Date: Tue, 20 Dec 2005 23:10:18 -0700 From: Ken Gunderson <kgunders@teamcool.net> To: freebsd-amd64@freebsd.org Subject: Re: Tyan TA26, LSI 320-1, and FBSD6.0 Strangeness Message-ID: <20051220231018.5b383a39.kgunders@teamcool.net> In-Reply-To: <20051220160752.0f6dcc43.kgunders@teamcool.net> References: <20051220160752.0f6dcc43.kgunders@teamcool.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, 20 Dec 2005 16:07:52 -0700
Ken Gunderson <kgunders@teamcool.net> wrote:
> Hello List:
>
> I'm having a tough time w/a Tyan TA26, 320-1 and 6.0-RELEASE that
> I'm hoping y'all may be able to shed some light on. I create logical
> drives and install FBSD just fine. Then cvsup, buildworld,
> buildkernel, installkernel. Upon reboot the system drives (mirror) are
> in degraded mode and the raid0 drive (swap) is offline. MegaRAID is
> unable to rebuild the arrays. I've called LSI support and they're
> mystified as well.
[big snippage]
> E) Present Status:
>
> Interestingly enough, I am able to FORCE Physical Drive 1 back online
> and then "Check Consistency". Presently 21% complete so don't know if
> it will choke on error on not yet.
Update-
The consistency check did complete w/o any errors and rebooting all
logical drives are once again in "Optimal" state. For sake of
completeness heres the dmesg:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved. FreeBSD 6.0-RELEASE-p1 #0: Tue Dec 20 15:48:15 EST 2005
kgunders@portia.musicalartists.org:/usr/obj/usr/src/sys/PORTIA
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 244 (1794.11-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 2147418112 (2047 MB)
avail memory = 2063020032 (1967 MB)
ACPI APIC Table: <A M I OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 15 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 11 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 9 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci3: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 19
at device 0.0 on pci3 ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfeafd000-0xfeafdfff irq 19
at device 0.1 on pci3 ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
pci3: <display, VGA> at device 6.0 (no driver attached)
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xbc00-0xbc3f mem
0xfeafb000-0xfeafbfff,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on
pci3 miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface>
on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:e0:81:2f:8e:98
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9b0000-0xfc9bffff,0xfc9a0000-0xfc9affff irq 24 at device 9.0 on
pci2 miibus1: <MII bus> on bge0 brgphy0: <BCM5704 10/100/1000baseTX
PHY> on miibus1 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:2f:8e:d0
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9e0000-0xfc9effff,0xfc9d0000-0xfc9dffff irq 25 at device 9.1 on
pci2 miibus2: <MII bus> on bge1 brgphy1: <BCM5704 10/100/1000baseTX
PHY> on miibus2 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge1: Ethernet address: 00:e0:81:2f:8e:d1
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver
attached) pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci1: <ACPI PCI bus> on pcib3
amr0: <LSILogic MegaRAID 1.51> mem 0xff4f0000-0xff4fffff irq 29 at
device 4.0 on pci1 amr0: <LSILogic MegaRAID SCSI 320-1> Firmware 1L37,
BIOS G119, 64MB RAM pci0: <base peripheral, interrupt controller> at
device 11.1 (no driver attached) acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0 sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0 Timecounters tick every 1.000 msec
acd0: CDROM <QSI CD-ROM SCR-242/CXAC> at ata0-master UDMA33
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 66036MB (135241728 sectors) RAID 1 (optimal)
amrd1: <LSILogic MegaRAID logical drive> on amr0
amrd1: 8198MB (16789504 sectors) RAID 0 (optimal)
amrd2: <LSILogic MegaRAID logical drive> on amr0
amrd2: 140270MB (287272960 sectors) RAID 5 (optimal)
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/amrd0s1a
bge0: link state changed to UP
--
Best regards,
Ken Gunderson
Q: Because it reverses the logical flow of conversation.
A: Why is putting a reply at the top of the message frowned upon?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051220231018.5b383a39.kgunders>