Date: Sun, 18 Jan 2009 00:10:02 GMT From: "Robert J. Brown" <rjb@robertjbrown.com> To: freebsd-amd64@FreeBSD.org Subject: Re: amd64/129315: [boot] amd64 motherboard: Intel DG965WH motherboard compatibility with AMD64 Message-ID: <200901180010.n0I0A2OH051156@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR amd64/129315; it has been noted by GNATS.
From: "Robert J. Brown" <rjb@robertjbrown.com>
To: bug-followup@FreeBSD.org
Cc:
Subject: Re: amd64/129315: [boot] amd64 motherboard: Intel DG965WH motherboard compatibility with AMD64
Date: Sat, 17 Jan 2009 15:37:07 -0800
I tried this with 7.1-RELEASE and still have an issue but I do have an
important update.
At this point, I have just the bare board with a Core 2 Duo CPU and
ATA hard drive set to cable select primary position. I attached a
Plextor DVD/CD via USB. Nothing else is plugged in and I continue to
get a reboot about 1/3 of the way through the kernel boot process and
way before it mounts any disk partitions. It seems to indicate
something about an interrupt before the reboot but it flashes by too
quickly for me to see what the last message says.
I disabled EVERY peripheral in the BIOS (sound, firewire, LAN, serial,
parallel) and BOOM it works! The two other settings that I changed
from the first post are the video mode was changed from DVMT to FIXED
and I disabled "XD Technology" which is a link on the Security tab of
the BIOS. I was able to boot the 7.1-RELEASE and install the OS to the
hard drive. I then rebooted and turned on the peripherals one at a
time to figure out what the problem was. I narrowed it down to the
onboard LAN device. I now have everything else turned on except the
onboard LAN and I can boot and have a stable system.
Here are the BIOS settings that allow me to work properly (without LAN):
Advanced->Boot Configuration
Numlock On
Max CPUID Value Limit Disable
Display Setup Prompt On
Advanced->Peripheral Configuration
Serial Port Enable
Parallel Port Disable (haven't tried this since I don't use it)
Audio Enable
On-board LAN Disable
Onboard 1394 Enable
Advanced->Drive Configuration
ATA/IDE Mode Native
Configure SATA at AHCI (IDE works too)
SMART Enable
Hard Disk Pre-Delay No
Advanced->Floppy Configuration
Floppy Disable
Advanced->Video Configuration
DVMT Mode Fixed
IGD DVMT Memory 128MB
IGD Aperture Size 128MB
Primary Video Adaptor Auto
Advanced->Fan Control
Processor Zone Response Normal
Processor Zone Damping Normal
Automatic Fan Detection Disable
Advanced->Chipset Configuration
Memory Configuration
SDRAM Control Manual
CPC Override Disabled
Memory Frequency 800MHz
tCL 5
tRCD 5
tRP 5
tRASmin 15
PCI Express Config
Compliance Test Pattern Disable
PCI Latency Timer 32
HPET Disable
Advanced->USB Configuration
USB Ports Enable
USB Legacy Enable
Security
Expansion Card Text Disable
Chassis Intrusion Disable
XD Technology Disable
Intel Virtualization Technology Disable
Power
After Power Failure Power On
Wake on LAN from S5 Power On
Enhanced Intel SpeedStep Technology Enable
Intel Quick Resume Techology Disable
Wake system from S5 Disable
I also updated to the latest 1754 BIOS release and still have the
instant reboot if the LAN is enabled so this problem is true with the
latest FreeBSD release and the latest BIOS for this board.
The onboard LAN chip is an Intel 82566DC Gigabit Ethernet controller
so I suspect this problem is related to that driver.
