Date: Mon, 17 Feb 1997 18:37:29 +0000 (GMT) From: Wei-Jou Chen <jou@nematic.ieo.nctu.edu.tw> To: freebsd-questions@FreeBSD.ORG Cc: jou@nematic.ieo.nctu.edu.tw Subject: [HELP] KINGMAX ethernet card Message-ID: <Pine.BSF.3.95.970217183204.378A-100000@chen>
index | next in thread | raw e-mail
Hello all,
I have a "KINGMAX" PCMCIA ethernet card. I don't know how to
configure the "ether offset" option in /etc/pccard.conf.
Is there a way to find the "ether offset" value out ?
Beside, I don't know how to configure the "config" option.
I would be very appreciated, if you can tell me how to write
/etc/pccard.conf.
Please reply to jou@nematic.ieo.nctu.edu.tw. Thanks.
The follwings are the output of "pccardc dumpcis".
--------------------------------------------------------------
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: dc 00 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 100nS, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 49 00 ff
Attribute memory device information:
Device number 1, type EEPROM, WPS = ON
Speed = 250nS, Memory block size = 512b, 1 units
Tuple #3, code = 0x21 (Functional ID), length = 2
000: 06 03
Network/LAN adapter - POST initialize - Card has ROM
Tuple #4, code = 0x15 (Version 1 info), length = 21
000: 04 01 4b 49 4e 47 4d 41 58 00 45 4e 31 30 54 32
010: 54 00 00 00 ff
Version = 4.1, Manuf = [KINGMAX],card vers = [EN10T2T]
Addit. info = [],[]
Tuple #5, code = 0x13 (Link target), length = 3
000: 43 49 53
Tuple #6, code = 0x1a (Configuration map), length = 5
000: 01 24 f8 03 03
Reg len = 2, config register addr = 0x3f8, last config = 0x24
Registers: XX------
Tuple #7, code = 0x1b (Configuration entry), length = 17
000: e0 81 1d 3f 55 4d 5d 06 86 46 26 fc 24 65 30 ff
010: ff
Config index = 0x20(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1 x 100mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Wait scale Speed = 1.5 x 10 us
Card decodes 4 address lines, 8 Bit I/O only
IRQ modes: Level
IRQ level = 4
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 20 08 ca 60 00 03 1f
Config index = 0x20
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 21 08 ca 60 20 03 1f
Config index = 0x21
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 22 08 ca 60 40 03 1f
Config index = 0x22
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 23 08 ca 60 60 03 1f
Config index = 0x23
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #12, code = 0x20 (Manufacturer ID), length = 4
000: 01 8a 00 01
PCMCIA ID = 0x8a01, OEM ID = 0x100
Tuple #13, code = 0x14 (No link), length = 0
Tuple #14, code = 0xff (Terminator), length = 0
2 slots found
-------------------------------------------------------------------
--Jou
== Wei-Jou Chen ( 陳威州 ) ==
== Email:jou@nematic.ieo.nctu.edu.tw ==
== Mail : No. 25, Lane 878, Nan-Ta Road, Hsinchu, Taiwan __o ==
== 新竹市南大路878巷25號 _\<,_, ==
== Fax/Data: +886-35-613285 Tel: +886-35-266575 . ..(*)/(*) ==
help
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.95.970217183204.378A-100000>