Date: Sun, 29 Apr 2001 19:40:31 +0200 (CEST) From: Torbjorn Kristoffersen <sgt@netcom.no> To: FreeBSD-Hackers <hackers@FreeBSD.org> Subject: Trouble with HPT366 Message-ID: <Pine.BSF.4.30.0104291923200.1667-100000@hal.netforce.no>
next in thread | raw e-mail | index | archive | help
I'm having trouble with my HighPoint 366 controller. Both the chip and
cable works fine in Linux or Windows, but I get an error message from
FreeBSD 4.3-RC2 that says "DMA limited to UDMA33, Non-ATA66 compliant
cable."
Here is my dmesg output with a kernel verbosely booted. I have carefully
erased a few unimportant lines, to make it shorter and more readable.
I'd appreciate help/advice on this. I've been reading a bit through
/sys/dev/ata/* and what causes the error _message_ is that
"ATA_PARAM(scp, device)->cblid" returns zero (ata-dma.c:105). cblid lies
in struct ata_params. But I'm not sure what to do with this.
Torbjorn Kristoffersen
sgt@netcom.no
PS: I've had this problem with the predecessors of FreeBSD as well.
====== Start of dmesg output ======
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-RC2 #2: Tue Apr 10 00:32:38 CEST 2001
sgt@hal.netforce.no:/usr/src/sys/compile/HAL
Calibrating clock(s) ... TSC clock: 701682801 Hz, i8254 clock: 1193338 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 701593899 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (701.59-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268435456 (262144K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00382000 - 0x0fff7fff, 264724480 bytes (64630 pages)
avail memory = 257200128 (251172K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00faf90
bios32: Entry = 0xfb410 (c00fb410) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb440
pnpbios: Found PnP BIOS data at 0xc00fc010
pnpbios: Entry = f0000:c038 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc035c000.
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e4000000, size 25
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f000, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=255
map[20]: type 1, range 32, base 0000d000, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00005000, size 4
found-> vendor=0x10ec, dev=0x8029, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000d400, size 5
found-> vendor=0x1103, dev=0x0004, revid=0x01
class=01-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000d800, size 3
map[14]: type 1, range 32, base 0000dc00, size 2
map[20]: type 1, range 32, base 0000e000, size 8
found-> vendor=0x1103, dev=0x0004, revid=0x01
class=01-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=11
map[10]: type 1, range 32, base 0000e400, size 3
map[14]: type 1, range 32, base 0000e800, size 2
map[20]: type 1, range 32, base 0000ec00, size 8
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x102b, dev=0x0525, revid=0x04
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base e6000000, size 25
map[14]: type 1, range 32, base e0000000, size 14
map[18]: type 1, range 32, base e1000000, size 23
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) at 0.0 irq 9
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 status0=50 status1=50
ata0: mask=03 ostat0=50 ostat2=50
ata0-master: ATAPI probe a=00 b=00
ata0-slave: ATAPI probe a=00 b=00
ata0: mask=03 status0=50 status1=50
ata0-master: ATA probe a=01 b=a5
ata0-slave: ATA probe a=01 b=a5
ata0: devices=03
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=02 status0=ff status1=50
ata1: mask=02 ostat0=ff ostat2=50
ata1-slave: ATAPI probe a=14 b=eb
ata1: mask=02 status0=ff status1=00
ata1: devices=08
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 7.2
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at device 7.3 on pci0
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xd400-0xd41f irq 10 at device 13.0 on pci0
bpf: ed0 attached
ed0: address 00:50:bf:03:ad:a2, type NE2000 (16 bit)
atapci1: <HighPoint HPT366 ATA66 controller> port 0xe000-0xe0ff,0xdc00-0xdc03,0xd800-0xd807 irq 11 at device 19.0 on pci0
ata2: iobase=0xd800 altiobase=0xdc02 bmaddr=0xe000
ata2: mask=03 status0=50 status1=30
ata2: mask=03 ostat0=50 ostat2=30
ata2-master: ATAPI probe a=00 b=00
ata2-slave: ATAPI probe a=30 b=30
ata2: mask=03 status0=50 status1=30
ata2-master: ATA probe a=01 b=a5
ata2-slave: ATA probe a=a5 b=25
ata2: devices=01
ata2: at 0xd800 on atapci1
atapci2: <HighPoint HPT366 ATA66 controller> port 0xec00-0xecff,0xe800-0xe803,0xe400-0xe407 irq 11 at device 19.1 on pci0
ata-: ata2 exists, using next available unit number
ata3: iobase=0xe400 altiobase=0xe802 bmaddr=0xec00
ata3: mask=03 status0=20 status1=30
ata3: mask=03 ostat0=20 ostat2=30
ata3-master: ATAPI probe a=20 b=20
ata3-slave: ATAPI probe a=30 b=30
ata3: mask=03 status0=20 status1=30
ata3-master: ATA probe a=25 b=25
ata3-slave: ATA probe a=25 b=25
ata3: devices=00
ata3: at 0xe400 on atapci2
using shared irq11.