Here is the dmesg output for the system where everything is running
except onboard LAN:
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #2: Sat Jan 17 14:31:36 PST 2009
root@:/usr/obj/usr/src/sys/SMOS0002
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz (1868.54-MHz K8-
class CPU)
Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
Features
=
0xbfebfbff
<
FPU
,VME
,DE
,PSE
,TSC
,MSR
,PAE
,MCE
,CX8
,APIC
,SEP
,MTRR
,PGE
,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20000800<SYSCALL,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
usable memory = 3185475584 (3037 MB)
avail memory = 3080007680 (2937 MB)
ACPI APIC Table: <INTEL DG965WH >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <INTEL DG965WH> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x20f0-0x20f7 mem
0xd0200000-0xd02fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
agp0: <Intel G965 SVGA controller> on vgapci0
agp0: detected 7676k stolen memory
agp0: aperture size is 256M
drm0: <Intel i965G> on vgapci0
info: [drm] AGP at 0xc0000000 256MB
info: [drm] Initialized i915 1.5.0 20060119
pci0: <simple comms> at device 3.0 (no driver attached)
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x20c0-0x20df
irq 16 at device 26.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x20a0-0x20bf
irq 21 at device 26.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem
0xd0304c00-0xd0304fff irq 18 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
usb2: USB revision 2.0
uhub2: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 4 ports with 4 removable, self powered
umass0: <PLEXTOR Corp. USB Storage Adapter, class 0/0, rev 2.00/0.00,
addr 2> on uhub2
axe0: <vendor 0x0b95 product 0x7720, class 255/255, rev 2.00/0.01,
addr 3> on uhub2
axe0: AX88772, bufsz 1536, boundary 64
miibus0: <MII bus> on axe0
ukphy0: <Generic IEEE 802.3u media interface> PHY 16 on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
axe0: WARNING: using obsoleted if_watchdog interface
axe0: WARNING: using obsoleted IFF_NEEDSGIANT flag
axe0: Ethernet address: 00:50:b6:04:21:fc
pcm0: <Intel 82801H High Definition Audio Controller> mem
0xd0300000-0xd0303fff irq 22 at device 27.0 on pci0
pcm0: [ITHREAD]
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
atapci0: <Marvell 88SX6101 UDMA133 controller> port 0x1018-0x101f,
0x1024-0x1027,0x1010-0x1017,0x1020-0x1023,0x1000-0x100f mem
0xd0100000-0xd01001ff irq 17 at device 0.0 on pci2
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pci5: <ACPI PCI bus> on pcib5
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x2080-0x209f
irq 23 at device 29.0 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x2060-0x207f
irq 19 at device 29.1 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x2040-0x205f
irq 18 at device 29.2 on pci0
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem
0xd0304800-0xd0304bff irq 23 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
usb6: USB revision 2.0
uhub6: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb6
uhub6: 6 ports with 6 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
fwohci0: <Texas Instruments TSB43AB22/A> mem 0xd0004000-0xd00047ff,
0xd0000000-0xd0003fff irq 19 at device 3.0 on pci6
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:90:27:00:01:b4:c0:17
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:90:27:b4:c0:17
fwe0: Ethernet address: 02:90:27:b4:c0:17
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:90:27:00:01:b4:c0:17 @ 0xfffe00000000,
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xbe1cc000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel AHCI controller> port 0x20e8-0x20ef,0x20fc-0x20ff,
0x20e0-0x20e7,0x20f8-0x20fb,0x2020-0x203f mem 0xd0304000-0xd03047ff
irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.10 controller with 6 ports detected
ata3: <ATA channel 0> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 1> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 2> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 3> on atapci1
ata6: [ITHREAD]
ata7: <ATA channel 4> on atapci1
ata7: [ITHREAD]
ata8: <ATA channel 5> on atapci1
ata8: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
on acpi0
sio0: type 16550A
sio0: [FILTER]
cpu0: <ACPI CPU> on acpi0
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
orm0: <ISA Option ROM> at iomem 0xcb800-0xcc7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based
forwarding disabled, defaultfirewire0: 1 nodes, maxhop <= 0, cable IRM
= 0 (me)
firewire0: bus manager 0 (me)
to deny, logging disabled
ad5: 152627MB <Seagate ST3160812A 3.AAJ> at ata2-slave UDMA100
pcm0: <HDA Codec: Sigmatel STAC9271D>
pcm0: <HDA Driver Revision: 20080420_0052>
SMP: AP CPU #1 Launched!
cd0 at umass-sim0 bus 0 target 0 lun 0
cd0: <PLEXTOR DVDR PX-716A 1.11> Removable CD-ROM SCSI-0 device
cd0: 40.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not
present - tray closed
Trying to mount root from ufs:/dev/ad5s1a
--
Robert J. Brown
rjb@robertjbrown.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200901180010.n0I0A2OH051156>