Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 02 Mar 2009 21:43:59 +0200
From:      Alexander Motin <mav@mavhome.dp.ua>
To:        Elliot Schlegelmilch <elliot@schlegelmilch.org>
Cc:        FreeBSD-Current <freebsd-current@freebsd.org>
Subject:   Re: SATA disks suddenly stop working
Message-ID:  <49AC36FF.2080509@mavhome.dp.ua>
In-Reply-To: <20090302190759.GA95194@schlegelmilch.org>
References:  <go44ht$2i6a$1@FreeBSD.cs.nctu.edu.tw> <1235602472.00079680.1235592003@10.7.7.3> <1235658185.00079898.1235647801@10.7.7.3> <1235863381.00080963.1235851802@10.7.7.3> <49AAB0A6.3040304@mavhome.dp.ua> <20090302190759.GA95194@schlegelmilch.org>

next in thread | previous in thread | raw e-mail | index | archive | help
Elliot Schlegelmilch wrote:
> Alexander Motin wrote:
> 
> [snip]
> 
>>> ata2: <ATA channel 0> on atapci1
>>> ata2: AHCI reset...: 2
>>> ata2: SATA connect time=0ms
>>> ata2: ready wait time=0ms52 (12272 MB)
>>> ata2: software reset port 15...
>>> ata2: ahci_issue_cmd timeout: 100 of 100ms, status=00000001
>>> ata2: software reset set timeout
>>> ata2: software reset port 0...
>>> ata2: ahci_issue_cmd timeout: 100 of 100ms, status=00000001
>>> ata2: software reset set timeout
>>> ata2: SIGNATURE: ffffffff
>>> ata2: Unknown signature, assuming disk device
>>> ata2: AHCI reset done: devices=00000001
>>> ata2: [MPSAFE]
>>> ata2: [ITHREAD]
>>>
>>> One for each channel, up to ata7. 
>> Does it happen during boot or what do you mean by unable to reattach 
>> drive now?
> 
> Yes, I saw the above during boot. 
> 
> What I mean by unable to reattach is describing the old behavior:
> Sometimes my ad12 would fall off the bus, and I could usually retrieve
> it by 'atacontrol detach ata6; atacontrol attach ata6;'
> Now it's: ata6: still BUSY after softreset
> and attempting the detach/attach results in:
> 
> Tracing pid 12 tid 100007 td 0xffffff0001afb390
> device_get_parent() at device_get_parent+0x1
> ata_start() at ata_start+0x1c5
> ata_reinit() at ata_reinit+0x1dd
> ata_completed() at ata_completed+0x75
> softclock() at softclock+0x291
> intr_event_execute_handlers() at intr_event_execute_handlers+0x68
> ithread_loop() at ithread_loop+0xb2
> fork_exit() at fork_exit+0x12a
> fork_trampoline() at fork_trampoline+0xe
> --- trap 0, rip = 0, rsp = 0xfffffffe4004ad40, rbp = 0 ---
> 
> This isn't a huge deal, and is probably a red herring, as I suspect
> the disk is going bad at this point. This is running Feb 1 kernel, as
> I recall. However, it can and has stayed attached for weeks at a time
> before.

If it happens with kernel of Feb 1, then probably drive just becomes 
worse. It's not me. :)

>>> atapci0@pci0:0:31:1:    class=0x01018a card=0x948115d9 chip=0x269e8086 
>>> rev=0x09 hdr=0x00
>>>     vendor     = 'Intel Corporation'
>>>     device     = '631xESB/632xESB/3100 Ultra ATA Storage Controller'
>>>     class      = mass storage
>>>     subclass   = ATA
>>>
>>> The last known kernel which works was Dec 17, but trying to rebuild a
>>> kernel from that date doesn't see the SATA disks either (as the kernel
>>> which sees the disks zfs doesn't work.) Or perhaps I'm csup'ing
>>> incorrectly.
>> Haven't you tried to just touched reset sequence on 15.
> 
> Do you mean a kernel on Feb 15? Was there more that happened between
> 15th and the 22nd or so?

You have made something unreadable cutting and gluing two my sentences. 
:) Yes, there many happens between Feb 15 and 22.

>> When you succeed to boot, can you try to make some experiments against 
>> HEAD, may be some of them fix the problem:
>> 1) comment that line inside ata_ahci_issue_cmd():
>>     ATA_OUTL(ctlr->r_res2, ATA_AHCI_P_FBS + offset, (port << 8) | 
>> 0x00000001);
>>
>> 2) comment these lines inside ata_sata_phy_reset():
>>     if ((ATA_IDX_INL(ch, ATA_SCONTROL) & ATA_SC_DET_MASK) == 
>> ATA_SC_DET_IDLE)
>>     return ata_sata_connect(ch);
>>
>> 3) comment first that line inside ata_ahci_softreset():
>>     return (-1);
>>
>> Thanks.
>>
> 
> I'll try these patches and report back right after I freshen up my backups. :)

First one is already committed to the HEAD. It may be related to your 
problem.

-- 
Alexander Motin



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?49AC36FF.2080509>