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
CTL0045: start dependant
CTL0045: adding irq mask 0x20
CTL0045: adding dma mask 0x2
CTL0045: adding dma mask 0x20
CTL0045: adding io range 0x220-0x22f, size=0x10, align=0x1
CTL0045: adding io range 0x330-0x331, size=0x2, align=0x1
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependant
isa0: too many dependant configs (8)
CTL7002: start dependant
CTL7002: adding io range 0x200-0x207, size=0x8, align=0x1
CTL7002: start dependant
CTL7002: adding io range 0x200-0x20f, size=0x8, align=0x8
CTL7002: end dependant
CTL0022: start dependant
CTL0022: adding io range 0x620-0x623, size=0x4, align=0x1
CTL0022: start dependant
CTL0022: adding io range 0x620-0x683, size=0x4, align=0x20
CTL0022: end dependant
isa0: unexpected small tag 14
ex_isa_identify()
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata4 failed to probe at port 0x1f0 irq 14 flags 0xb0ffb0ff on isa0
ata5 failed to probe at port 0x170 irq 15 flags 0xb0ffb0ff on isa0
sbc0 failed to probe at port 0x220-0x22f irq 5 drq 1 flags 0x15 on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:030ffe3f 0..783=784 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fe3f3f 0..1022=1023 cylinders, 0..63=64 heads, 1..63=63 sectors
2:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c840, tty 6310ba, net 6714ba
ata0-master: success setting UDMA2 on PIIX4 chip
Creating DISK ad0
Creating DISK wd0
ad0: <WDC AC36400L/09.09M08> ATA-4 disk at ata0-master
ad0: 6149MB (12594960 sectors), 13328 cyls, 15 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
ad0: 6149MB <WDC AC36400L> [13328/15/63] at ata0-master UDMA33
ata0-slave: success setting UDMA2 on PIIX4 chip
Creating DISK ad1
Creating DISK wd1
ad1: <ST32122A/0.42> ATA-2 disk at ata0-slave
ad1: 2014MB (4124736 sectors), 4092 cyls, 16 heads, 63 S/T, 512 B/S
ad1: 16 secs/int, 1 depth queue, UDMA33
ad1: piomode=4 dmamode=2 udmamode=2 cblid=0
ad1: 2014MB <ST32122A> [4092/16/63] at ata0-slave UDMA33
ata2-master: DMA limited to UDMA33, non-ATA66 compliant cable
ata2-master: success setting UDMA2 on HighPoint chip
Creating DISK ad4
Creating DISK wd4
ad4: <WDC WD205BA/16.13M16> ATA-4 disk at ata2-master
ad4: 19574MB (40088160 sectors), 39770 cyls, 16 heads, 63 S/T, 512 B/S
ad4: 16 secs/int, 1 depth queue, UDMA33
ad4: piomode=4 dmamode=2 udmamode=4 cblid=0
HighPoint check1 failed
ad4: 19574MB <WDC WD205BA> [39770/16/63] at ata2-master UDMA33
ata1-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-slave: success setting PIO4 on generic chip
acd0: <FX320S/q01> CDROM drive at ata1 as slave
acd0: read 5512KB/s (5512KB/s), 256KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM 120mm photo disc loaded, unlocked
Mounting root from ufs:/dev/ad4s1a
ad4s1: type 0xa5, start 63, end = 40082174, size 40082112 : OK
start_init: trying /sbin/init
ad0s1: type 0x6, start 63, end = 4192964, size 4192902 : OK
ad0s2: type 0x5, start 4192965, end = 12594959, size 8401995 : OK
ad0s5: type 0xb, start 4193028, end = 12594959, size 8401932 : OK
====== End of dmesg output ======
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.30.0104291923200.1667-100000>