Date: Sun, 3 Oct 1999 10:45:39 -0400 (EDT) From: Kenneth Culver <culverk@culverk.student.umd.edu> To: freebsd-current@freebsd.org Subject: ata driver Message-ID: <Pine.BSF.4.10.9910031044520.267-100000@culverk.student.umd.edu>
next in thread | raw e-mail | index | archive | help
Alright, this is the dmesg that Soren asked for to help with the timeout
problem.
Copyright (c) 1992-1999 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #1: Sun Oct 3 10:43:26 EDT 1999
culverk@culverk.student.umd.edu:/usr/src/sys/compile/MYKERNEL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Xeon/Celeron (451.02-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping = 2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 134152192 (131008K bytes)
avail memory = 127344640 (124360K bytes)
Preloaded elf kernel "kernel" at 0xc029f000.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
WARNING: "bktr" is usurping "bktr"'s cdevsw[]
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vga-pci0: <VGA-compatible display device> at device 0.0 on pci1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
ata-pci0: <Intel PIIX4 IDE controller> at device 7.1 on pci0
ata-pci0: Busmastering DMA supported
ata0 at 0x01f0 irq 14 on ata-pci0
ata1 at 0x0170 irq 15 on ata-pci0
chip1: <UHCI USB controller> irq 11 at device 7.2 on pci0
intpm0: <Intel 82371AB Power management controller> at device 7.3 on pci0
intpm0: I/O mapped 5000
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 4000
pci0: unknown card (vendor=0x121a, dev=0x0002) at 13.0
pci0: unknown card (vendor=0x121a, dev=0x0002) at 15.0
bktr0: <BrookTree 878> irq 9 at device 17.0 on pci0
iicbb0: <I2C generic bit-banging driver> on bti2c0
iicbus0: <Philips I2C bus> on iicbb0 master-only
smbus1: <System Management Bus> on bti2c0
smb1: <SMBus general purpose I/O> on smbus1
bktr0: Hauppauge Model 61291 D110
Hauppauge WinCast/TV, Philips NTSC tuner, remote control.
pci0: unknown card (vendor=0x109e, dev=0x0878) at 17.1 irq 9
de0: <Digital 21140A Fast Ethernet> irq 10 at device 19.0 on pci0
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:c0:f0:1f:21:02
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus 0
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
vpo0: <Iomega VPI0 Parallel to SCSI interface> on ppbus 0
vpo0: EPP 1.9 mode
sb0 at port 0x220 irq 5 drq 1 on isa0
snd0: <SoundBlaster 16 4.16>
isa_compat: didn't get drq for sbxvi
sbxvi0 at port 0xffffffff drq 1 on isa0
isa_compat: didn't get ports for sbxvi
isa_compat: didn't get drq for sbxvi
snd0: <SoundBlaster 16 4.16>
WARNING: "snd" is usurping "snd"'s cdevsw[]
sbmidi0 at port 0x330 on isa0
snd0: <SoundBlaster MPU-401>
WARNING: "snd" is usurping "snd"'s cdevsw[]
opl0 at port 0x388 on isa0
snd0: <Yamaha OPL3 FM>
WARNING: "snd" is usurping "snd"'s cdevsw[]
ad0: <Maxtor 90845D4/GAS54112> ATA-4 disk at ata0 as master
ad0: 8063MB (16514064 sectors), 16383 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 0 depth queue, UDMA33
Creating DISK ad0
Creating DISK wd0
ad1: <Maxtor 84320D4/NAVX1920> ATA-3 disk at ata0 as slave
ad1: 4120MB (8438850 sectors), 8930 cyls, 15 heads, 63 S/T, 512 B/S
ad1: 16 secs/int, 0 depth queue, UDMA33
Creating DISK ad1
Creating DISK wd1
ad2: <FUJITSU MPC3064AT/6020> ATA-3 disk at ata1 as master
ad2: 6187MB (12672450 sectors), 13410 cyls, 15 heads, 63 S/T, 512 B/S
ad2: 16 secs/int, 0 depth queue, UDMA33
Creating DISK ad2
Creating DISK wd2
acd0: <CD-ROM 40X/AKU/U30> CDROM drive at ata1 as slave
, 128KB buffer, PIO
acd0: supported read types: CD-DA
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM 120mm data/audio disc loaded, unlocked
Creating DISK da0
da0 at vpo0 bus 0 target 6 lun 0
da0: <IOMEGA ZIP 100 D.09> Removable Direct Access SCSI-2 device
da0: Attempt to query device size failed: NOT READY, Medium not present
changing root device to wd1s1a
de0: enabling 10baseT port
Thanks
Kenneth Culver
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.9910031044520.267-100000>