Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 11 Feb 2004 10:49:42 -0500
From:      Sven Willenberger <sven@dmv.com>
To:        freebsd-current@freebsd.org
Subject:   Re: 5.2 Install CD doesn't detect all scsi drives
Message-ID:  <1076514582.22530.8.camel@lanshark.dmv.com>
In-Reply-To: <1076362711.19842.65.camel@lanshark.dmv.com>
References:  <1076192961.18071.10.camel@lanshark.dmv.com> <1076338994.19845.10.camel@lanshark.dmv.com> <20040209114753.L48001@carver.gumbysoft.com> <1076362711.19842.65.camel@lanshark.dmv.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, 2004-02-09 at 16:38, Sven Willenberger wrote:
> On Mon, 2004-02-09 at 14:51, Doug White wrote:
> > Try this. At the sysinstall menu, hit scroll lock, then arrow up and check
> > out the asr probe messages.  It'd be extra neat if you could capture them
> > with a serial console.
> > 
> Having issues outputting to console (minicom on another FreeBSD box)
> from the install CD so here is the output I copied instead:
> 
> asr0: <ADAPTEC Caching SCSI RAID> mem
> 0xfc000000-0xfdffffff,0xfb000000-0xfbffffff,0xf8300000-0xf82fffff irq24
> at device 1.0 on pci3
> asr0: major=154
> pcib3: device asr0 requested decoded memory range 0xf8300000-0xf83fffff
> pcib1: device asr0 requested decoded memory range 0xf8300000-0xf83fffff
> pcib3: device asr0 requested decoded memory range 0xfb000000-0xfb400000
> pcib1: device asr0 requested decoded memory range 0xfb000000-0xfb400000
> .
> .
> --other devices listed here
> .
> .
> (probe0:asr0:0:0:0): Data Overrun
> (probe0:asr0:0:0:0): Retrying Command
> (probe0:asr0:0:0:0): Data Overrun
> (probe0:asr0:0:0:0): Retrying Command
> (probe0:asr0:0:0:0): Data Overrun
> (probe0:asr0:0:0:0): Retrying Command
> (probe0:asr0:0:0:0): Data Overrun
> (probe0:asr0:0:0:0): Retrying Command
> (probe0:asr0:0:0:0): Data Overrun
> (probe0:asr0:0:0:0): error 5
> (probe0:asr0:0:0:0): Retries Exhausted
> pass0 at asr0 bus 1 target 1 lun 0
> pass0: <ADAPTEC RAID-5 3B05> Fixed DirectAccess SCSI-2 Device
> pass0: Serial Number +
> pass0: Tagged Queueing Enabled
> GEOM: create disk da0 dp=0xc6fd0850
> GEOM: new disk da0
> da0 at asr0 bus 1 target 1 lun 0
> da0: <ADAPTEC RAID-5 3B05> Fixed DirectAccess SCSI-2 Device
> da0: Serial Number +
> 
> 
> > Next, hit scroll lock to get the screen back, then go to Fixit, then
> > Shell. Run '/stand/camcontrol devlist -v' and paste us the output.  That
> > should show the two disk devices.
> > 
> 
> 
> /stand/camcontrol devlist -v
> scbus0 on asr0 bus 0:
> <  >			at scbus0 target -1 lun -1 ()
> scbus1 on asr0 bus 1:
> <ADAPTEC RAID-5 3B05>	at scbus1 target 1 lun 0 (da0,pass0)
> <  >			at scbus1 target -1 lun -1 ()
> scbus-1 on xpt0
> <  >			at scbus-1 target -1 lun -1 (xpt0)

To see if this was something specific to sysinstall, I installed
4.9-stable (which works fine in detecting everything), cvsupped
RELENG_5_1 went through the buildworld, etc (per UPDATING) and then went
to reboot. With the new kernel in place, (i.e. /boot/default/loader.conf
loads up with 5.1-P13 on screen) the lone drive is once again not found.
Actually the same error from Probe0 occurs, namely data overrun, and the
OS cannot be loaded (no root). Unfortunately, even though I enabled
console redirect in the bios, it stops outputting once the loader starts
(even though I enabled redirect after OS loads) so I don't have a good
capture (I redirect via direct cable to another FreeBSD box running
minicom). 

So it appears that unless this card is configured such that all the
drives on the motherboard are part of the RAID (since it is Zero
channel, changing what controller the drives are connected to is
immaterial), 5.x FreeBSD only sees those drives that are part of a RAID,
and not any solo disks/drives.

Where to go from here?



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1076514582.22530.8.camel>