Date: Fri, 21 May 1999 05:36:30 -0400 From: Tom Embt <tom@embt.com> To: freebsd-hardware@freebsd.org Cc: "Donald J . Maddox" <dmaddox@conterra.com> Subject: Re: How to get AWE64 ISA PnP working? Message-ID: <3.0.3.32.19990521053630.00b5402c@mail.embt.com> In-Reply-To: <19990520193042.A1385@dmaddox.conterra.com> References: <Pine.BSF.4.05.9905201312350.4316-100000@bumlan.campus.luth.se> <3.0.3.32.19990520054937.00a98514@mail.embt.com> <Pine.BSF.4.05.9905201312350.4316-100000@bumlan.campus.luth.se>
next in thread | previous in thread | raw e-mail | index | archive | help
>> controller pnp0
>> device pcm0 at isa? port ? tty irq 10 drq 1 flags 0x0
>
>This is bad advice, as the feature that makes an AWE an AWE (wavetable
>synthesis) is not supported by the pcm device at all.
>
Thought so, it mentioned something like that on the AWEPnP webpage...
>To the original poster:
>
>I have an AWE64GOLD that works perfectly, in a configuration similar to
>yours. You may have another device that conflicts with the AWE, or the
>IRQ/DMA setup you specified in your kernel.conf may not match what your
>PnP BIOS is actually assigning your card. You need to post _complete_,
>unabridged dmesg output, and preferably, also the output from the
>'pnpinfo' command, if you want us to be able to puzzle out the source
>of your problems...
>
I'd be more than happy to - here goes:
-------
|dmesg|
-------
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.2-STABLE #0: Fri May 21 04:57:40 EDT 1999
root@paranor.embt.net:/usr/src/sys/compile/PARANOR-052199a
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 167046000 Hz
CPU: Pentium/P55C (167.05-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping=3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 100663296 (98304K bytes)
config> pnp 1 0 os enable irq0 5 drq0 1 drq1 5 port0 0x220 port1 0x330
port2 0x388
config> pnp 1 1 os disable
config> pnp 1 2 os port0 0x620 port1 0xa20 port2 0xe20
config> pnp 1 3 os disable
config> quit
avail memory = 94973952 (92748K bytes)
Preloaded elf kernel "kernel" at 0xc02b6000.
Preloaded userconfig_script "/kernel.config" at 0xc02b609c.
Probing for devices on PCI bus 0:
chip0: <Intel 82439TX System Controller (MTXC)> rev 0x01 on pci0.0.0
chip1: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip2: <Intel 82371AB Power management controller> rev 0x01 on pci0.7.3
vga0: <S3 ViRGE graphics accelerator> rev 0x05 int a irq 9 on pci0.9.0
pn0: <82c169 PNIC 10/100BaseTX> rev 0x20 int a irq 10 on pci0.11.0
pn0: Ethernet address: 00:c0:f0:2d:ec:69
pn0: autoneg complete, link status good (half-duplex, 10Mbps)
Probing for PnP devices:
CSN 1 Vendor ID: CTL00c5 [0xc5008c0e] Serial 0x157aac6a Comp ID: PNPb02f
[0x2fb0d041]
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 not found
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
ppc0 at 0x378 irq 7 on isa
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <IBM-DTTA-351010>
wd0: 9671MB (19807200 sectors), 19650 cyls, 16 heads, 63 S/T, 512 B/S
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (atapi): <CD-ROM CDU55E/1.0u>, removable, accel, dma, iordy
acd0: drive speed 344KB/sec, 256KB cache
acd0: supported read types: CD-DA
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM unknown medium, unlocked
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
sb0 at 0x220 irq 5 drq 1 on isa
snd0: <SoundBlaster 16 4.16>
sbxvi0 at drq 5 on isa
snd0: <SoundBlaster 16 4.16>
sbmidi0 at 0x330 on isa
snd0: <SoundBlaster MPU-401>
opl0 at 0x388 on isa
snd0: <Yamaha OPL3 FM>
awe0 at 0x620 on isa
AWE32: not detected
Intel Pentium detected, installing workaround for F00F bug
changing root device to wd0s1a
cd9660: Joliet Extension
---------
|pnpinfo|
---------
Checking for Plug-n-Play devices...
