Date: Fri, 12 Jun 2009 09:48:33 -0600 From: Kai Lockwood <kailockwood@gmail.com> To: freebsd-bugs@freebsd.org Subject: FreeBSD 7.0 isoonly CD boot fails Message-ID: <b5ef8d5c0906120848v48870590t1e25487729f6d4c6@mail.gmail.com> In-Reply-To: <4A050305.1010707@gmail.com> References: <4A050305.1010707@gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hello, Trying to install 7.0 from a bootonly CD on to a Integrity rx2600 . System crashes partway through the booting proces. Output below: fs0:\> efi\boot\bootia64.efi Consoles: EFI console Image base: 0x00000040fef70000 FreeBSD/ia64 EFI boot, Revision 1.2 (root@pluto1.freebsd.org, Sun Feb 24 21:12:16 UTC 2008) Loading /boot/defaults/loader.conf /boot/kernel/kernel data=3D0xb46ac0+0x3f308 syms=3D[0x8+0x7a820+0x8+0x6b072= ] / Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 8 seconds... Type '?' for a list of commands, 'help' for more detailed help. OK set hw.ata.atapi_dma=3D0 OK set hw.ata.ata_dma=3D0 OK set hw.ata.wc=3D0 OK boot Entering /boot/kernel/kernel at 0xe000000004070000... GDB: debug ports: uart GDB: current port: uart KDB: debugger backends: ddb gdb KDB: current backend: ddb Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 =A0 =A0 =A0 The Regents of the University of California. All rights reserve= d. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-RELEASE #0: Mon Feb 25 07:27:59 UTC 2008 =A0 root@pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC CPU: Madison (1300.00-Mhz Itanium 2) =A0Origin =3D "GenuineIntel" =A0Revision =3D 5 =A0Features =3D 0x1<LB> real memory =A0=3D 4273651712 (4075 MB) avail memory =3D 4067926016 (3879 MB) FPSWA Revision =3D 0x10012, Entry =3D 0xe0000040ffe60050 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0: SAPIC Id=3D0, SAPIC Eid=3D0 (BSP) cpu1: SAPIC Id=3D1, SAPIC Eid=3D0 acpi0: <HP> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: Sleep Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> iomem 0xff5c1004-0xff5c1007 on a= cpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 pci0: <ACPI PCI bus> on pcib0 ohci0: <NEC uPD 9210 USB controller> mem 0x80023000-0x80023fff irq 16 at de= vice0 ohci0: [GIANT-LOCKED] ohci0: [ITHREAD] usb0: OHCI version 1.0 usb0: <NEC uPD 9210 USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 3 ports with 3 removable, self powered ohci1: <NEC uPD 9210 USB controller> mem 0x80022000-0x80022fff irq 17 at de= vice0 ohci1: [GIANT-LOCKED] ohci1: [ITHREAD] usb1: OHCI version 1.0 usb1: <NEC uPD 9210 USB controller> on ohci1 usb1: USB revision 1.0 uhub1: <NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x80021000-0x800210ff irq 18= at 0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb2: EHCI version 0.95 usb2: companion controllers, 3 ports each: usb0 usb1 usb2: <NEC uPD 720100 USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: <NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2 uhub2: 5 ports with 5 removable, self powered atapci0: <SiI CMD 649 UDMA100 controller> port 0xd58-0xd5f,0xd64-0xd67,0xd5= 0-0x0 atapci0: [ITHREAD] atapci0: HW has secondary channel disabled ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] fxp0: <Intel 82550 Pro/100 Ethernet> port 0xd00-0xd3f mem 0x80020000-0x8002= 0fff0 miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> PHY 1 on miibus0 inphy0: =A010baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:30:6e:4c:cb:96 fxp0: [ITHREAD] pcib1: <ACPI Host-PCI bridge> on acpi0 pci32: <ACPI PCI bus> on pcib1 mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2100-0x21ff mem 0x90840000-0x90= 84ff2 mpt0: [ITHREAD] mpt0: MPI Version=3D1.2.12.0 mpt1: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem 0x90820000-0x90= 82ff2 mpt1: [ITHREAD] mpt1: MPI Version=3D1.2.12.0 bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x105> mem= 0x92 miibus1: <MII bus> on bge0 brgphy0: <BCM5701 10/100/1000baseTX PHY> PHY 1 on miibus1 brgphy0: =A010baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000= baseT-o bge0: Ethernet address: 00:30:6e:4c:ca:15 bge0: [ITHREAD] pcib2: <ACPI Host-PCI bridge> on acpi0 pci64: <ACPI PCI bus> on pcib2 pcib3: <ACPI Host-PCI bridge> on acpi0 pci96: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 1.0 on pci96 pci97: <ACPI PCI bus> on pcib4 ciss0: <HP Smart Array 6400> port 0x6000-0x60ff mem 0xb0080000-0xb0081fff,0= xb007 ciss0: [ITHREAD] pcib5: <ACPI Host-PCI bridge> on acpi0 pci128: <ACPI PCI bus> on pcib5 pcib6: <ACPI Host-PCI bridge> on acpi0 pci192: <ACPI PCI bus> on pcib6 pcib7: <ACPI Host-PCI bridge> on acpi0 pci224: <ACPI PCI bus> on pcib7 uart0: <16550 or compatible> mem 0xf4051000-0xf405100f irq 82 at device 1.0= on 4 uart0: [FILTER] puc0: <HP Diva Serial [GSP] Multiport UART - Everest SP2> mem 0xf4050000-0x= f4054 puc0: [FILTER] uart1: <Non-standard ns8250 class UART with FIFOs> on puc0 uart1: [FILTER] vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xf0000000-0xf3fff= fff,4 uart2: <16550 or compatible> iomem 0xff5e0000-0xff5e0007 irq 34 on acpi0 uart2: [FILTER] uart2: console (9600,n,8,1) uart3: <16550 or compatible> iomem 0xff5e2000-0xff5e2007 irq 35 on acpi0 uart3: [FILTER] uart3: debug port (9600,n,8,1) Timecounters tick every 1.000 msec Waiting 5 seconds for SCSI devices to settle md0: Preloaded image </boot/mfsroot> 8388608 bytes at 0xe000000004c6b670 acd0: DVDROM <DV-28E-B/2.2B> at ata2-master PIO4 init died (signal 0, exit 1) panic: Going nowhere without my init! cpuid =3D 1 KDB: enter: panic [thread pid 1 tid 100001 ] Stopped at =A0 =A0 =A0kdb_enter+0x81: [F1] =A0 =A0nop.f 0x0 db> bt Tracing pid 1 tid 100001 td 0xe000000010641b00 kdb_enter(0xe0000000049e6110, 0xe000000004536d20, 0x793, 0xa00000005df13398= ) at kdb_enter+0x81 panic(0xe0000000049e2da0, 0x0, 0x1, 0xc000000000000205, 0x20000000004cc8f8)= at p anic+0x2e0 exit1(0xe000000010641b00, 0x100) at exit1+0x120 sys_exit(0xe000000010641b00, 0xa00000005df134e8, 0xe0000000049889b0, 0x48e,= 0x0) at sys_exit+0x30 syscall(0xa00000005df13400, 0xe000000010641b00, 0xe00000001063ba70, 0xe0000= 00004 af52c8, 0x1, 0xa00000005df134e8, 0xe000000004984390, 0x8) at syscall+0x450 epc_syscall_return() at epc_syscall_return db>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?b5ef8d5c0906120848v48870590t1e25487729f6d4c6>