Date: Tue, 13 Feb 2007 09:09:22 +0900 From: Pyun YongHyeon <pyunyh@gmail.com> To: Joe Marcus Clarke <marcus@FreeBSD.org> Cc: current@FreeBSD.org Subject: Re: Constant stream of errors on msk0 Message-ID: <20070213000922.GA62412@cdnetworks.co.kr> In-Reply-To: <45D0BB41.9040505@FreeBSD.org> References: <45D0BB41.9040505@FreeBSD.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, Feb 12, 2007 at 02:08:49PM -0500, Joe Marcus Clarke wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > I recently upgraded my MacBook Pro from -STABLE to -CURRENT. I used to > be using the Marvell myk driver for my wired ethernet. This driver > worked fine. I'm now using the built-in msk driver, but this driver > causes the interface to report a constant stream of input errors. There Would you explain this input errors? > are no dmesg errors. However, network performance is dramatically > impacted. To the best of my knowledge, nothing has changed on the > switch side. > Does netstat(4) report any errors on msk? Does netstat(4) also show larger number of out-of-order TCP packets? > I am currently running: > > FreeBSD gyros.marcuscom.com 7.0-CURRENT FreeBSD 7.0-CURRENT #34: Fri Feb > 9 04:46:10 EST 2007 > marcus@gyros.marcuscom.com:/usr/obj/usr/src/sys/GYROS i386 > > I have a: > > mskc0: <Marvell Yukon 88E8053 Gigabit Ethernet> port 0x2000-0x20ff mem > 0x98200000-0x98203fff irq 16 at device 0.0 on pci2 > msk0: <Marvell Technology Group Ltd. Yukon EC Id 0xb6 Rev 0x02> on mskc0 > msk0: Ethernet address: 00:16:cb:92:bc:ad > miibus0: <MII bus> on msk0 > e1000phy0: <Marvell 88E1111 Gigabit PHY> PHY 0 on miibus0 > e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, > 1000baseTX-FDX, auto > mskc0: [FAST] > > msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=19a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> > inet6 fe80::216:cbff:fe92:bcad%msk0 prefixlen 64 scopeid 0x1 > inet x.x.x.x netmask 0xffffff00 broadcast 255.255.255.255 > ether 00:16:cb:92:bc:ad > media: Ethernet autoselect (1000baseTX <full-duplex,flag0,flag1>) > status: active > > mskc0@pci2:0:0: class=0x020000 card=0x532111ab chip=0x436211ab rev=0x22 > hdr=0x00 > vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' > device = 'Yukon 88E8053 PCI-E Gigabit Ethernet Controller (Copper)' > class = network > subclass = ethernet > > Any suggestions? Thanks. > > Joe > > - -- > Joe Marcus Clarke > FreeBSD GNOME Team :: gnome@FreeBSD.org > FreeNode / #freebsd-gnome > http://www.FreeBSD.org/gnome > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.4.5 (Darwin) > Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org > > iD8DBQFF0LtBb2iPiv4Uz4cRAp/cAKCViXEAU4BTXZVOr5rD8nJ2jZGVTwCeJ/9k > xJIxjTyUllvUpQG3CVVx8/A= > =DS5b > -----END PGP SIGNATURE----- -- Regards, Pyun YongHyeon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20070213000922.GA62412>