Card assigned CSN #1
Vendor ID CTL00c5 (0xc5008c0e), Serial Number 0x157aac6a
PnP Version 1.0, Vendor Version 16
Device Description: Creative SB AWE64 PnP
*** Small Vendor Tag Detected
Logical Device ID: CTL0045 0x45008c0e #0
Device Description: Audio
TAG Start DF
Good Configuration
IRQ: 5 - only one type (true/edge)
DMA: channel(s) 1
8-bit, not a bus master, count by byte, , Compatibility mode
DMA: channel(s) 5
16-bit, not a bus master, , count by word, Compatibility mode
I/O Range 0x220 .. 0x220, alignment 0x1, len 0x10
[16-bit addr]
I/O Range 0x330 .. 0x330, alignment 0x1, len 0x2
[16-bit addr]
I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
DMA: channel(s) 5 6 7
16-bit, not a bus master, , count by word, Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2
[16-bit addr]
I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
DMA: channel(s) 5 6 7
16-bit, not a bus master, , count by word, Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
DMA: channel(s) 5 6 7
16-bit, not a bus master, , count by word, Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2
[16-bit addr]
I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2
[16-bit addr]
TAG Start DF
Acceptable Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
TAG Start DF
Sub-optimal Configuration
IRQ: 5 7 9 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, count by byte, , Compatibility mode
DMA: channel(s) 5 6 7
16-bit, not a bus master, , count by word, Compatibility mode
I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10
[16-bit addr]
I/O Range 0x300 .. 0x330, alignment 0x10, len 0x2
[16-bit addr]
I/O Range 0x388 .. 0x394, alignment 0x4, len 0x4
[16-bit addr]
TAG End DF
Logical Device ID: CTL7002 0x02708c0e #1
Compatible Device ID: PNPb02f (2fb0d041)
Device Description: Game
TAG Start DF
Good Configuration
I/O Range 0x200 .. 0x200, alignment 0x1, len 0x8
[16-bit addr]
TAG Start DF
Acceptable Configuration
I/O Range 0x200 .. 0x208, alignment 0x8, len 0x8
[16-bit addr]
TAG End DF
Logical Device ID: CTL0022 0x22008c0e #2
Device Description: WaveTable
TAG Start DF
Good Configuration
I/O Range 0x620 .. 0x620, alignment 0x1, len 0x4
[16-bit addr]
TAG Start DF
Acceptable Configuration
I/O Range 0x620 .. 0x680, alignment 0x20, len 0x4
[16-bit addr]
TAG End DF
*** Small Vendor Tag Detected
End Tag
Successfully got 69 resources, 3 logical fdevs
-- card select # 0x0001
CSN CTL00c5 (0xc5008c0e), Serial Number 0x157aac6a
Logical device #0
IO: 0x0220 0x0330 0x0388 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 5 0
DMA 1 5
IO range check 0x00 activate 0x01
Logical device #1
IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 0 0
DMA 4 4
IO range check 0x00 activate 0x00
Logical device #2
IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 0 0
DMA 4 4
IO range check 0x00 activate 0x00
-----------------
|/boot/loader.rc|
-----------------
load kernel
load -t userconfig_script /kernel.config
boot
----------------
|/kernel.config|
----------------
pnp 1 0 os enable irq0 5 drq0 1 drq1 5 port0 0x220 port1 0x330 port2 0x388
pnp 1 1 os disable
pnp 1 2 os port0 0x620 port1 0xa20 port2 0xe20
pnp 1 3 os disable
quit
----------------------------------------
|excerpt from kernel configuration file|
| (the whole thing is pretty long) |
----------------------------------------
controller pnp0
controller snd0
device sb0 at isa? port 0x220 irq 5 drq 1
device sbxvi0 at isa? drq 5
device sbmidi0 at isa? port 0x330
device opl0 at isa? port 0x388
device awe0 at isa? port 0x620
----------
|uname -v|
----------
FreeBSD 3.2-STABLE #0: Fri May 21 04:57:40 EDT 1999
root@paranor.embt.net:/usr/src/sys/compile/PARANOR-052199a
------------------------------------------
Was I incorrect in putting the 'load -t userconfig_script /kernel.config'
line in /boot/loader.rc? That is about the only thing that I didn't follow
the instructions exactly on. Also, FWIW, this machine is a dual-boot and
in Win95 the AWE card uses all the standard addresses (IRQ 5 ; DMA 1,5 ;
ports 0x220 0x330 0x388 0x620). The only other cards in the machine are a
PCI S3-ViRGE video, PCI Voodoo 2, and a PCI Kinston PNIC network card
(pn0). IIRC, BIOS is giving IRQ 5 to "ISA/PCI PnP" or something like that,
and I think "PNP OS" is enabled 'cause of Windoze. I'd have to reboot to
be sure.
Tom Embt
tom@embt.com
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3.0.3.32.19990521053630.00b5402c>