem
0xb0000000-0xb00007ff,0xb0004000-0xb0007fff irq 11 at device 6.2 on pci6
fwohci0: OHCI version 1.10 (ROM=3D0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:08:0d:a0:d1:bf:aa:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=3D0xc000ffc0, gen=3D2, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <=3D 0, cable IRM =3D 0 (me)
firewire0: bus manager 0 (me)
fwohci0: phy int
pci6: <mass storage> at device 6.3 (no driver attached)
pci6: <base peripheral> at device 6.4 (no driver attached)
pcm0: <Intel ICH6 (82801FB)> port 0xe000-0xe0ff,0xe100-0xe13f mem
0xd0000000-0xd00001ff,0xd0000200-0xd00002ff irq 10 at device 30.2 on
pci0
pcm0: <Analog Devices AD1981B AC97 Codec>
pci0: <simple comms, generic modem> at device 30.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 SATA150 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1100-0x110f at device 31.2 on pci0
atapci0: failed to enable memory mapping!
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcffff,0xe0000-0xe1fff,0xe5000-0xe5fff,0xeb000-0xeffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0401> can't assign resources (port)
ums0: Mitsumi Electric Apple Optical USB Mouse, rev 1.10/1.08, addr 2,
iclass 3/1
ums0: 4 buttons and Z dir.
Timecounter "TSC" frequency 1862015465 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 76319MB <FUJITSU MHT2080AT 0022> at ata0-master UDMA100
acd0: DVDR <MATSHITADVD-RAM UJ-831S/1.40> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s2a
iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xb000b000-0xb000bfff irq 11 at
device 4.0 on pci6
iwi0: Ethernet address: 00:12:f0:63:ae:ca
iwi0: link state changed to UP
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
cbb0: bad Vcc request. ctrl=3D0x4e0a3b00, status=3D0x62617368
cbb_power: 0V
cbb0: bad Vcc request. ctrl=3D0x4e0a3b55, status=3D0x62617368
cbb_power: 1V
cbb0: bad Vcc request. ctrl=3D0x4e0a3b00, status=3D0x62617368
cbb_power: 0V
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
cbb0: Unsupported card type detected
ums0: at uhub0 port 1 (addr 2) disconnected
ums0: detached
ums0: Mitsumi Electric Apple Optical USB Mouse, rev 1.10/1.08, addr 2,
iclass 3/1
ums0: 4 buttons and Z dir.
--
Sincerely,
Yousef Raffah
Senior Systems Administrator
--
Aren't you using Firefox? Get it at http://www.getfirefox.com
--=-2kK+aDD7KWxyCAjNi7jZ
Content-Type: application/pgp-signature; name=signature.asc
Content-Description: This is a digitally signed message part
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (FreeBSD)
iD8DBQBEcDE6H9IXMb4e6CMRAluzAKCuwyhjK//COQrI7XcBFp1kJPRowACgtuB2
yqXhd3ZMwtZ35V/PN7w4Ob0=
=SRRh
-----END PGP SIGNATURE-----
--=-2kK+aDD7KWxyCAjNi7jZ--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1148203322.25715.6.camel>