Date: Wed, 05 Feb 2014 21:42:57 +0100 From: kaczorem <kaczorem@iem.pw.edu.pl> To: freebsd-virtualization@freebsd.org Subject: Disks are not shown on Adaptec 5805 (added via passthrough to the VM) Message-ID: <76a98a271ebb61b01a1f2bcc6c4da479@iem.pw.edu.pl>
next in thread | raw e-mail | index | archive | help
Hello, I created a virtual machine with installed FreeBSD on ESXi 5.5. I added controller Adaptec 5805 to the VM via passthrough. FreeBSD detects aac controller but does not show disks. (it does not matter whether JBODs or logical volumes are configured on Adaptec) I did some tests and ex. it works well on Ubuntu - I can use all disks on controller which was added via passhrough to the virtual machine with Ubuntu. Everything works well under "physical" FreeBSD. logs: aac0: <Adaptec RAID 5805> mem 0xfd200000-0xfd3fffff irq 18 at device 0.0 on pci3 aac0: Enabling 64-bit address support aac0: Enable Raw I/O aac0: Enable 64-bit array aac0: New comm. interface enabled aac0: Adaptec 5805, aac driver 2.1.9-1 aacp0 on aac0 aacp1 on aac0 aacp2 on aac0 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Retrying command (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Retrying command (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Retrying command (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Retrying command (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Retrying command (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error (probe2:aacp2:0:0:0): Error 5, Retries exhausted ses0 at aacp2 bus 0 scbus4 target 0 lun 0 ses0: <AIC SES_BP-4D-1F 130a> Fixed Enclosure Services SCSI-5 device ses0: 3.300MB/s transfers (8bit) ses0: SCSI-3 ENC Device regards,
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?76a98a271ebb61b01a1f2bcc6c4da479>