Date: Tue, 26 Jan 1999 21:08:36 -0600 From: "Erik Moe" <ehm@concentric.net> To: <questions@FreeBSD.ORG> Subject: 3.0-RELEASE install problems Message-ID: <002c01be49a2$5e936480$2f5b5b8f@nomad.gte.com>
next in thread | raw e-mail | index | archive | help
I'm getting the following error trying to do a CDROM install of 3.0-RELEASE on an HP Vectra 486/33u with an Adaptec 1740, SCSI Disk and SCSI CDROM: No CDROM devices found! Please check that your system's configuration is correct and that the CDROM drive is of a supported type. For more information, consult the hardware guide in the Doc menu. However, the CDROM appears to be detected at boot: avail memory = 4853760 (4740K bytes) eisa0: <HWPff09 (System Board)> Probing for devices on the EISA bus ahb0: <Adaptec 174x SCSI host adapter> at 0x1c00-0x1cff irq 11 on eisa0 slot 1 ahb0: AHA1740 Single Ended SCSI Adapter, FW Rev. E , ID=7, 64 ECBs Probing for devices on the ISA bus: video#0: WARNING: video mode switching is not fully supported on this adapter sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA color <4 virtual consoles, flags=0x0> ed0 at 0x300-0x30f irq 5 maddr 0xcc000 msize 8192 on isa ed0: address 02:60:8c:da:9a:f6, type 3c503 (16 bit) sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A lpt0 at 0x378-0x37f irq 7 on isa lpt0: Interrupt-driven port lp0: TCP/IP capable interface fdc0 at 0x3f0-03f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in aha0: not found at 0x134 npx0 on motherboard npx0: INT 16 interface Waiting 15 seconds for SCSI devices to settle ahb0: SCSI Bus Reset Delivered da0 at ahb0 bus 0 target 0 lun 0 da0: <HP D1699-60001 5732> Fixed Direct Access SCSI2 device da0: Tagged Queueing Enabled da0: 406MB (832527 512 byte sectors: 64H 32S/T 406C) cd0 at ahb0 bus 0 target 1 lun 0 cd0: <TOSHIBA CD-ROM XM-3301TA 0272> Removable CD-ROM SCSI2 device cd0: cd present [1075534577 x 1415061573 byte records] changing root device to fd0c rootfs is 1440 Kbyte compiled in MFS /stand/sysinstall running as init on vty0 I tried to use the "fixit" floppy to gain further insight, but I have been unsuccessful in getting sysinstall to load the "fixit" floppy. This same system works fine with 2.2.8-RELEASE. Any suggestions or comments would be welcome. Please be sure to "cc" my email address since I don't subscribe to freebsd-questions. Erik Moe ehm@concentric.net To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?002c01be49a2$5e936480$2f5b5b8f>