Date: Fri, 27 Aug 1999 16:02:56 -0600 From: Darren WIebe <dkwiebe@heartland.ab.ca> To: freebsd-mobile@freebsd.org Subject: GVC 33.6 PCMCIA modem (not initialized properly) Message-ID: <37C70B10.2B3DE859@heartland.ab.ca>
next in thread | raw e-mail | index | archive | help
Hello:
I just recently bought the above mentioned modem. I see that in the
pccard.conf file it mentions that modem except it calls it a C34+ rather
than the V34+ that it calls itself. Anyhow when I insert it it gives
the following erro message:
"Aug 27 15:40:06 thinkpad pccardd[51]: Card "CIRRUS LOGIC V34+ 33.6Kbps
MODEM"("CL-MD34XX") [3.07] [(null)] has function ID 2"
**It repeats this 3 times, then it repeats the following lines 3
times***
"Aug 27 15:40:06 thinkpad pccardd[51]: Resource allocation failure for
"CIRRUS LOGIC V34+ 33.6Kbps MODEM"("CL-MD34XX") [3.07] [(null)];
Reason specified CIS was not found"
This modem works under dos and linux, as a point of interest. I
searched through the mailing list archives and found a similar problem
that somebody else had quite a while ago. I tried the solution but
could not get it to work... I would really appreciate it if somebody
could let me know what I am doing wrong. And I would appreciate it if
you could CC the message to me, seeing that I am not sure that majordomo
has signed me up to the list yet.
TIA
Darren Wiebe
dkwiebe@hagenhomes.com
Here is my cisdump
Code 224 not found
Code 224 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 51
000: 05 01 43 49 52 52 55 53 20 4c 4f 47 49 43 20 56
010: 33 34 2b 20 33 33 2e 36 4b 62 70 73 20 4d 4f 44
020: 45 4d 00 43 4c 2d 4d 44 33 34 58 58 00 33 2e 30
030: 37 00 ff
Version = 5.1, Manuf = [CIRRUS LOGIC V34+ 33.6Kbps MODEM], card vers =
[CL-MD34XX]
Addit. info = [3.07]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: 4e 01 88 00
PCMCIA ID = 0x14e, OEM ID = 0x88
Tuple #4, code = 0x21 (Functional ID), length = 2
000: 02 01
Serial port/modem - POST initialize
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 24 00 01 13
Reg len = 2, config register addr = 0x100, last config = 0x24
Registers: XX--X---
Tuple #6, code = 0x1b (Configuration entry), length = 19
000: e0 81 9d 5f 55 4d 5d 0e 1e 05 fc 14 aa 60 f8 03
010: 07 24 28
Config index = 0x20(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1.2 x 100mA
Max current average over 1 second: 1.5 x 100mA
Power down supply current: 1 x 10mA
Wait scale Speed = 1.2 x 10 us
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3f8 block length = 0x8
IRQ modes: Level
IRQ level = 4
Max twin cards = 0
Misc attr: (Audio-BVD2) (Power down supported)
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 21 08 aa 60 f8 02 07
Config index = 0x21
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 22 08 aa 60 e8 03 07
Config index = 0x22
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 23 08 aa 60 e8 02 07
Config index = 0x23
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2e8 block length = 0x8
Tuple #10, code = 0x1b (Configuration entry), length = 6
000: 24 18 23 30 00 00
Config index = 0x24
Card decodes 3 address lines, 8 Bit I/O only
IRQ modes: Level
IRQs:
Tuple #11, code = 0x14 (No link), length = 0
Tuple #12, code = 0x0 (Null tuple), length = 3
000: 20 ff 24
Tuple #13, code = 0xff (Terminator), length = 0
2 slots found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?37C70B10.2B3DE859>