Date: Sat, 1 Mar 2008 17:43:01 -0800 From: Cameron <cam@eleventhhourfx.com> To: freebsd-hardware@freebsd.org Subject: Re: can't boot MSI p6n-sli (nforce 650i) system Message-ID: <200803011743.01865.cam@eleventhhourfx.com> In-Reply-To: <Pine.LNX.4.64.0802281734240.7448@neo-zeon.de> References: <Pine.LNX.4.64.0802281734240.7448@neo-zeon.de>
next in thread | previous in thread | raw e-mail | index | archive | help
It would appear I have two separate problems. I removed the LSI Logic Megeraid 150-4 sata controller. FreeBSD will now boot and I can get to sysinstall. Ufortunately it sees no hard drives (I have a hard drive attached to the MCP51 motherboard's controller). I wanted to install the array, but neither problem is good. I've now tried FreeBSD 7.0 amd64 and i386 as well as 6.3 for i386. All of them get stuck right after the raid card is initialized. I've only tried 7.0 for amd64 without this card though. This is the error I get from the MCP51 controller with verbose logging: ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 I'm doing this from memory because I can't figure out how to get this information over a serial console (I've only done serial consoles on sparc, not on PC). But I'm pretty sure that's the error (at least the err=x01 is absolutely correct). I'm pretty sure I have the most up to date bios for this board. Thanks. -Cameron On Thursday 28 February 2008 5:34:58 pm you wrote: > Hello, > > I'm unable to successfully boot FreeBSD 7.0R for amd64 on my MSI p6n-sli > motherboard (nvidia 650i chipset). I don't have a dmesg to show at the the > moment (though I > may be able to get one). This is a quad core system > > Disabling apic doesn't help, in fact the boot process doesn't even get as > far when apic is disabled (it just gets stuck mounting md0 or something > like that). > Disabling acpi seems to have the same result as disabling apic. > > It gets stuck right after it brings up the remaining 3 cores (seems to > always bring them up in the order of 3, 1, and 2 if that matters). > > Just before bringing up the cores it detects my LSI Logic SATA 150-4 raid > controller (I doubt the controller itself is the problem, maybe it's an > issue with the amd64 > version of this controller). > > Turning on verbosity doesn't really seem to tell me anything more other > than after the 3 remaining cores are brought up, I get a single line > message along the lines > of: > > amr0: new geom (something very similiar to that). > > Where amr0 refers to the LSI Logic sata raid controller (obviously). > > Seems other people have had trouble with FreeBSD and the 650 chipset with > the nforce ide and/or sata controller. Interestingly if I reset the > machine without first > powering down and attempt to boot Linux, the boot gets stuck and fails > with this message slowly repeated over and over: > hda: interrupt lost > (hda is the first primary IDE drive of course) > > > This message ONLY happens if attempt to boot the FreeBSD 7.0R CD and > simply press the reset button (which seems to indicate it's not my raid > controller). I have not > got this message on this system prior to this. > > Interestingly I tried NetBSD 4.0 a little ways back and it seemed to have > trouble readin the disk geomtry of the first primary IDE drive (I believe > the FreeBSD driver > is based on the NetBSD driver or vice versa). > > Hope I've provided enough useful information (except a dmesg for now). > > Has anyone else had trouble with FreeBSD on nforce 650i based > motherboards? How about just my MSI p6n-sli board? Should I try FreeBSD > for i386 to see if that makes > any difference? > > Thanks! > > -Cameron
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200803011743.01865.cam>