Date: Fri, 6 Feb 2009 14:42:26 -0500 From: L Campbell <llc2w@virginia.edu> To: freebsd-current@freebsd.org Subject: iwi broken? reproducible crash :( Message-ID: <792298050902061142k33f35be7sb19d566835e796ad@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
I recently updated to CURRENT from RELENG_7 (from sources pulled on
Feb. 6th), and since then haven't been able to get my Inspiron 6000's
Intel PRO 2200/BG working again (it worked mostly fine on RELENG_7).
The machine is running an i386 non-GENERIC kernel (I can post the
configuration if it's relevant).
The settings on the device (set from rc.conf) configured for my home
network (which experiences the same problem) look like this --
$ ifconfig iwi0
iwi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 00:16:6f:63:a6:dc
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
status: associated
$ ifconfig wlan0
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:16:6f:63:a6:dc
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
ssid home_ssid channel 5 (2432 Mhz 11g)
country US authmode OPEN privacy OFF txpower 0 bmiss 24 scanvalid 60
protmode CTS wme bintval 0
When attempting to associate with an access point (without any
encryption or additional complications), the console gets flooded with
a barrage of messages --
$ ifconfig wlan0 down ssid wahoo bssid - channel 11 up
iwi0: need multicast update callback
iwi0: iwi_cmd: cmd 84 not sent, busy
iwi0: iwi_cmd: cmd 42 not sent, busy
iwi0: firmware error
Enabling debug via `$ sysctl debug.iwi=1` reproducibly causes the
kernel to crash:
Unread portion of the kernel message buffer:
exit SCANNING state
iwi_ops: SET_WME arg 0
iwi_newstate: SCAN -> AUTH flags 0x1
iwi_ops: AUTH arg 192
enter ASSOCIATING state
Configuring adapter
Setting ESSID to "wahoo"
Setting power mode to 0
Setting RTS threshold to 2346
Setting fragmentation threshold to 2346
Setting negotiated rates (12)
Setting WME parameters
Setting WME IE (len=7)
Setting sensitivity to 69
Join bssid 00:19:07:05:99:c3 dst 00:19:07:05:99:c3 channel 11 policy
0x1 auth 0 capinfo 0x21 lintval 100 bintval 100
iwi_newstate: AUTH -> ASSOC flags 0x1
exit ASSOCIATING state
iwi_newstate: ASSOC -> SCAN flags 0x1
iwi_ops: SET_WME arg 0
iwi_newstate: SCAN -> AUTH flags 0x1
iwi_ops: AUTH arg 192
enter ASSOCIATING state
Configuring adapter
exit ASSOCIATING state
Setting ESSID to "wahoo"
iwi_newSetting power mode to 0
state: AUTSetting RTS threshold to 2346
H -> SCAN Setting fragmentation threshold to 2346
flags 0x9Setting negotiated rates (12)
Setting WME parameters
iwi_newSetting WME IE (len=7)
state: SCA
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0xc40ee184
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc06bea06
stack pointer = 0x28:0xc3a05b64
frame pointer = 0x28:0xc3a05b64
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 0 (iwi0 taskq)
kgdb> bt
#12 0xc06bea06 in node_getrssi (ni=0xc40ee000)
at /usr/src/sys/net80211/ieee80211_node.c:1005
#13 0xc051286c in iwi_ops (arg0=0xc3d4ec00, npending=1)
at /usr/src/sys/dev/iwi/if_iwi.c:2926
#14 0xc062d042 in taskqueue_run (queue=0xc3d73180)
at /usr/src/sys/kern/subr_taskqueue.c:282
#15 0xc062d3db in taskqueue_thread_loop (arg=0xc3d4ec4c)
at /usr/src/sys/kern/subr_taskqueue.c:403
#16 0xc05d6e80 in fork_exit (callout=0xc062d360 <taskqueue_thread_loop>,
arg=0xc3d4ec4c, frame=0xc3a05d38) at /usr/src/sys/kern/kern_fork.c:821
#17 0xc07daf70 in fork_trampoline () at /usr/src/sys/i386/i386/exception.s:270
kgdb> f 12
kgdb> list
0xc06bea06 is in node_getrssi (/usr/src/sys/net80211/ieee80211_node.c:1005).
1000 }
1001
1002 static int8_t
1003 node_getrssi(const struct ieee80211_node *ni)
1004 {
1005 uint32_t avgrssi = ni->ni_avgrssi;
1006 int32_t rssi;
1007
1008 if (avgrssi == IEEE80211_RSSI_DUMMY_MARKER)
1009 return 0;
kgdb> p ni
$1 = (const struct ieee80211_node *) 0xc40ee000
I dunno if this is the right channel to post the information (or even
if I'm posting anything useful). Let me know if you need more
information or have any ideas/suggestions/patches to test. Thanks a
bunch :3
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?792298050902061142k33f35be7sb19d566835e796ad>